Showing results: 16 - 30 of 33 items found.
-
CG118 -
EMC Instruments Corporation
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
TDK HRN-0118 -
TDK RF Solutions Inc.
The TDK HRN-0118 broadband horn antenna (1 GHz to 18 GHz) is designed specifically for radiated emissions and immunity measurements in EMC test environments. The HRN-0118 horn antenna provides optimal performance over the frequency range of 1 GHz to 18 GHz.
-
Seibersdorf Labor GmbH
The PLA-R and PLA-T are active, battery powered receive and transmit loop antennas for the frequency range 9 kHz - 30 MHz intended for radiated emission testing (PLA-R) and site validation: Normalized site Attenuation, Shielding Effectiveness (PLA-SET consisting of PLA-R and PLA-T)
-
TBPS01 -
TekBox Singapore Pte. Ltd.
The TBPS01 EMC near field probes H20, H10, H5 and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation.
-
SA1002 -
Laplace Instruments Ltd.
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
AR RF/Microwave Instrumentation
These rugged, dependable high gain log periodic antennas give you the constant high intensity fields you need for RFI and EMI testing in and out of a shielded room. They deliver frequency response and field intensity beyond the norm. AR’s log periodics are designed for high power radiated testing and can be calibrated for emissions.
-
Com-Power Corporation
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
EMCTEST
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
Rohde & Schwarz GmbH & Co. KG
Complete your EMC test setup with the essential accessories to compliment the test equipment. Whether it is a LISN (or V-Network) to counteract interference from external power sources on conducted emissions from the device under test, probes to locate the near field sources of radiated emissions, receive and transmit antennas, or tripods for holding antennas in place, the Rohde & Schwarz catalog of EMC accessories provides the additional items you need for EMI and EMS measurements, guaranteed 100% suitable for use with Rohde & Schwarz EMC test equipment.
-
EMCTEST
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
Series RTW -
Kepco, Inc.
Kepco's RTW series are general-purpose, L-chassis, single output power supplies.They are available in 50, 100, 150 and 300-watt power levels. Their small size and very low profile allow the RTW to be fitted into small spaces. They feature full safety compliance to international standards and have suppressed both conducted and radiated emission to FCC class B levels.
-
EMC Test Antennas -
Seibersdorf Labor GmbH
There are some changes in the calibration standard ANSI C63.4 concerning the calibration procedures of hybrid antennas, also the newly issued standard - CISPR 16-1-6 dealing with EMC antenna calibration is covered by our services. You are very welcome to consult Seibersdorf Laboratories calibration experts for the recommended calibration procedures of the most common radiated emission test standards.
-
Series RMW -
Kepco, Inc.
Kepco's RMW series are 300-watt general-purpose, U-chassis, single output power supplies, with model RMW 51212K-300 offering a triple output: +5V and ±12V.Their small size and very low profile allow the RMW to be fitted into small spaces. They feature full safety compliance to international standards and have suppressed both conducted and radiated emission to FCC class B levels.
-
Com-Power Corporation
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
-
TS8996 -
Rohde & Schwarz GmbH & Co. KG
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.