6U PXI Chassis
See Also: PXI Chassis, 3U PXI Chassis, Portable PXI Chassis
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
-
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
Desktop/Wallmount Edge-Server Chassis For MATX/ATX Motherboard
HPC-5422
-
Supports mATX/ATX motherboardSupports up to two 3.5" HDDs or one 3.5" HDDs with dual 2.5" HDD TraysSupports ATX3.0 PS/2 Power SupplySupports up to five FHFL expansion slots2 x12cm system fansSupports one high-end GPU card
-
Product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 8-slot BRIC Matrix, 840x6, 1 Pole (10 Sub-cards)
40-558-801-840x6
-
The 40-558-801-840x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 150x4 2A 1-Pole Matrix
40-568-102
-
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 12-Slot BRIC Matrix, 396x4 1-Pole (9 sub-cards)
40-562B-321-396X4
-
The 40-562B-321-396X4 is a high density BRIC12 matrix module with a size of 396x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 132x16 1-Pole (12 sub-cards)
40-562B-321-132X16
-
The 40-562B-321-132X16 is a high density BRIC12 matrix module with a size of 132x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Ultra High Density 64x4 2-Pole Matrix
40-533B-022
-
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
Product
PXIe-8842 2.6 GHz 6-Core Processor PXI Controller
787882-0118
-
The PXIe8842 is an embedded controller for PXI systems that you can use for processor-intensive modular instrumentation and data acquisition applications. The PXIe8842 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, one Thunderbolt 4 port, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-03
-
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
PXI Dual Microwave SPDT Relay 12.4GHz 50 N-Type
40-780A-512
-
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PXI Dual 2 x 2 Insert/Bypass Switch FC/PC
40-860-122
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
VME64x Form Factor Extender, 6U x 180mm, w/o P0
116FFE6018-0125R
-
The VME64x form factor extender 6U 180 mm without P0 allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
PXI 8-Slot BRIC Matrix, 242x8 1-Pole (11 sub-cards)
40-562B-121-242X8
-
The 40-562B-121-242X8 is a high density BRIC8 matrix module with a size of 242x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Chassis Slide Rail Size 5
CAE010393
-
Securely locked in extended position. The chassis/cabinet mounted slide rails are ultra rugged and hold significantly more weight and can withstand shock and vibration in harsh environments.
-
Product
PXI Dual 12x8 Matrix, 1 Pole Switching
40-522-021
-
Medium density PXI dual 12x8, 1-pole matrix - it is also available inreed relayformats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable forswitching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems.The two banks may be used for operating a 4-wire measurement system (bank-1 for source,bank-2 for measure). Larger matrices may be constructed by daisy chaining the commonsignals from multiple PXI Modules.
-
Product
PXIe-6612, 5 V, 8-Channel PXI Counter/Timer Module
782352-01
-
PXIe, 5 V, 8-Channel PXI Counter/Timer Module—The PXIe‑6612 performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6612 can perform three simultaneous high-speed DMA transfers.
-
Product
PXI 32 x SPDT Electromechanical Relays
40-148-001
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI 8 Slot BRIC 105x16 1-Pole (7 sub-cards)
40-561A-121-105X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
VPX Chassis 4U/84HP 8 Slots
BKP3-CEN08-15.2.15-4
-
This 8 slot Hartmann Open VPX BKP3-CEN08-15.2.15-4 profile system chassis provides an intelligent, practical packaging solution for high-performance processors. The 84HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with either a 600W ATX or 600W plug-in VPX power supply and a 1U removable, bottom mount fan tray.
-
Product
CTEL 6U 8 slot with ATX, P1P2P4s, P3P5l, RoHS
104CTEL608-4146R
-
CompactPCI CTEL 6U 8 slot with system slot left, H110 bus, ATX connector, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
Product
PXI Dual 16 Channel Switch Simulator
40-485-321
-
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
PXI RF Multiplexer Switch Module
-
PXI RF Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI RF Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 925Ω
40-252-021
-
The 40-252-021 is a programmable resistor module with 2 channesl which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Dual Transfer Switch 26.5GHz 50Ω SMA
40-782-532
-
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
PXI 8-Slot BRIC Matrix, 77x16 1-Pole (7 Sub-cards)
40-562B-121-77X16
-
The 40-562B-121-77X16 is a high density BRIC8 matrix module with a size of 77x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Mixed Configuration Relay Module - 11 Cells Populated
40-138-AA-BB-CC-DD (11 CELL)
-
The 40-138 2A Relay Module with 11 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-321-HI
-
The 40-230-321-HI (PXI) and 42-230-321-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 395kΩ
40-298-142
-
The 40-298-142 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI MultiComputing Remote Control Module
-
PXI MultiComputing Remote Control Modules enable PXI systems to transfer data at multigigabytes per second with only a few microseconds of latency. You can use these models in applications such as real-time tests, hardware-in-the-loop (HIL) tests, and structural tests that need a large number of distributed PXI systems to share data with low latency.
