Tension
forces causing extension.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Gravity, Electrical, Magnetic, Tensiometers, Tensile, Extensometers
-
product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
product
Control Cables
TRIUMPH specializes in cable controls which are mechanical connections between controls and actuation systems used in a variety of applications. Our systems provide higher reliability, lighter weight, and greater control box selection. Current controls include wire rope, push-pull controls, sliding friction controls, ball-bearing controls and low-resistance and backlash mechanical control system cables. Wire Rope Controls: Wire Rope is used in applications where weight is critical, and the system operates in tension only. Assemblies are built to your required standards with unlimited configuration capabilities. Sliding Friction Controls: High load capacity in tension and compression. Flexible in any direction, wide temperature range and easy installation. No adjustment or lubrication needed during the life of the control. Ball Bearing Controls: Ball Bearing controls are a self-contained system that performs linear motion under tension or compression loads.Precise and accurate movement with high load capacity offering weight savings, low friction and high efficiency. Quick disconnect ends available.
-
product
Fryma Extension Tester
TF143
TESTEX Testing Equipment Systems Ltd.
Fryma Extension Tester, to simply and economically determine the stretch and recovery of textile fabrics, both knitted and woven. The apparatus consists of a loading frame with clamps and a screw tensioning device, two 3kg loading weights and sample cutting templates.
-
product
Computer Control Tensile Testing Machine
SG-L03B
These series of universal testing machine are used to test tension, compression, bend, shearing force, adhesion, peeling force, tear strength,...etc. of specimen, semi-product and finished product in the field of rubber, plastic, metal, nylon, fabric, paper, aviation, packing, architecture, petrochemistry, electric appliance, automobile,...etc. , which are the basic facilities for input quality contorl (I.Q.C), Quality Control (Q.C.), Physical Inspection, Mechanics Research and Material.
-
product
Tensile Test Chambers
Tensile strength tests are an integral part of material development. Materials that require this test include various metals, plastics, paper, fabrics, fibers, composites, and films for many industries. ESPEC tensile test chambers are designed to work with any tension apparatus and can be customized to meet unique application needs.
-
product
Dual Space Electro-hydraulic Servo Universal Testing Machine
WAW-E Series
Jinan Testing Equipment IE Corporation
WAW-E series computer control servo-hydraulic testing machine is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, the servo-hydraulic tester of dual space is capable of controlling the test procedures by the predetermined programs. The computer control servo-hydraulic testing machine can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The servo-hydraulictesting machine is easy to operate and is versatile in the applications of metallurgy industries such as steel mills & alloy, reinforced bar, aircraft manufacturer, research institutes, laboratories, calibration institutes etc.
-
product
Saddleback Monitor
SBM-1.0
The DLM Saddleback is a line tension monitor suited for more delicate cable, including telecommunication cables or large cable where a Running Line Monitor is unsuitable.
-
product
ACoustic QUantification of IncidenTs
ACQUIT
In regions with tensions, the cease fires agreed upon along a border line are usually fragile. The global community is often asked to send in observers trying to maintain the peace and to report on violations from both sides. There is a need for well described events in the formal reporting, when, where, what kind of weapon etc.
-
product
ES-Mini
On-site consultation, the ESMini enables the expert to quickly and easily assess the situation with regard to body tension and the decision on further measures / examinations. Because of its very simple handling, the ESMini is also suitable for regular testing by the person concerned.
-
product
Tension/ Compression Testing
Materials Evaluation and Engineering
Mechanical testing can provide vital information about fundamental material properties or act as a direct measurement of a component’s functional capabilities. Physical testing can ensure that products meet the specified requirements and can withstand the loads expected to be encountered during service.
-
product
High Temperature Un-Cooled Extensometers (700 C)
Model 7642
Jinan Testing Equipment IE Corporation
These extensometers use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7642 is ideal for testing composites, metals and high temperature polymers in tensile, compression or cyclic testing. All units can be displaced in both compression and tension. The extensometer is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the extensometer. This system provides a number of functional enhancements, including high speed digital output, built in calibration and tare functions, analog and digital filters, and more.
-
product
Polarization Controller and Scrambler - MATRIQ
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
product
Miniature S-Beam Load Cell
500 Series
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
product
Zipper Tester
TESTEX Testing Equipment Systems Ltd.
Zipper Tester, to determine the resistance to reciprocation of zipper (slide fastener), the test specimen is subjected to a specified number of cyclic operations whilst under lateral and longitudinal tension. Zipper Tester complies with BS 3084, CNS -1083, QB/T2171-1995, etc. Please contact us for more about information about pull test procedure.
-
product
Electromagnetic Resonance High Frequency Fatigue Testing Machine
PLG Series
Jinan Testing Equipment IE Corporation
The series of electromagnetic resonance fatigue testing machines are used for fatigue tests of metal materials and components under tension, compression or reversal loads. If relevant grips are provided, three-point bending test, four-point and circle test, gear wheat, bolt, connecting rod, roller chain, crackle expanding test can be available. The series of electromagnetic resonance fatigue testing machines feature an optimized design and a rational structure. The automatic controlled system adopts an advanced and wide-pulse-control system and a new-type of power amplifier to improve the reliability of the electric system. The electromagnetic resonance fatigue testing system is with high efficiency, easy and non-stop shake, low energy consuming, accurate control, and small fluctuation.
-
product
Force Gauge
Tension & compression capability .* 5000 g, wide capacity, highresolution, high accuracy, highrepeatability.* 3 kind display unit, g/oz/Newton.* Separate sensor.* Peak hold ( Max. load ) measurement.* Positive or reverse display direction.* Hand held & stand mounting.* Microprocessor circuit & exclusiveload cell transducer.
-
product
Axial Extensometers
6 models in this group cover tension, compression and cyclic testing Huge variety of gauge lengths and measuring ranges Cover temperatures from -265 to +200 °C (-450 to +400 °F)
-
product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.

















