ASTM
ASTM International is a globally recognized leader in the development and delivery of voluntary consensus standards, over 12,000.
See Also: E84
-
Product
AWS Probes For Ultrasonic Weld Seam Testing (ASTM)
SONOSCAN R
-
The robust ultrasonic probes with BNC connector allow a fast scanning over comparatively large areas with high precision and repeatability. Both our own and third-party wedges can be attached to our probes. . Thanks to the different types of wedges various material tests can be performed.
-
Product
Brinell Hardness Tester
-
Using a carbide ball penetrator, and applying loads of up to 3,000 kgf, Brinell hardness tester following ASTM E-10 are widely used on castings and forgings. This method requires optical reading of the diameter of ball indentation, and using a chart to convert the average measurement to Brinell hardness value.
-
Product
Parallel Plate Dielectric Test Cell
LT-4203A
-
The LT-4203A Parallel Plate Dielectric Test Cell is designed for measuring the AC loss characteristics and permittivity of solid laminates and panels per ASTM Standard D150‑98, and implements the guarded electrode (three terminal) measurement preferred as the referee method.
-
Product
Drop Tester
KD 688 A
-
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
Product
Guarded Heat Flow Meter
-
The Guarded Heat Flow Meter (GHFM-02) follows ASTM E1530-19 for testing thermal resistance and thermal conductivity of solids, such as metals, polymers and composites. The easy to operate GHFM-02 follows the trusted steady-state approach, with the addition of a guard to limit the effects of lateral heat loss. This design, allows testing of a wide range of materials with low to medium thermal conductivity.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Automated Testing Systems
-
Instron’s automated testing systems bring precision, productivity, and safety to materials testing by automating routine tensile, flexural, and compression operations. Available as full turnkey platforms or modular add-ons for existing test frames, these systems — including the AT3 three-axis, AT6 six-axis robotic, AT2 automated XY stages, CT6 cobot integration, and carousel stations — allow labs to boost throughput, reduce operator variability, and free up staff for higher-value activities. The systems are engineered to support a wide spectrum of materials (plastics, metals, films, composites, medical devices) and comply with international ASTM and ISO test standards while enhancing repeatability and workflow efficiency.
-
Product
Dial Durometer Complete Analog O-Ring Hardness Kit
OHK-1600
-
The Analog Complete O-Ring Hardness Kit is the most convenient and accurate way to perform repeatable hardness (durometer) testing on thin materials - as thin as .050". Conforms to ASTM D-2240
-
Product
Waterproof Tester by Parameter
PTTestr 35
-
Ideal for quick and accurate pH checks in pools and spas, aquariums and hydroponics operations, or anywhere frequent pH testing is required. pHTestr 30 meets requirements for many standard environmental and ASTM test methods
-
Product
Hydraulic Vibration Testers
HV-Series
-
L.A.B.’s HV Hydraulic Vibration Test Systems help you design high quality, cost-effective products and shipping containers by accurately measuring sensitivity to vibration. HV Systems are specifically designed to meet a wide range of ASTM, DOT, ISTA, ISO and federal standards for vibration testing. HV Systems are ideal for a wide spectrum of testing applications ranging from sine sweep tests to the most complex data real time simulation, or random reproduction applications.
-
Product
UL94 Horizontal & Vertical Flammability Tester
TF328
-
TESTEX Testing Equipment Systems Ltd.
UL94 Horizontal &Vertical Flammability Tester, used to determine the flammability of plastic materials for parts in devices and appliances. The apparatus is supplied as a complete system incorporating all the features necessary for ease of use safety. It conforms to all five UL 94 horizontal and vertical burner tests and associated ASTM international standards.
-
Product
Horizontal Flammability Tester
UI-TX40
-
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
Product
Automatic Extensometer
SIE-560A/560SA
-
To determine the suitability of a material for an application where it is under load, measuring its elongation is important. Measuring elongation enables determination of the elastic modulus (reversible elongation in the elastic region) by measuring the small initial elongation range, and determination of elongation at specimen failure, by measuring larger irreversible elongation in the plastic region. Shimadzu’s SIE-560A series automatic extensometers accomplish both of these measurements with high accuracy, and provide automated functions that increase testing efficiency and test reproducibility. Ideal for testing a wide variety of materials, including metallic materials, plastics, and composites, the SIE-560A series complies with ISO 527, JIS K 7161, and ASTM D638 standards for plastics tensile testing. In addition, the SIE-560A series supports strain-rate controlled metallic material tensile testing measurements specified in ISO 6892, JIS Z 2241, and ASTM E4
-
Product
Salt Spray Chambers
EBS/ECS-SERIES
-
EBS/ECS Series Salt Spray Chambers (Basic & Cyclic) are manufactured by Envisys in different versions to meet the diverse testing applications as per various international standards viz., ASTM, DIN, GM, JIS, MIL etc.,
-
Product
Child Product Safety Testers
-
AVENO children product testing instruments meet EN71, ISO 8124, ASTM F963, 16CFR 1500, requirements widely used to check if toys are safe enough for children. Including Toy Physical Properties Testers, Toy Flammability Testers, and Electronic Toy Testers.
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
Product
Charpy/Izod Pendulum Impact Tester
-
Qualitest offers a wide range of pendulum Charpy / Izod impact testers for tests according to the relevant test standards such as ASTM D256, ASTM D6110, ISO 179, ISO 180, as well as other DIN, ASTM, and ISO standards. These pendulum Izod / Charpy impact testers cover a range from 0.5 Joules to 50 Joules, and we can even go up to 800 Joules with the models in the Metals category. The Plastics Pendulum Izod / Charpy Impact Testers are available in a variety of models, e.g. for instrumented or non-instrumented tests, with analog or digital displays and with a range of different options especially made for your tests.
-
Product
Pinhole Detector
NOVOTEST ED-3D
-
NOVOTEST ED-3D Pinhole Detector was designed for rapid non-destructive testing of the continuity of coating (e.g. porosity of film) with thickness up to 500mkm according to ASTM G62-A.Pinhole Detector is designed for testing the porosity of partially painted places and other discontinuities of protective dielectric coatings on metal products by putting low voltage through a sponge which is soaked in a liquid electrolyte with high penetrating properties.
-
Product
Walk-In Solar Panel Test Chamber
-
For testing various size Walk in Solar Panel Test Chamber WIEBER designs and manufactures Walk in Solar Photovoltaic Testing Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes.
-
Product
Conductivity Type Tester
HS-HCTT
-
It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.
-
Product
Automatic Softening Point Tester
LD-LSPT-A10
-
Automatic softening point testerLD-LSPT-A10is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
-
Product
Brinell Hardness Tester
KB Series
-
Newage Testing Instruments, Inc.
The Newage KB Series is a popular, manually-controlled Brinell hardness tester that meets ASTM E-110. This lightweight, portable tester is ideal for virtually any size or shape of metal specimen.
-
Product
45 Degree Flammability Tester
-
TESTEX Testing Equipment Systems Ltd.
45 Degree Flammability Tester, to determine fabric flammability under controlled conditions total automatically(fabric burn test). 45 Degree Flammability Tester complies with ASTM D1230, CALIF TB117, FTMS191-5908, etc. Our product is the best choice for you when you do flammability test for fabric in flammability testing labs.
-
Product
Portable Hardness Tester
Magnetic Type QualiMag Series
-
The Portable Hardness Tester - Magnetic Type QualiMag-R - Magnetic Rockwell Hardness Tester Rockwell test head fixes to the surface of iron and steel parts to test the hardness by applying magnetic force. Meant to replace Leeb hardness testers which are not as accurate nor reliable. Use the Portable Hardness Tester - Magnetic Type QualiMag-R - Magnetic Rockwell Hardness Tester on steel parts, steel plates, steel pipes, forgings, large to medium sized heat treated parts(if surface available), welding joints, pressure vessels, etc. The Portable Hardness Tester - Magnetic Type QualiMag-R - Magnetic Rockwell Hardness Tester Rockwell complies with Standards ISO 6508 and ASTM E18.
-
Product
Quick Change Probes For Weld Seam Testing (ASTM)
SONOSCAN Q
-
In addition to angle beam probes according to european standards (EN), we offer probes with quick-change wedges for ultrasonic weld seam inspection as well as various wedges for the american market. Quick-change probes are used wherever access to the inspection object is difficult to reach with the larger AWS transducers. The relatively small, round elements also offer better defect resolution.
-
Product
Force Calibrating Machines
-
Morehouse Instrument Company Inc.
Morehouse Universal Calibrating Machines (UCM) are an easy to use, cost-effective, hydraulic force calibration system that lasts for generations. UCMs built in the 1950s are still operating today! The UCM can be used to calibrate both tension and compression instruments in accordance with ASTM E74, ISO 376, and other internationally recognized force standards.
-
Product
Ozone Test Chamber
EKT-2001OZ-HCSTX
-
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
Product
SUNTEST
XXL+
-
Atlas Material Testing Solutions
The Atlas SUNTEST XXL+ is a large xenon lamp weathering and lightfastness test chamber meeting various ISO, ASTM, and ICH industry standards. Its horizontal 3000 cm2 exposure area is best-in-class for 3-D specimen testing.
-
Product
Leather & Shoes Test Machine Series
-
Shoes Testing Equipment products is use for shoes bending , footwear tensile , shoes leather DIN abrasion, leather shoes scratch ,folding flexing of test items and meet UL, ASTM, JIS, GB, ISO, TAPPI, EN, BS and other domestic and international standard...
-
Product
Elemental Analyzers
-
Bruker manufactures instruments for elemental analysis from 100% down to the sub-ppb trace level. Easy-to-use solution packages help customers in process and quality control to meet industry norms and standards including ASTM, DIN, ISO and FDA. Highest analytical accuracy and precision enable academic research from lab to field.
