PXI Express
Bi-directiona data throughput up to 6 GBytes per sec and electro-mechano interoperability with CompactPCI Express.
See Also: PXIe, CompactPCI Express
-
Product
PCI Express 2-Port
7203e
-
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
PXI High Density Multiplexer, 1-Bank, 80-Channel, 1-Pole
40-615A-018
Multiplexer Module
The 40-615A-018 is a 1-bank, 80-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-01
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
CPCI or PXI DPFS Board
MS 1830
-
- Configurable Frequency Ranges from 100Hz to 1MHz- Resolution insteps of 0.03Hz- Duty Cycle 50%- Amplitude of the Digital Frequency out : Low – 0.4V max, High – 4.8V min- Rise/Fall Time (for a 15pF Load) is typically 5 ns- Amplitude of the Analog waveform out : Low – 0.4V max, High – 4.8V min- Sinusoidal or Square Wave Output (Configurable)- Differential / Single Ended Output (Configurable)- Frequency on each of the 8 Channels are individually Programmable- Hot Swap Facility for live insertion and removal of the board- Facia plate with Micro Switch Assembly, provided for proper insertion / easy removal of the Board- BNC Connector Interface for Signal Output at the front panel- Each Output Channel is driven by a Cable Driver to drive 8m of Coaxial Cable- Driver interface for Windows XP/VISTA/7 and LINUX OS
-
Product
Single 24x6 1-Pole High-Density PXI Matrix Module
40-520-302
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 10A Power MUX, 5-Bank, 6-Channel
40-661-005
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
-
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
Product
PXI Vector Network Analyzers
Vector Network Analyzer
Our PXI vector network analyzers (VNAs) perform fast, accurate measurements and reduce your cost-of-test. Simultaneously characterize many devices — two-port or multiport — using a single PXI chassis. By combining independent, two-port network analyzer modules into one chassis your multisite, multi-DUT, and multiport test applications scale flexibly. Use all ports to simultaneously measure your devices with multiport error correction.
-
Product
PXI Temperature Input Module
Module
PXI Temperature Input Modules offer up to 32 channels of analog temperature measurements. Some models include autozero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples, while others support 2-, 3-, or 4-wire resistance temperature detector (RTD) measurements. PXI Temperature Input Modules support both high-speed and high-resolution modes. You can program channel configurations and scale measured data into engineering units.
-
Product
Dual 12x8 1-Pole High-Density PXI Matrix Module
40-520-206
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI MUX 1-Bank of 80 Channel 1-Pole
40-615-021-1/80/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI RTD Simulator Module, 24 Channel, PT1000
40-263-003
Simulator
The 40-263-003 is a 24-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
ADLINK PXI Platform Services (APPS)
Platform
Software framework services and drivers fully support PXI-2 and PXI-6 software specifications
-
Product
96-CH 12-Bit 3 MS/s High-Density Analog Input PCI Express Card
DAQe-2208
Analog Input Module
ADLINK DAQe-2208 is an high-density and high-performance analog input card. The device can sample up to 96 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 48 AI channels in order to achieve maximum noise elimination.
-
Product
PXI-5670, 2.7 GHz PXI Vector Signal Generator
PXI-5670 / 778768-01
Vector Signal Generator
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
Product
PXI 36x12 Matrix Module, 1-pole 2A 60W
40-578-001
Matrix Switch Module
The 40-575/576/577/578/579 are a range of high density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PCIe-6320, PCI Express, 16 AI (16-Bit, 250 kS/s), 24 DIO Multifunction I/O Device
781043-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 250 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6320 offers analog input, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6320 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI 2A Multiplexer 158-Channel 1-Pole
40-611-001
Multiplexer Module
The 40-611 Very High Density multiplexer module is available in 158-Channel 1-Pole or 79-Channel 2-Pole configurations. Both configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express Timecode and GPS Reader Generator
PCIEX-SyncClock
-
The PCI-Express time code reference timing card with standard options such as IRIG B and optional GPS receiver provides an extremely accurate time source to the PCI-Express bus.
-
Product
16 Port PCI Express
PEX 8619
-
The ExpressLane™ PEX 8619 offers 16 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 16 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8619 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
PXI 3x3 10GHz Matrix with Loop-Thru & Term
40-787-518-3X3-L-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI Test System Dev, Debug & Monitor Software
InstrumentStudio
Test System
InstrumentStudio is free application software that provides an integrated approach to interactive PXI measurements. InstrumentStudio helps you to unify your display, export instrument configurations to code, and monitor and debug your automated test system. You can view data on unified displays with large, high-resolution monitors, and then capture multi-instrument screenshots and measurement results.
-
Product
PXI
-
LinkedHope Intelligent Technologies Co.,Ltd.
PXI systems are composed of three basic components — chassis, system controller, and peripheral modules.
-
Product
MiniPCI Express to USB 3.x Adapter
SKU-089-14
-
MiniPCI Express to USB 3.x Adapter allows connection M.2 modules with M.2 (B key) to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits and supports USB 3.x, USB 2.0 interfaces.
-
Product
Analog Optical Power Meter - PXI
Power 1500 Series
Power Meter
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
PXI Dual Transfer Switch 40GHz 50Ω SMA-2.9
40-782-542
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
97 lane, 25 port, PCI Express
PEX 9797
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
PXI Single 2 Channel Optic Mux FC/PC
40-855-112
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Power Multiplexer, 18-Channel, 1-Pole
40-665A-001
Multiplexer Module
Model 40-665A-001 is a 18-Channel 1-Pole Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions).
