Showing results: 286 - 300 of 2372 items found.
-
RY2-1 -
Shanghai Jiuzhi Electric Co., Ltd.
This temperature control unit is used to regulate the desired temperature of the solid insulants test cell RY2The temperature range can be set up to 300°C
-
Shanghai Himalayal Co.
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
ST5C Colibri -
Advance Devices Corp.
*Built-in direct LCR probe*Convenient one-hand operation*Ideal for Surface Mount Devices*Automated component identification*Automated test range selection*Manual C, R, L and ESR modes*Manual test frequency overrides*Test signal level 0.5 Vrms*Portable and ergonomic design*OLED Display*Built-in Li-Ion battery
-
129610A -
Ametek Scientific Instruments
Liquid nitrogen (LN2) or liquid helium (LHe) can be used as the cryogen depending on the required operating temperature range. This allows standard tests to be performed using relatively low cost LN2 as the cryogen. Higher cost LHe can be substituted for the duration of tests where very low temperature is required, providing an economical solution to your test requirements.
-
PITC -
Bemco Inc.
The PITC, with a temperature range of -70 C to +177 C, was first introduced in the late 1950s by Bemcos Conrad/Missimer Division. Today, the modernized version of this system is the ideal solution where short run or infrequent tests are required, test specimens are unusual in size or shape, initial capital costs must be held low, or test needs are frequently changed.
-
Optomistic Products
Optomistic Products’ unique Two-Part Solution fulfills almost every LED test requirement you may have.First, determine your test requirements. For example: LED color and intensity test with an analog output, or, LED ON/OFF status with a digital output, etc. Then, choose from the range of Sensors listed below to address those requirements.
-
93-022-226 -
Pickering Interfaces Ltd.
The 93-002-226 104-pin to 96-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
93-022-245 -
Pickering Interfaces Ltd.
The 93-002-245 104-pin to 100-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Desco Industries, Inc.
Analog Compliance Verification Surface Resistance CheckerUse to test worksurfaces, shelving, carts, garments, chairs to ANSI/ESD S20.20 per ESD TR53Automatic Test Range Voltage Selection Per Compliance Verification ESD TR53Starts tests at 10 volts and automatically switches to 100 volts if the measurement is over 105 ohmsPortable Operation with 9 Volt Battery
-
40-682A-002 -
Pickering Interfaces Ltd.
The 40-682A-002 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 250mA current and 40V voltage handling. The 40-682A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
40-681A-001 -
Pickering Interfaces Ltd.
The 40-681A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 350mA current and 60V voltage handling. The 40-681A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
40-683A-001 -
Pickering Interfaces Ltd.
The 40-683A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 125mA current and 100V voltage handling. The 40-683A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Seaward Group USA
The range of resistance decade boxes includes 5, 6 and 8 decade boxes which are designed to provide highly accurate and variable standard values of resistance and current for calibration, comparison and test applications in electrical and electronic workshops, test laboratories and educational environments
-
HH2109 -
Colluck Company Limited
High Accuracy (Basic Accuracy 0.7%). LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A
-
CAL-AV Labs, Inc.
he CAL-AV Research & Electronic Test Product line includes Explosive Test Site Range Instrumentation, Illuminated Laser Warning Signs and Special Projects.. Firesets, CDU’s EDU’s, Delay generators, firing panels, and custom instruments. Fiber-optic and computer-control options.