Net
Link transmissions in communication systems.
-
Product
Multi-channel Interface Module
PC104E-MA4
Interface Module
Alta Data Technologies’ PC104E-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC PCI/104-Express interface card supported by the latest software technologies. The PC104E-MA4 card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Seismic Analysis Software
-
GeoSonics announces our latest software suite. AnalysisNET is the most comprehensive and advanced software for GeoSonics 3000 Series seismograph. The software combines Seismic Analysis and Event Manager software in a single package that employs the .NET framework. AnalysisNET allows easier access to data files provides multiple report combinations and gives you the ability to manage your data.
-
Product
C Series Digitizer Module
Digitizer
The C Series Digitizer Module takes both high-speed and high-resolution time- and frequency-domain measurements. It features up to four channels that can sample at speeds up to 20 MS/s—ideal for discrete detection of signals 10 MHz and smaller for applications such as fault detection, partial discharge analysis, and acoustic measurements. The module's store-and-forward architecture allows up to 128 Mbits of measurement data to be sent back to the CompactRIO Controller and analyzed. You can use the module as part of a CompactRIO system and use the LabVIEW FPGA Module to develop an advanced trigger based on low-speed streaming for added flexibility. This digitizer includes the NI-DAQmx driver and configuration utility that simplifies configuration and measurements. NI-DAQmx supports NI programming environments and Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
NET and C #
-
The programming software C # under .NET enables the development of test programs and additional components.
-
Product
Voltage Input Device For FieldDAQ
-
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Software
DIFFRAC.SUITE
-
DIFFRAC.SUITE represents a new software platform offering a wide range of software modules for easy X-ray powder diffraction data acquisition and evaluation. Based on Microsoft's .NET technology, DIFFRAC.SUITE offers all the advantages of most modern software technology for maximum ease of use and networking.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
C Series Sound And Vibration Input Module
Sound and Vibration
The C Series Sound and Vibration Input Module incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. The modules are compatible with smart TEDS sensors.The C Series Sound and Vibration Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Analog Output Device
Analog Output Module
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
-
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
Product
Fast & Compact XML Products
-
Highly Compact Binary encoding • Very Fast Encoding/Decoding • SAX • .NET XML • Standardized
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Pocket-size pressure logger
DEFI2-DHG & DEFI2-D
-
DEFI2-DHG and DEFI2-D are miniature pressure recorders (depth meters) for long-term observations (DEFI-D and DEFI-DHG are up to 573 days and 52 days respectively and for 1 minute interval observation). These two recorders can be used attached to fishing nets, underwater instruments and moorings. Also, AAA alkaline batteries used by DEFI-DHG and DEFI-D are easily available, reducing the operating costs.
-
Product
Subminiature USB Cameras 5 Mpix Or 18 Mpix
-
*Smallest dimensions: 15 x 15 x 8 mm, 5 grams*5 Mpix,*New model with 18 Mpix*Minimal power consumption (under 1 Watt) beneficial for UAV / UAS*USB flat ribbon flex cables ideal for Embedded vision systems*GenICam/GenTL, C/C++, Python, .NET*Windows, macOS, Linux, ARM - NVIDIA Jetson TX2 and AGX Xavier*Board level available for OEM and customization
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
Portable Multimeter
-
Basic functions:DC current: 200μA/20/200mA/10A AC, voltage: 200/600V DC, voltage: 200mV/2/20/200/600VResistor: Rx200/Rx2/Rx20/Rx200K/Rx2MSpecial functions:Diode transistor testContinuity buzzer low battery displayNegative polarity displaySelf-recovery protectionSampling frequency: 3 times/sMaximum display: 1999General characteristics:Product colors: iron-gray and orangeProduct net weight: approximately 115gLCD size: 53x33mmProduct size: 133x70x30mmPower: 1x9VPacking contents:Packing cartonHandheld bag English manualTesting lead batteryStandard individual packing carton size: 153x101x34mmCarton size: 560x325x340mm
-
Product
HTTP & HTTPS Traffic Viewer & Analyzer
HTTP Debugger
-
HTTP Debugger is a proxy-less HTTP sniffer with clean UI and very easy to use. Doesn't change the browser's configuration for the proxy. Can display HTTP(s) traffic from any browser and JAVA/.NET apps.
-
Product
PXIe-8234, 2-Port Gigabit PXI Ethernet Interface Module
780244-01
Ethernet Interface
Vision Software Included, 2-Port Gigabit PXI Ethernet Interface Module—The PXIe-8234 with Vision Acquisition Software can acquire images from the fastest GigE Vision cameras. It transfers images at full Gigabit Ethernet bandwidth on both ports simultaneously, and it is optimized for extremely low CPU load. The PXIe-8234 with Vision Acquisition Software provides full GigE Vision bandwidth at every port, giving you the bandwidth you need for your most demanding vision applications. It also includes NI Vision Acquisition Software, which is driver software for acquiring, displaying, logging, and monitoring images from a multitude of camera types. With a set of easy-to-use functions and example programs, you can quickly create applications using LabVIEW, C, C++, C#, Visual Basic, and Visual Basic .NET.
-
Product
Online Audio Frequency Signal Generator
WavTones
-
We are proud to offer not only the best audio frequency signal generator on the net, but also a high-end sound generator, which compares favorably to the more expensive software and hardware tone generators!
-
Product
Software Engineering Services
-
Reston Software provides state-of-the-art, U.S.-based software development services. We can fulfill your immediate and long-term software development needs by creating new applications, supporting and enhancing existing applications, and modernizing legacy applications.We focus primarily on Microsoft technologies: .NET, WPF/XAML, Visual C++, COM/ATL, ASP.NET, Microsoft Office plug-ins.We also specialize in upgrading legacy programs to modern environments. We are experienced in upgrading Visual Basic programs (from version 2.0 and higher) to the latest version of VB.NET, and in upgrading Windows NT, 2000, and XP applications to Windows Vista, 7, and 8.
-
Product
C Series Universal Analog Input Module
Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Radio Interception & Direction Finding Systems
-
Net Radios are used by many organisations including anti-national elements, and it has always been a cause of concern for the LEAs. Stratign provides solutions for interception, demodulation and decoding of HF/VHF/UHF communications with the capability of finding the actual location of the transmitters.
-
Product
COM Express Compact Size Type 6 Module with 11th Gen Intel® Core™ and Celeron® Processors (formerly codename: Tiger Lake-UP3)
cExpress-TL
Computer on Module
ADLINK cExpress-TL,based on the 11th Gen Intel® Core™ i7/i5/i3 and Celeron™ processor, is the first COM Express module to support PCI Express Gen 4 at 16 GT/s, effectively doubling the bandwidth of previous generations. Additionally if features support for 2.5GbE Ethernet, leveraging existing Cat5e cable infrastructure being used for 1GbE Ethernet, it supports four USB 3.2 ports with transfer rates up to 10Gb/s. The modules have a configurable power range of 15 to 28 watts, which suits them for fanless space-constrained embedded applications. Typical industries in need of such high-performance/low-power characteristics are transport, medical, industrial automation and control, edge controllers, robotics and multi-camera-based AI. cExpress-TL features the Intel® Iris® Xe, a new graphics core, and supporting AVX-512 Vector Neural Net Instructions (VNNI) can significantly improve the number of elements processed per cycle, providing AI inferencing performance that is up to 3x that of previously available from non-VNNI platforms. Intel® Iris® Xe provides 96 execution units and is able to be configured to support two 8K independent displays or four 4K independent display (HDMI/DP/eDP). Additional support includes In-Band ECC (IBECC), providing ECC level error correction on DDR4 SODIMM memories for mission critical or rugged applications.
-
Product
Technological Solution
Ducknet
-
The Duck Net system is the technological solution by Ducati Energia to create an energy management and monitoring system compliant with the standards ISO50001, ISO14001, ISO50001, directive 2012/27/UE, Italian law DL 4-7-2014 n. 102
-
Product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
-
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Product
Operating Software for elowerk Test Systems
TestBuilder
-
elowerk TestBuilder is the operating software for elowerk test systems. TestBuilder is based on the Microsoft .Net Framework and runs on Windows Vista and Windows XP. Test programs can be created by CAD data import. The comfortable graphical user interface allows a straightforward editing of test programs. Customized applications can be programmed using a programming interface.
-
Product
Communication Protocol Test Harness
-
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
Product
4-Component Net-Radiometer
LPNET14
-
LPNET14 is a 4-component net-radiometer for the measurement of the net radiation between 0.3 μm and 45 μm.
-
Product
C Series Voltage Output Module
Input/Output Module
The C Series Voltage Output Module helps you update analog output models that feature overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. This module includes up to 16 channels. Some models include a channel-to-earth ground double isolation barrier for safety and noise immunity as well as improved signal quality, and some higher density models conserve chassis space, which leaves room for other measurement types.The C Series Voltage Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
