-
Product
Isolated Digital Input and Relay Output Card
104-IIRO-8
-
The 104-IIRO-8 is a low-cost card that provides isolated input and output for PC/104 Bus computer applications. The card has eight optically-isolated digital inputs for AC or DC control signals, eight TTL Inputs and eight electro-mechanical relay outputs. An Economy version can be ordered as Model 104-IIRO-8E which has no Change of State Detection or IRQs.
-
Product
Low Noise Voltage Preamplifier
1201
-
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
-
Product
OHMMETERS
DOT-1000-2
-
Model DOT-1000-2, is an ac four-terminal ohmmeter to be used for the measurement of dynamic ac resistance of batteries, fuel cells and other voltage sources.
-
Product
Analytical Balaneces
AT-R Series
-
Basic Model with Improved Convenience.*Freely set responsiveness or stability*Connect with a computer via USB or RS232C*Perform stable measurements in combination with an ionizer
-
Product
Field Strength Meters
-
The FSM series of field strength meters will measure the strength of a RF signal appearing at its input from +20 dBm to -110 dBm for wide bandwidth models and +10 dBm to -120 dBm for narrow bandwidth models. The RF strength will be displayed on an LCD display to an accuracy of ±3 dB over the entire 130 dB dynamic range. A matching field signal generator is also available to act as a signal source for propagation studies.
-
Product
UV Fluorescence SO2 Analyzer
Model N100
-
Teledyne Advanced Pollution Instrumentation
The Model N100 instrument uses the proven UV-fluorescence principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of low-level Sulfur Dioxide (SO2) gas.
-
Product
Autoranging System DC Power Supply, 500 V, 60 A, 10000 W, 400 VAC
N8948A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
Light Sheet Microscopes
-
Life science research can place high demands on your imaging capabilities: Sometimes you need to image whole living model organisms, tissues and cells as they develop. Or you may want to observe subcellular dynamics in living samples over hours and even days. Light sheet fluorescence microscopy (LSFM) with its unique illumination principle is ideal for fast and gentle imaging of such specimens.
-
Product
Multi-Parameter Controller
8900
-
The Signet 8900 Multi-Parameter Controller takes the concept of modularity to the extreme. Each 8900 Controller is field-commissioned with the users-specified combination of inputs, outputs, and relays using simple-to-install modular boards into the base unit. Configure the system by selecting either two, four, or six input channels which accepts any of the Signet sensors listed below, and/or other manufacturer's sensors via a 4 to 20 mA signal converter (Signet Model 8058). To complete your unit, choose a power module with universal AC line voltage or 12 to 24 VDC.
-
Product
DC Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
DC load banks for all voltage levels and power test applications, available in a variety of models including portable and fixed models.
-
Product
3D And 2D Visualization Software
3DViz
-
The 3DViz software provides intuitive 2D and 3D visualization of high-definition sensor data. Software allows strain or temperature data from an ODiSI system to be visualized directly on a 3D CAD model or a 2D image.
-
Product
Electronic Printers
EP-100/EP-110
-
Easy-to-Use Printers, Supporting Good Laboratory Practice The EP-100 and EP-110 electronic printers for Shimadzu balances are easy-to-use, provide time and signature information, and support Good Laboratory Practice (GLP). Supported balance models include: AP; AW-D, AUW, AUX and AUY; ATX and ATY; AT-R; UP; UW and UX; TX; TXB; BL; ELB; BW-K and BX-K; and the MOC63u moisture balance.
-
Product
Line Loop Tester
8455
-
Simpson?s Model 8455 Line Loop tester detects line shorts, opens and multiple ringers, DC voltages and loop resistance. It can measure DC voltage up to 100 volts and loop resistance to 2 megohms. A front panel ?reverse polarity? switch allows changing polarity positions quicker and easier than manually switching test leads when making line checks.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - PCIe
Model 78620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user-configurable gigabit serial interface- LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
2U 4 Slot VME64 Mini Crate
VME8004B
-
The Model VME8004B is a 4 slot VME crate, suitable for 6U x 160mm boards, with VME64 compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V. The VME8004B provides automatic daisy chain and supports CBLT data cycles.
-
Product
NI Electric Motor Simulation Toolkit
-
PMSM, ACIM, SRM, and power inverter models for high-performance simulationHigh-fidelity simulations with support for user-defined parameter lookup tables or JMAG-RT models. Open software for full flexibility and customizationLabVIEW project templates to build a software-only simulation and hardware-in-the-loop application. Direct integration with NI VeriStand for configuration-based real-time test. Models for desktop simulation, LabVIEW Real-Time simulation, and FPGA-based simulation
-
Product
Tap Changer Analyzers & Winding Ohmmeters
-
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
Product
Reciprocating Pumps
ReaXus
-
Teledyne LABS ReaXus® reciprocating pumps covers a broad range of application needs, ranging from 5 mL/min to 300 mL/min and up to 6,000 psi. Whether you need low pulsation or are working with hazardous materials, the ReaXus line has an option for you. The single piston models are targeted towards moving material or providing pressure. The dual piston models are focused on continuous processing applications where a steady flow of material is important.The ReaXus product line is low maintenance and requires no calibration like other styles of pumps, saving your organization time and money.
-
Product
AC Load Bank
-
PC software controls offer advanced load profile solutions and model options range from small, portable, low-power units, to high-power indoor or outdoor permanent load solutions.
-
Product
GPS Simulator
MVT-NSSG
-
The Navigation Spread Spectrum Generator can be used for precise GPS M-Code interference tests with existing GPS C/A and P/Y receivers. The simulator is capable of generating all the current GPS signals simultaneously with the new modernized signals and codes. Optional models can be configured with unique user defined signals, such as would be required for GLONASS.
-
Product
Universal Amplifier Heatsinks
-
A universal heatsink, which is designed and fabricated for Eravant's active device applications with up to 15-watt power dissipation. The heatsink consists of the main heatsink body, a DC fan and a heat spreader. The heat spreader is also known as adapter, which is used to bridge the mounting gap between the heat sink main body and the to-be-heat-sunk devices, such as power amplifier, frequency active multiplier, oscillator, transmitter and transceiver due to various mounting hole locations. The heat spreader offers various mounting patterns to accommodate more than 15 product models. This heatsink is not only designed for Eravant's standard products and Uni-Guide™ featured products, but also for many industrial standard microwave and millimeter wave products offered by other manufacturers. Other heatsinks with different power dissipation capacities are offered under different model numbers.
-
Product
Total Hydrocarbon Analyzer
Model 4030
-
Teledyne Analytical Instruments
The Model 4030 uses a field proven FID detector in a heated chamber. The chamber is heated to a high temperature to meet US EPA requirements for VOC emissions monitoring.
-
Product
Aerosol Neutralizer
3077A
-
The Aerosol Neutralizer model 3077A is a general-purpose radioactive neutralizer suitable for use with highly-charged and/or highly concentrated aerosols. The Model 3077A can be used with flows up to 5 L/min. If your flow rate will always be significantly higher than this, consider model 3012 and/or 3012A. If your particles will not be highly-charged and/or highly concentrated, consider model 3077.
-
Product
Signal Generators
ZTX-Series
-
RPG's Signal Generator Extenders allow high performance frequency extension of microwave sources into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. These modules combine high test-port power with low phase noise to offer exceptional performance. Contact RPG to discuss Signal Generator Extenders configurations that will gain the best performance for your application.
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - XMC
Model 71141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/Ds- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction cooled versions available- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Water Treatment Plant Analyzer
Aqualog
-
Aqualog® is the only instrument to simultaneously measure both absorbance spectra and fluorescence Excitation-Emission Matrices. EEMs are acquired up to a 100 times faster than with other instruments. Dedicated software automates traceable Quinine Sulfate Unit calibration and correction of inner-filter effects and Rayleigh and Raman scattering lines, enabling rapid export to modeling algorithms like PARAFAC.
-
Product
10-amp AC and DC Variable Power Supply
ACDC-10
-
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
Product
Model Based Design and Simulation
-
Requirements validation through simulation and autogeneration of embedded systems
-
Product
Stroke-to-Raster Scan Conversion
SSC/924
-
The Model SSC/924 Stroke-to-Video Scan Converter converts stroke video from XYZ vector to a standard video format. Stroke video is generated by a variety of random deflection devices, including certain radar and sonar devices, spectrum analyzers, and Heads Up Display (HUD) generators. High Definition, Standard Definition, and VESA video output standards are provided. After conversion, the video can be recorded using standard video recording devices and viewed using low cost, off-the-shelf monitors.
-
Product
Data Collection and Analysis System
3002
-
The Model 3002 SER System is a state of the art data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER) data in conformance with PRC-002-1 and PRC-018-1.
