-
product
PXI Ultra High Density Reed Relay Matrix, 66x8, 1-Pole
40-541A-021
The 40-541A-021 is part of a range of ultra high density matrices. The 40-540A/541A/542A are the world’s highest density single slot PXI reed relay matrix modules and are available as a 132x4, 66x8 or 33x16 matrix with 1-pole switching.
-
product
Diagnostic Relay Buddy 12/24
192
Relay Buddy 12/24 is a quick go / no-go tester for the most common automotive relays. This new version Relay Buddy tests both 12 and 24 volt relays. If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
product
Phase Monitoring / Potential Selector Relay
This is a phase failure relay suitable for 3 phase supplies. The relay is designed to automatically change over from the primary supply to the secondary supply if any phase of the primary supply has faulted.
-
product
PXI Mixed Configuration Relay Module - 8 Cells Populated
40-138-AA-BB-CC-DD (8 CELL)
The 40-138 2A Relay Module with 8 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 40 GHz, 50 Ω, SMA-2.9, External Termination, Failsafe, Remote Mount
40-781A-522-E
The 40-781A-522-E (PXI) and 42-781A-522-E (PXIe) are dual failsafe SPDT 40 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
PXI 13 x DPDT Power Relays
40-130-102
Pickering Interfaces 40-130 DPDT Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. It is available in a choice of 8 and 13 relay versions and has voltage handling up to 220VDC/125VAC and current handling to 2A . Connections are made via a front panel mounted 50 or 78 pin D-Type connector.
-
product
Relay Test Equipment
MC3000 Series
MC3000 is recently developed relay test equipment. There are 3 sub-models, MC3000A, MC3000B and MC3000C. They are low cost oriented, aimed to provide customers cheap and cost-effective products.
-
product
32 Channel Relay Output Switch
DP-VME-4224
DP-VME-4224 is a 32 Channel Relay Output Switch. Applications for this module includes hardware simulation, digital simulation, high-reliability systems, and automatic test equipment, and relay output for soft PLCs.
-
product
Relay Data Emulator™
SUBNET SEL
SUBNET SEL Relay Data Emulator Software can automatically learn a SEL relay’s communication capabilities. SUBNET SELRDE Software can then be directly substituted for the physical SEL relay to safely and reliably commission relay communications. Effortlessly change target and meter data through SUBNET SELRDE Software without the inconvenience or risk of physically jumpering contacts or using expensive and often unavailable test sets to directly inject voltage/current.
-
product
4 Relay Channels, Non-latching
RY1
The RY1 module features 4 individual single-pole, user SPDT Form-C (changeover/break-before-make type) relays (channels). Each channel has a common input terminal (C), a normally closed output terminal (N/C), and a normally open (N/O) output terminal. The channel either energizes or de-energizes the relays (close or open) so that the signal provided on (C) may be switched/directed to either the (N/C) or (N/O) terminals.
-
product
Earth Leakage Relay
Nippen Electrical Instruments Co.
NIPPEN's Earth Resistance Testers are used for measuring earth electrode resistance, soil resistance, earth continuity, neutral and earth loop resistance, resistance of various components etc.They are used in Railways, Defence, Utilities, Power Plants, Geological Surveys and other Industries.Direct reading type models SET/DET/TET provide direct readings of resistance on moving coil type meters, having a linear scale, 70mm long knife edge pointer and an external zero adjustment.
-
product
Relay Output Board
VME-2232A
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
product
Electromechanical Relay Switches
SMA SPDT electro mechanical RF relay switch features Indicators, Failsafe, Normally Open with an isolation minimum of 60 dB. SPDT electromechanical relay radio frequency switch PE71S6052 is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our SPDT SMA coaxial RF relay electromechanical switch can ship worldwide the same day that it is bought as with our other available RF parts.
-
product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors, With Interlock
42-158-002-HI
The 40/42-158-002-HI is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-780B-522-E
The 40-780B-522-E (PXI) and 42-780B-522-E (PXIe) are dual failsafe SPDT 18 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
PXI Single 16 to 1 RF MUX MCX 75 Ohm
40-835-101
The 40-835-101 is a single 75 Ohm 16-channel RF MUX in a single PXI slot. The module has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40-835 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
Ultra High Density 4mm Reed Relays
120-1-A-5/1
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A5 V Coil
-
product
Universal Three-phase Protective Relay Test Set
Mentor-12
The Mentor 12 is the most advanced three-phase relay test set available for type and field testing of electromechanical and digital protections of any kind, in traditional or IEC-61850 based substations.
-
product
General Purpose Switching PXI Card
GX6325
The GX6325 is 6U switching card with 75 SPDT Form C relays with a switching power rating of 60 W. Featuring the highest density available in PXI for this type of switch card, the GX6325 is suitable for all test applications requiring general purpose, low level switching.
-
product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors
42-153-002
The 40/42-153-002 is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A. User connection is via 2x50-pin SGMC male connectors.
-
product
PXI/PXIe Microwave Relay, Triple SPDT, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-780B-543
The 40-780B-543 (PXI) and 42-780B-543 (PXIe) are triple failsafe SPDT 40 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
LXI Reed Relay Matrix - Single 128x4 Plugin, Direct Y Access, 6 Analog Buses
65-221-012
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
PXI 16 x SPST Reed Relay
40-115-021
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
product
Relay Testing Voltage Source
PTE-FCL
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCL upgrades the PTE-100-C to the PTE-100-C Plus model.
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
PXI Triple Microwave SPDT Relay 2.5GHz 75 1.6/5.6
40-780A-753
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PCI 32 Channel Reed Relay Output Digital Interface
8007
The 8007’s PCI digital I/O interface reed relay outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
product
Ethernet Controlled Relays And Relay Drivers
*ICS's Ethernet to Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Ethernet to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE or with RPC commands from any Linux/Unix or MAC computer. Use ICS's interactive VXI-11 Keyboard program for easy operation from your PC without having to write a program.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 12.4GHz, 50Ω, N-Type
40-780B-511
The 40-780B-511 (PXI) and 42-780B-511 (PXIe) are single SPDT 12.4GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
SUPER-LIGHT Protection Relay Testing Equipment
L336i
Protection Relay Testing Equipment has long been associated with the heavy weight and the large size. So carrying the relay testing set to work site seems to be the job of engineers who are physically strong.
