-
Product
Hydrogen Penetration Monitoring System
MS3112
-
The Hydrogen Penetration Monitoring System™ provides a method for directly measuring the rate of hydrogen migration through a vessel or pipe wall. This method actually measures the penetration current set up by the hydrogen as it moves through the steel. By sensing and recording this data directly from the pipe wall, this system offers valuable data which can only be indirectly inferred by other methods.
-
Product
NanoModeScan M² Measuring System
-
This scanning slit M² measurement system accurately analyzes lasers with wavelengths from UV to Far Infrared with its silicon, germanium, or pyroelectric head. It features a compact portable design, immediate results, ISO compliant measurements, and operates in CW or kHz Pulsed modes which makes it ideal for comprehensive analysis of lasers of most wavelengths.
-
Product
Systems Analysis Interface
Saint2
-
The Systems Analysis INterface Tool 2, a Delphi Preferred Tool, for Low-cost EOL Testing & Reflashing Without the Need of Additional Hardware.
-
Product
Personal Logging Dosemeter System
05NK004
-
Measure personal noise levels with the Logging Dosemeter System. Kits consist of either 1 or 5 logging dosemeters with calibrator and case. Ideal for checking worker's exposure to noise, downloading data to a PC and storing the results for future evaluation.
-
Product
Probe System for Life
PS4L
-
The Probe System for Life, or PS4L, is SemiProbe’s patented adaptive probe system architecture. Unlike traditional probe systems, all of the basics components of our systems, including the bases, stages, chucks, microscope mounts, and manipulators, are interchangeable, upgrade-able, and configurable. The PS4L Adaptive Architecture ensures and optimal test configuration for each individual customer application.
-
Product
Hall Effect Measurement system
HMS-3000
-
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Product
Test And Measurement System
TM400
-
The TM400 system was designed to provide the ideal link between calibrated test microphones and measurement equipment such as SIM®, SIA SMAART Live®, TEF® or other systems. By using a radio link, long cables can be eliminated thus saving time and providing opportunities for additional measurements to increase accuracy. The microphone can even be moved around in the venue while the audience is present – something that is impossible with a cabled measurement microphone.
-
Product
Complete Data Acquisition System
ScopeLogicDAQ
-
ScopeLogic - complete data acquisition system - consists of Digital Oscilloscope and Logic Analyser. This small instrument is making the accurate analysis of complex analog-digital signals possible - thanks to simultaneous sampling finding relationship between these signals is easy. The user is able to simultaneous use 16 digital channels and 2 analog channels with standard scope probes.
-
Product
CrystalCalHP Calibration System
-
AMETEK Sensors, Test & Calibration
This portable gauge and transmitter calibration system is 7 to 10 times faster than a deadweight tester. It allows you to do a 10 point up and down calibration in less than 3 minutes including printing out a calibration certificate.
-
Product
Benchtop Research System
XENON X-1100
-
The XENON X-1100 is the only low-cost benchtop Pulsed Light system that enables researchers to more easily characterize new processes using XENON’s proven technology.
-
Product
Nuclear Safeguard Systems
-
Nuclear Safeguards are measures to verify that States comply with their international obligations not to use nuclear materials (plutonium, uranium and thorium) for nuclear explosives purposes. Global recognition of the need for such verification is reflected in the requirements of the Treaty on the Non-Proliferation of Nuclear Weapons (NPT) for the application of safeguards by the International Atomic Energy Agency (IAEA). Also, the Treaty Establishing the European Atomic Energy Community (the Euratom Treaty) includes requirements for the application of safeguards by the European Commission. Organizations such as the IAEA and EURATOM and others are tasked with ensuring declared amounts of material are indeed present in the facilities in which they are stored and that such material is not being diverted to other uses.
-
Product
Modular SEC system
SC2000
-
The new Postnova SC2000 Modular SEC system offers unrivalled flexibility in Advanced SEC/GPC analysis. It is the first truly modular multi-detector SEC system available allowing flexible access to a wide range of applications. The system incorporates state-of-the-art detection technologies including light scattering (MALS > multi-angle light scattering) for absolute molecular weight and Viscosity detection for structural and conformational data. Many other detector and accessory options and combinations are available to build a system uniquely tailored to your application requirements, with the benefit of modularity to allow easy future expansion. In addition, the SC2000 can be further expanded to include FFF modules to widen the application range and allow both SEC and FFF separations to be carried out on the same sample within one instrument platform.
-
Product
Vehicle Tracking System
-
Information System Technologies Inc.
ISTI has built a vehicle tracking system that overcomes the challenges with acoustic tracking and localization of small ground and airborne vehicles using low-cost wireless sensor nodes. The sensor-level sub-band feature extraction and streaming of the encoded data enables real-time direction of arrival (DoA) estimation and tracking even for large wireless sensor networks with limited bandwidth. Benefits include: accurate tracking of single or multiple closely spaced electric or gas driven small planes and UAVs, collaborative decision-making, target localization and classification, robustness to sensor node loss, flexibility and deployment ease. The interface gives users complete control over the entire sensor network, including the ability to monitor the azimuth and elevation angles to the targets in real-time.
-
Product
Video Quality Analysis Systems
ClearView Extreme 8K and 4K Systems
-
Highest Resolution Video and Audio Quality Analyzers with 12G-SDI Interfaces and ST 2110 Networking Option
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
3U VPX Systems
-
Curtiss-Wright Defense Solutions
Our SWaP-optimized 3U VPX rugged mission computer systems are pre-integrated and pre-validated to reduce your cost, risk, and time to market. These systems are based on open standards to meet Modular Open Systems Approach (MOSA) requirements and qualified for temperature extremes, high altitudes, voltage spikes, shock, vibration, and more.
-
Product
Interference Locating System
SeeWave®
-
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
Product
Test System
LB301
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
System Controls
-
Exar Corporation offers a broad range of USB VBUS power distribution switches supporting both the USB 2.0 and latest USB 3.0 specifications. These devices, the SP/XRP252x series, are offered in single and dual channels configuration for maximum design flexibility. The XRP2527 and XRP2528 are generic single and dual channels power distribution switches capable of operating at input voltage as low as 1.8V supporting the typical 1.8V, 2.5V, 3.3V and 5V power rails. Current limit for each channel is programmable from 300mA up to 1A through an external resistor and achieves better than 8% accuracy.
-
Product
Concrete Corrosion Mapping System
15620
-
Our Concrete Corrosion Mapping System (CCMS) can be used to satisfy the ASTM C-876 standard test method and the kit contains all equipment items that are needed to perform a corrosion survey on virtually all types of reinforced concrete structures, such as bridges, highway slabs and parking garages.
-
Product
Stand-alone I-V Test Systems
-
OAI offers a complete line of high performance I -V Testers. I -V Testers and I -V Rider software may be ordered as a stand -alone system or integrated into any OAI Solar Simulator. Three standard ranges of I -V Testers are available; ≤1A, 1 -5A, 5 -10A, and 20A. Higher current testers are available as custom options. An OAI Application Engineer will work with you to insure that the I -V Tester and I -V Rider software you choose is optimized for your specific application.
-
Product
Weight Registration System
-
The number of the current hopper and the correct positioning, along with the indication of power and status, are displayed on the indicators. Four load cells are mounted on the cart. The system records the amount of material shipped from each hopper, and the total weight of the material in the trolley is also displayed. All information is stored in the controller memory for a specified time. After the necessary time intervals, the operator can rewrite the information on the USB drive for further processing.
-
Product
Emergency Systems
System
Safety and survival products which aid in on-board emergencies, aircraft evacuation, and search and rescue operations.
-
Product
Structural Health Monitoring System
SHM
-
Automated stationary structural health monitoring system (SHM) is a subsystem of buildings and structures control system which has been developed in accordance with the applicable requirements of the corresponding standards. It is used to detect a transition of the building state from operational into the state of failure, that may eventually lead to fatal accidents.
-
Product
Warpage Metrology System
TableTop Shadow Moiré (TTSM)
-
Measure warpage of substrates up to 300mm x 310 mm (a 300mm wafer or two JEDEC trays) with the entire measurement taking less than two seconds. Whether individual parts or a JEDEC tray of multiple parts, the TTSM provides an ultra-fast and highly accurate measurement at room temperature that is suited for tabletop use.
-
Product
Multi-Function Test & Measurement System
-
Optoplex’s Multifunction Test and Measurement System (TM100 Series) is designed to provide a flexible and cost effective optical test and measurement solution, particularly for manufacturing lines. The mainframe can be mounted in 19” rack or stationed on desk-top for ease of use. There are many selections of the pluggable modules, from tunable laser, optical spectrum analyzer, EDFA, power meter, ASE light source, optical tunable filter, optical performance monitor, …, etc.
-
Product
Flying Prober Test System
QTOUCH2204C
-
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
-
Product
Steering Module Test Systems
-
Steering test systems for quiet evaluation of rattle, NVH & performance issues – non-hydraulic. The MB Dynamics Steering Module Test Simulator family of technologies (SMTS) is an assembly of components and software designed to facilitate the quiet testing, development, troubleshooting, and auditing of a variety of steering gear and steering column assemblies — collectively referred to here as steering modules (including components).
