Transformer Test
Measure turns ratio, no-load current and winding resistance of transformers.
See Also: Transformers, Transformer Testers, Current Transformer Test, Current Transformer Test Set
-
Product
Distortion Test Set-Up
Model E
-
The Model E Distortion Tester is for testing those products that may have moderate amounts of distortion, such as pressed and formed parts of glass or plastic. It can be used for performing the distortion test required in several military specifications, such as MIL SPEC DTL-43511D.
-
Product
Voltage Transformer
-
Beijing GFUVE Electronics Co.,Ltd.
Are a parallel-connected type of instrument transformer. They are designed to present a negligible load to the supply being measured and have an accurate voltage ratio and phase relationship to enable accurate secondary connected metering.
-
Product
GSM/EDGE Analysis Using NI PXI RF Test Instruments
NI-RFmx GSM/EDGE
Test Instrument
The NI-RFmx GSM/EDGE personality is a highly optimized API for performing physical layer measurements on GSM/EDGE cellular standard signals. NI-RFmx GSM/EDGE is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
Test & Monitoring Recorders
-
Curtiss-Wright Defense Solutions
From miniature avionics bus recorders to high-speed, high-capacity units with customizable interfaces, we use our decades of experience designing and manufacturing flight test and monitoring recorders to deliver solutions that meet the newest standards.
-
Product
Climatic Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Climatic test chambers are also referred as environmental test chambers, which is the general name of various test chambers that simulate the natural climate environment of raining, high temperature, low temperature, constant temperature, illumination, dewing etc, products including constant temperature chamber, constant humidity chamber, ozone aging test chamber, UV accelerated weathering tester, vacuum hot air oven, salt spray chamber, steam aging tester, rain test chamber, dust proof test chamber, ventilation aging chamber, xenon lamp weathering test chamber and so on.
-
Product
Assembly & Test Services
-
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
Product
ETL Testing
-
Data is of utmost importance in digital systems. Protecting data, therefore, is of utmost importance. ETL refers to Extract, Transform, and Load. It supports the movement of data from its source to storage. With ETL testing we ensure that the data is not lost or corrupted during this movement. Huge volumes of data are collected in various formats and sources. The mapping process of these data is error-prone and can have quality issues.
-
Product
Information Technology Testing
-
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing information technology products according to applicable standards. We help you not only verify the classification of your product, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
Product
Environmental Test Chambers
-
Bionic Scientific Technologies
Environmental Test Chambers offer precisely controlled environment required in insect and biological research, electronics production (battery testing and PCB manufacturing) and polymer testing (plastic and rubber testing) etc. Designed ruggedly and fitted with technology advanced instruments, our environmental chambers are available from benchtop cabinets to complex large capacity walk in rooms. At Bionics Scientific, we design and manufacture environmental chambers or climatic test chambers matching with customer required specifications and supply them worldwide at factory price.
-
-
Product
Cloud Test
-
Validate your underlying network infrastructure and devices to ensure secure, reliable performance, and connectivity while meeting industry conformance and compliance standards.
-
Product
Automation Testing Services
-
Alphabin Technology Consulting
Delivering applications at lightning speed is as crucial as the high quality of the product, automating repetitive tasks with test automation services.
-
Product
EMC Test Equipment
TDEMI Mobile series
-
New dimensions for pre-certification. The TDEMI Mobile (TDEMI M) product line of GAUSS INSTRUMENTS is a very compact designed instrument especially for mobile use outside as well as in labs on the developer workbench providing a great variety of functionalities. By its standard 12V power supply it can be easily used for onboard testing, e.g. in vehicles or aircrafts. Designed for pre-certification tasks the TDEMI M provides the absolutely unrivaled advantages in speed and performance of the very well established and approved real-time signal processing and microwave technology of GAUSS INSTRUMENTS. Thus, your pre-certification investigations can be performed up to 16000 times faster than by conventional receivers. The instruments can be ordered for the frequency ranges up to 1 GHz, 3 GHz, 6GHz or 7 GHz starting from 9 kHz or optional even starting from 10 Hz. The fully gapless real-time analysis bandwidth of 225 MHz (Option RTEMI225-UG) of the spectrogram mode makes the TDEMI M series unique in the instrumentation market for pre-certification and provides a perfect tool for
-
Product
Variable Transformer DC Power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
Microbiology Testing Products
-
Bio-Rad microbiology products are a diverse array of: Culture media, rapid assays, biochemical tests, direct antigen detection, immunological serotyping, latex agglutination, and other tools for the recovery, growth, identification, and measure of microorganisms from clinical specimens.
-
Product
Sand & Dust Test
-
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
Product
Peripheral Level Transformer
-
The Peripheral Level Transformer (PLT) is an adapter module that increases the voltage of the analog inputs&outputs for easy communication with external devices. It is connected between the instrument and the periphery.
-
Product
Cyber Security Testing
-
Security testing that exposes vulnerabilities before attackers do. QAble runs structured penetration testing and security validation to uncover exploitable vulnerabilities, access control failures, and data exposure risks that automated scanners can't find.
-
Product
Stator Test Systems
-
Automation Technology's STS-3800 has become the "gold standard" in Stator Testing Equipment. The STS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems, it is backed by the industry leading two-year limited warranty. The STS-3800 offers the most comprehensive testing of stators and fields available.
-
Product
Environmental Simulation Testing
-
MET's Environmental Simulation Labs, on both coasts, employ numerous environmental chambers, including several large walk-in chambers. Hydraulic and electro-dynamic shakers are used for a wide range of vibration testing, from ISTA packaging to seismic compliance testing. MET's hydraulic vibration systems are capable of full level (Zone 4) seismic simulation.
-
Product
Flexible Test Connectors
-
Pin and socket sizes 22, 20, 16, 12 and 8 conform to MIL Spec dimensions. Whenever connector reliability is important, you’ll find NASA-approved FLEXCON test connectors. Applications include electronic, electrical and communications systems, computers, space vehicles, missiles, aircraft and other military equipment.
-
Product
Mechanical Shock Testing
-
Classical • Half-sine • Sawtooth • Shock Synthesis • Sustained Presure Shock Response Spectrum (SRS) • Transient Shock Response
-
Product
Magnet Testing
RMP Rotor Measuring Station
-
The RMP Rotor Measuring Station is a universal measuring system for the precise measurement and quality control of multi-pole permanent magnet rotors.
-
Product
Transformers & Reactors
-
Our company leads the market by manufacturing and exporting a wide range of Transformers & Reactors. We manufacture these equipments in different models and technical specifications to suit clients' demands. Our highly skilled team use best grade raw materials and components to manufacture these Transformers & Reactors. We offer these equipments to clients at competitive prices.
-
Product
Test & Measurement
-
High-quality connection solutions for precise measuring, testing and examination. Whether low or medium voltage range, whether precise test runs or preventive measuring and testing: With an extensive portfolio of specific components and cables, Stäubli always ensures perfect and reliable contact between the measuring instrument and the points, objects and systems to be tested. In addition, we are a proven partner of leading manufacturers of measuring instruments in this field, for example for equipping them with high-quality sockets. Every product meets all quality and safety standards.
-
Product
WHQL testing
-
The purpose of Microsoft's Windows Hardware Quality Labs is to certify that a device is compatible with Microsoft operating systems. Companies whose devices pass this series of tests are qualified to display the Microsoft Windows logos and can be listed on Microsoft's Hardware Compatibility List (HCL), www.microsoft.com/hcl/.
-
Product
Test Cells
-
Our test cells accurately characterize the dielectric properties of liquids and solid material.
-
Product
Testing Cars and Trucks
-
Sun Test Systems develops, produces and installs high-quality testing equipment suitable for dynamic vehicle testing at the end of the production line.As a result of the long-term and intensive cooperation with our customers products have come into being with unique features such as high safety, great flexibility, optimal operational reliability and low costs during the long life span.
-
Product
Cloud-Based Application Testing
-
QAble tests cloud-hosted applications against real infrastructure, validating functional correctness, scalability, resilience and security configuration so cloud-specific defects are caught before production exposure.
-
Product
Performance And Quality Testing
-
Underwriters Laboratories Inc.
Our endless pursuit of the truth helps you provide trustworthy answers to questions about products, processes, facilities and systems. Our testing, certification and verification services—and the UL Mark—provides regulators, purchasers and consumers with the information they rely on to confidently make the decisions that impact your business. Our quality assurance checks help to ensure that components and products meet your—and your stakeholders’—demands.
