-
Product
PXI Solid State Multiplexer, Single 6-Channel, 30 Amp
40-667B-012
Multiplexer Module
The 40-667B-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
DC to 2 GHz Power Splitter with BNC connector
11667L
Power Splitter
The Keysight 11667L is a 50 ohm two-resistor type power splitter with BNC connectors. It is used with the E5061B network analyzer for power distribution network applications, such as DC-DC converter output impedance measurements with shunt-thru method (100 Hz to 10 MHz). It provides excellent amplitude (<0.2 dB) and phase tracking (+/-3), ensures highly accurate power splitting and low SWR minimizes measurement uncertainty.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 10 A
40-666B-012
Multiplexer Module
The 40-666B-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
1,500-Watt AC/DC Power Supply, Air Plenum
56WS1-01
Programmable Power Supply
NAI’s 56WS1-01 is an air plenum-cooled, 1,500 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single +28 VDC output at 1,500 Watts continuous or 3,000 Watts peak. This standalone device converts aircraft power so it can be used by system components.
-
Product
Solid State Relay
5200
-
The B/W 5200 Series solid state relays are offered in two basic types for use in a wide range of low and high sensitivity applications.Both 5200 solid state relays are designed to operate on either 115 or 230 volts AC at 50/60 hertz.Both models incorporate a low voltage sensing circuit.Furhtermore, both solid state relays are capable of performing control functions directly from electrodes suspended in a well or tank, the B/W Unifloat level sensing system, or various pilot devices such as pressure, flow and limit switches, thermostats and push buttons.
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9322A
Power Sensor
The E9322A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
Product
10 MHz to 18 GHz LAN Wide Dynamic Range Average Power Sensor
L2052XA
Power Sensor
The Keysight L2052XA is a fast, accurate and wide dynamic range 10 MHz – 18 GHz LAN average power sensor.
-
Product
Solid State Gas Detectors
SMC 20X/200X
-
The SMC 20X/200X are single-gas detectors used to monitor combustible gas, hydrogen sulfide (H2S) or carbon monoxide (CO). The detectors are based on solid-state technology, a simple and robust method of detection capable of detecting low parts-per-million (ppm) levels of gas.
-
Product
Mini Power Contact, ITA, 65 Amp, 8 AWG
610115125
Power Contact (ITA)
Primary mating contact 610116112. (May mate with other Receiver contacts, as well.)Mini Power contacts carry up to 65 amps continuous current, 480 VAC. Maximum resistance is 1 Milliohms.
-
Product
400W 6U CompactPCI Hot-Swappable Redundant Power Supply
cPS-H640/AC
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 6U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 400 W DC output
-
Product
2-26.5 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5026
Amplifier
The HMMC-5026 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-26 GHz frequency range. Typical applications of the HMMC-5026 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-26 GHz frequency range.
-
Product
PXI/PXIe Solid State Attenuator, Hex, 6GHz, 50Ω, SMA
41-182B-006
Attenuator
The 41-182B-006 (PXI) and 43-182B-006 (PXIe) are programmable RF attenuator modules with 6 channels in 2 slots capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuator uses solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
RF Power Amplifiers
-
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
-
Product
PXI 4 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-021-64X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
DC Power Supply, 6 V, 5 A, 30 W
E36102B
DC Power Supply
The Keysight E36102B is an accurate, 6 V, 5 A, 30 W compact power supply for your bench or system.
-
Product
Amplifiers
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
PXI/cPCI Programmable Power Supply - 16-bit Read Back Voltage and Current at Output
52912
Programmable Power Supply
Chroma 52912 programmable DC power supplies are designed specifically for test applications that demand precision output voltage/current and tightly coupled measurement capabilities.
-
Product
DC Power Supply, 0-120 V, 0-1.5 A, 180 W, GPIB
N6700
DC Power Supply
Keysight high performance DC power supplies offer speed and accuracy for test optimization. The single output, 200 W, GPIB 6641A-6645A provide fast, low-noise outputs; analog control of output voltage and current; fan-speed control to minimize acoustic noise; as well as parallel and series connections of multiple units.
-
Product
Advanced Power System - Dynamic DC Power Supply, 40 V, 25 A, 1000 W
N7952A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Regenerative Power System, 2000 V, ±30 A, 20 KW, 400/480 VAC
RP7973A
DC Power Supply
The RP7973A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
Thermocouple Power Sensors
N8487A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Custom Configured MPS, 600W
N6711C
Power Supply
The Keysight N6711C is a 600 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6711C consists of 1 N6701C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6711C.
-
Product
PXI Solid State Multiplexer, 10 Amp, Dual 3-Channel
40-666A-011
Multiplexer Module
The 40-666A-011 is a dual 3-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
DC Power Supply, 35 V, 1 A, 35 W
E36104B
DC Power Supply
The Keysight E36104B is an accurate, 35 V, 1 A, 35 W compact power supply for your bench or system.
-
Product
RF Medium / High Power Amplifier
-
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
Product
Amplifiers
-
Is an electronic device that can increase the power of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output.
-
Product
Amplifier
AC-100
-
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A
40-667C-012
Multiplexer Module
The 40-667C-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
RF Power Amplifiers < MMICS
-
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
