-
Product
Battery Chargers
-
The JUNXY intelligent battery charger covers three charging processes: (1)Constant current charging → (2)Constant voltage with decreasing current charging→ (3)micro current floating charging. Auto shut-down when reach any one of four charge cutt-off settings: (1)cell voltage, (2)charge duration, (3)charge capacity, (4)manual stop charge. It is especially designed for battery bank maintenance for different industries with nominal voltages: 24V, 36V, 48V, 80V, 96V, 110V/120V, 220V/240V, 380V etc with different charging current.
-
Product
MIL-C-24217 Connectors
107 Series
-
The Teledyne DGO 107 Series connectors are rugged, metal shell connectors manufactured and tested to the stringent requirements of Mil-C-24217, and used primarily in Navy dry mate submersible applications where reliability in differential pressure applications is critical.
-
Product
1.0/2.3 Connectors
-
Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.
-
Product
Battery Monitoring System
FST-TA
-
Foresight Electronics Co., Ltd.
Continuous 24/7 on-line monitoring One CELLCHECK monitor one cell, including internal resistance, voltage and temperature Software is available to collect data from CELLCHECK Serial port with Optical isolation, meet MODBUS protocol, easy to be accessed by UPS controller Easy to install without specialized training Full resistance, battery temperature and voltage monitoring for comprehensive battery state of health analysis String current and ambient temperature monitoring
-
Product
Battery Discharge Capacity Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
RF Connectors
SMB Connectors
-
The SMB interface features a snap-on coupling mechanism and is available in 50 ohm configurations. SMB connectors conform to the requirements of MIL-C-39012, and the interface is in compliance with MIL-STD-348. SMB connectors offer broadband performance with low reflection DC to 4 GHz and extended performance up to 10 GHz.
-
Product
Connector Inspectors
-
Our Connector Inspector video microscopes feature a hand-held probe which enables inspection of both patchcords and hard-to-reach in-adapter connectors.Connector images can be captured and stored on your PC with an optional USB2.0 adapter.
-
-
Product
Swagelok-Type Battery Test Cell With Three-Electrode System
TBT1
-
Liquid electrolyte battery test cell with PTFE sleeve and corrosion-resistant metal components, designed for stable laboratory testing up to 10 MPa and 200°C.
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
Battery Management (BMS) Environmental Test System
Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
Battery Voltage Relay
BVR
-
Battery Voltage Relays supply alarm indications at precise voltages for undervoltage and overvoltage conditions. The BVR is designed to prevent damage and incorrect operation during anticipation transient conditions.
-
Product
Two-Quadrant SMU For Battery Drain Analysis, 20 V
N6781A
Source Measure Unit
The Keysight N6781A is a source / measure unit (SMU) designed specifically for the task of battery drain analysis. Whether the device under test (DUT) is an eBook reader, MP3 player, mobile phone, or pacemaker, the N6781A’s seamless measurement ranging, programmable output resistance, and auxiliary DVM combine the best set of advanced features on the market for battery drain analysis. When used with the 14585A Control and Analysis software, the N6781A becomes an even more powerful battery drain analysis solution, offering additional insights into your measurements. Learn more about the 14585A Control and Analysis software.
-
-
Product
Circular Connectors
-
Complete range of circular connectors with metal and plastic shells, and crimp and solder terminations for multichannel hybrid electrical/ optical insert arrangements, supporting a wide range of allowable contact voltages and currents, easy environmental sealing and rugged mechanical performance.
-
Product
Card Edge Connectors
R600
-
VECTOR Electronics and Technology, Inc.
R656-2R600 series card edge female connectors for 0.062"(1.57mm) thick boards. Available in wire-wrap or solder tail type termination.Available in 30, 72, 44, 56, 80 and 100 contacts total with dual row.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel With V/I Readback
41-752A-013
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
2.92mm Connectors
-
Pasternack 2.92mm connector category includes many part numbers, most of which are RoHS and REACH compliant. 2.92mm connector series in this category will terminate to coax or terminal. These 2.92mm connector products are built to precise microwave and RF industry specifications. 2.92mm connectors are manufactured in male or female gender with 50 Ohm impedance. 2.92mm connectors are available in threaded, bulkhead, 2 hole panel, 4 hole panel or mountless options. These 2.92 mm connector designs include clamp/solder, field replaceable or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 2.92mm connector series is in-stock. In addition to being in stock, these 2.92mm connectors will ship the same day as they are purchased.
-
Product
Flow Battery Test Cell Mold For Laboratory Research
FBT1
-
Flow battery mold for laboratory electrochemical testing and electrolyte circulation experiments. Made with titanium alloy, PTFE, and copper, it provides corrosion resistance and stable performance for flow battery research.
-
Product
Automatic Battery Monitor
BA24-2020
-
The BA24-2020 automatic battery tester makes it easy and efficient to test each cell of a battery. It makes it possible to receive a new battery and to revalidate it regularly.
-
-
Product
Board Interconnect Connectors
-
ECT compliant Board Interconnect offers flexibility in unpredictable mating environments. They offer ultra-high service life for industrial docking stations, tool changers, board stacking mezzanine applications, or sub-assembly interconnects where tolerance stack-ups make fixed pin connections unreliable.
-
Product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
-
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
Product
Vacuum & Airtight High-Pressure Battery Test Cell
VAH1
-
PMMA vacuum airtight battery test chamber with Ø100 × 180 mm inner dimensions, supporting +0.1 MPa positive pressure and vacuum down to -0.2 MPa for battery safety testing and transport simulation.
-
Product
Battery Testing Chambers
ET-SERIES
-
These Chambers are designed and manufactured to meet various types of battery testing requirements of its customers by keeping all safety options in mind against any harmful explosions or ignitions and user safety while testing these batteries for environmental stress conditions
-
Product
68 Pin VHDCI Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Connectors
-
Panasonic Automotive & Industrial Systems Europe GmbH
: They have to be as compact as possible and provide maximum reliability. To fulfil these requirements, Panasonic engineers have developed narrow-pitch connectors that utilize TOUGH CONTACT technology.In addition to their excellent shock and vibration resistance, these connectors feature an ultra slim profile, which makes them ideally suited for applications where space is valuable. Our versatile in-device connector product range offers the appropriate solution for practically any scenario.
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
High-Precision Battery Tester
-
Arbin's High-Precision Battery Tester (HPS) is equipped with state-of-the-art technology, ensuring unmatched accuracy and precision.
-
Product
CTEK MXS 5.0 Battery Charger
40-206
-
The MXS 5.0 offers a unique eight-step approach to battery care. Fully automatic microprocessor controlled charger with built-in automatic temperature sensor features a unique combination of advanced charging modes and makes the new MXS 5.0 the fastest, most effective and versatile consumer charger CTEK has ever made. Alligator Clamps and Eyelets included.
