Proximity Sensors
Non-contact detection of an object within a specified range.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
product
Solar Radiation Sensors & Transmitters
A70 Series
The Comptus A70 Series solar radiation sensors with transmitters are available in two models. The A70-A PAR Sensor measures photosynthetically active radiation (PAR) in the 400 to 700 nm range. The A70-I Insolation Sensor measures solar radiation in the 280 to 2800 nm range. The signals from the sensors are scaled by the signal conditioner to provide the desired output.
-
-
product
Digital Magnetic Speed Sensors
DIGISPEC
SPECTEC Innovative Sensor Solutions
SPECTEC'S digital magnetic sensor, or active Variable Reluctance (VR) sensor, is a magnetic speed sensor coupled with an analog to digital signal conditioner in one compact unit. The digital magnetic sensor's solid state internal analog to digital converter creates a digital output signal from the magnetic pickup's analog signal created by the excitation due to a passing target. The digital output from sensing a vehicle's rotating gear or a cotter key slot can be read by counters, meters or governing instrumentation.
-
product
SparkFun Soil Moisture Sensor
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be and will result in a lower resistance, and a higher SIG out.
-
product
Single Axis AC Magnetic Field Sensor
MGC-1
Macintyre Electronic Design Associa
The MGC-1 is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1 amplitude response is insensitive to the frequency of the field over its 5 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-22
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for leakage current measurements*Ultra compact size*AC 1mA～100A
-
product
Safety Relay Modules & Sensors
Using safety relay modules, you can reliably implement safety functions in machines and systems. They monitor signals from emergency stop buttons, light grids, and safety door switches, and initiate a safe state where necessary.
-
product
Strain Sensors
Columbia Research Laboratories
Columbia's foil strain sensors monitor the fatigue loading experienced by tactical aircraft under various conditions of speed, weight and missions configuration. Critical undercarriage structures and control surfaces may be monitored for fatigue damage induced by high-G maneuvers and high stress landings. These sensors are self-temperatures compensating, environmental resistant, have a high output, two active arms and are easily installed. Developed for the demanding requirements associated with tactical military aircraft, they are equally useful performing many of the more common strain measurements encountered in the material testing laboratory. Columbia's foil strain sensors are considered the standard for the industry.
-
product
Lambda Oxygen Sensor
KS60002
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
SparkFun Gas Sensor Breakout
This is a simple breakout board for the MQ - 3, MQ - 4, MQ - 6, MQ - 7, and MQ - 8 gas sensors. With the Gas Sensor Breakout you will be able to utilize each oversized, oddly spaced pins featured on every MQ gas sensor product. This is an extremely handy and economical board to have around when detecting multiple types of gases.
-
product
Temperature Sensors
Robust temperature transducerWith integrated Pt1000 sensorOutput signal 0-10VTemperature range -30 to 80 CPower supply 15-30Vdc / 24VacSupplied with calibration certificate
-
product
BME680 Environmental Sensor
28061
Raise your project’s environmental awareness with the BME680. The Bosch Sensortec BME680 Integrated Environmental Unit combines a gas sensor with air pressure, humidity, and ambient air temperature sensing functions within a single package for high performance air quality measurement. Parallax Inc. places the BME680 on a compact PCB with a 6-pin male header. This capable sensor does not have to be difficult to use. The BME680 is supported by BlocklyProp visual programming as well as C libraries for the Propeller multicore microcontroller. Code for other controllers is available from the Bosch Github repository.
-
product
CMOS Type Micro Laser Distance Sensor
HG-C1000L
Panasonic Industrial Devices Sales Company of America
The IO-Link technology makes it possible to continuously collect and process data and to control the HG-C1000L. This allows users to implement predictive maintenance and to monitor the operation in machines and assembly lines. Processing the multitude of data requires users to invest know-how and time. To reduce the workload for the customers, Panasonic has developed a self-diagnosis function specifically for this sensor. This function sends sensor data via IO-Link to a higher-level fieldbus, thus informing about the state of the sensor directly. This way, the amount of production data and the work needed to analyze the data is reduced.
-
product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745690-T002
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
product
Dual Sensor Enhanced Vision Systems
EVS
Enhance your safety and situational awareness while flying with Max-Viz dual sensor enhanced vision systems (EVS) from Astronics. These multi-spectral imagers include a long wave infrared sensor, a visible light + near infrared sensor, and patented blending and dynamic range management image processing to enable pilots to see clearly during day and night.
-
product
Sensor Bodies
The armature - assembled sensor body - is the central component of an inline photometer. We have already designed more than 1000 different sensor bodies and more than 50 types are always on stock. All optek inline sensor bodies are made from high quality materials and are machined with extreme precision. The quality-tested manufacturing tolerances allow optical path lengths of up to 1000 mm, for which the accuracy of the incoming and outgoing light beam is ensured by testing a laser-based coaxiality tolerance test to the reference axis. To cover a wide spectrum of different process conditions, optek sensor bodies can be manufactured from various materials (also for aggressive chemicals or with NACE MR 0175) and adapted with regards to:
-
product
Magnetic Field Sensor
Vernier Software & Technology, LLC
The Magnetic Field Sensor can be used to study the field around permanent magnets, coils, and electrical devices. It features a rotating sensor tip to measure both transverse and longitudinal magnetic fields.
-
product
SparkFun RGB And Gesture Sensor
APDS-9960
This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand! This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price.
-
-
product
Compact Flow Sensor Lapiflow (R)
FSM3
It is a flow sensor that can support 5 types of gas such as air, nitrogen, argon, carbon dioxide, mixed gas with one unit.
-
product
Multi-Mission EO/IR Surveillance Sensor
Star SAFIRE® III
With thousands of systems fielded, the Star SAFIRE III provides extremely reliable high performance. Along with superior image stabilization and long-range imaging, Star SAFIRE III features internal navigation for precise targeting, MWIR thermal imager, optional EO color and low-light cameras, and multiple laser payload options. The system is fully hardened for military fixed-wing and helicopter operations, and it operates continuously in all conditions – even while sitting on the tarmac with no airflow.
-
product
Suitable for Thermocouple Sensors Approved to ATEX and IECEx standards
TTC200X
Approved to ATEX and IECEx standards allowing for use in hazardous area applications.
-
product
Digital Meteorological Sensor
ZET 7023
The ZET 7023 weather sensor is a measuring unit with two in-built sensors one of which is responsible for measuring relative humidity and temperature, and the other one, for atmospheric pressure measuring.
-
product
Temperature Sensor
Precision temperature sensors from Stellar Technology are in demand worldwide for a variety of industrial test, measurement and process control applications.
-
product
Optical Sensors
Analog Devices optical sensors are optical sensing front ends that include integrated ultra-low noise amplification and high performance photodiodes. These solutions are used to achieve the highest performance for instrumentation, industrial, or clinical applications; or to optimize a solution to achieve the lowest power dissipation at a given performance level for battery powered and portable applications.
-
product
PSI5 Sensor Interface Card
SET-1640
PSI5 is an open standard based on existing sensor interfaces for peripheral airbag sensors and has already proven itself in millions of airbag systems.
-
product
Ultrasonic Sensors
Measure distance by using ultrasonic waves.The sensor head emits an ultrasonic wave and receives the wave reflected back from the target. Ultrasonic Sensors measure the distance to the target by measuring the time between the emission and reception.
-
product
Non Contact Temperature Sensors
Non Contact Type temperature measurement involves determining temperature of object surface without direct contact with the surface. Tempsens offers both single point and area inspection model devices which are infrared thermometers and infrared camera and industrial furnace monitoring camera.
