Batteries Test
-
Product
Battery Test and Analysis System
BTAS-16
-
The task of testing an aircraft’s Nickel-Cadmium batteries is complicated and involved because of the high number of cell voltage readings that need to be taken during testing. Taking voltage readings from all 20 cells in the typical nickle-cadmium aviation battery multiple times is laborious and error prone, but must be done to properly estimate the condition of the battery under test.
-
Product
Battery Testing Systems
-
The CT2001 series Battery Testing Systems are designed for energy storage materials research and battery test. The eight channels are independently programmed and controlled by the computer. The Current ranges are from 1 mA to 5 A and Voltage ranges from 2V to 15V. Each testing system is specifically built for customer needs.
-
Product
Scienlab Battery Test System — Cell Level
SL1002A
-
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
Product
Battery discharge testers
-
The battery discharge testers are used to test batteries by discharging them in a specified mode: given resistive load, fixed discharge current, etc. Depending on the required power rating, various sizes are available from manually transportable testers to multiple electronically controlled units in a master/slave configuration. Five Series of standard models.
-
Product
All-In-One Battery Testing System
-
Integrating charge-discharge and temperature testing into one.
-
Product
High Current Electronic Load (600W-1200W)
ELCH600 & ELCH1200
-
- Low lead resistance <5m Ohm for Fuel-cell- Battery Testing- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR- OV/OC/OP/OT protection- Communication: USB/RS232/GPIB
-
Product
Electrical Test Instruments
-
Transcat offers all types of electrical test instruments for diagnosis, troubleshooting, and repairing of any products and devices. Our wide array of handheld, bench, and portable equipment covers virtually every electrical testing application. Whether its battery testing, fault location, or resistance testing Transcat has all the essentials to outfit an electrician.
-
Product
Load Banks
-
From battery discharge testing to power equipment verification, our load banks are designed for precise testing and maintenance, helping you maintain peak performance and compliance with ease.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
-
Compact solution for testing Battery Packs with output power up to 110 kW and voltage range up to 1500 V
-
Product
Battery Temperature Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Battery Testing
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
Powerful AC/DC Power Supply For Testing Circuit Breakers
POB35AD
-
POB35AD is a power supply unit employing the latest power electronics technology. POB35AD generates ripple free DC-voltage and it is developed for regular maintenance tests of power circuit breakers. It eliminates use of stationary batteries during testing. Output voltage is selectable from 10 to 250V AC/300VDC. The test set is a powerful and versatile unit with possibility to generate up to 30A.
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
Life Cycle Module Testing System
LCN
-
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Insulation & Multifunction Tester (LCD Display)
1152 MF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Portable Slimline Tube Tester
741200
-
Battery powered high-frequency generator for testing pumped neon tubes and fluorescent lamps, operates on 4 AA batteries. Tube being tested will illuminate in a pulsating manner if “good”. Includes leather case. 6-7/8” long x 1-1/2” wide x 3/4” deep. Batteries not included.
-
Product
Battery Discharger & Capacity Tester
IDCE-8X0
-
Fuzhou Fuguang Electronics Co., Ltd.
Wide Range: IDCE-8X0CT series can cover 10V~480V for multiple batteries test requirements like telecom (48VDC), powerutilities (110VDC, 220VDC), UPSs (300-60 VDC), traction batteries(12-96VDC)etc.
-
Product
Insulation & Multifunction Tester (LCD Display)
1154 TMF
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Battery Analyser 12V Language
BA12L
-
The Battery Analyzer 12V Language (BA12L) is a 12V battery analyzer with English language text display easy and convenient to use by technicians and users. Has 4 main function tests: Battery, Starter, Alternator & Grounding
-
Product
48V / 300 Amp Load
BD18-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
Lithium Battery Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
Lithium battery test chambers are important in this rapid blooming era for electronic products, electric vehicles and storage systems. Lithium-ion Batteries are the widest applied in these products. The battery safety is one of the critical factors before launching such a product into market. And the demand for lithium battery test chambers is growing rapidly.
-
Product
Power Analyzer
-
E-Mobility - eDrive, and Electric Vehicle TestingAdvanced and easy to use solutions for complete electric and hybrid vehicle testing in the development, validation and production phase. One-stop solutions for electric motor and inverter testing, battery and battery charge testing, combustion analysis, hydrogen engine testing and more.
-
-
Product
Multi-Channel Battery Testing
-
The Multi-channel system includes turnkey integration of Greenlight's environmental chamber, load bank, power supply and data acquisition system, all housed in 19" rack towers.
-
Product
Wireless Battery System Tester
EECS550
-
Snap-on Tools has launched the new Snap-on EECS550 Wireless Battery System Tester that eliminates the need for a second technician. “The EECS550 maximizes manpower and gets the critical job of battery system testing done with just one set of hands,” says Dave Brekke, product manager for Snap-on. “Snap-on has listened to techs in shops where this work is a daily task. The tester will change the way techs are able to service cars, trucks, motorcycles, golf carts, ATVs and more. From the strong, built-in magnets that hold the tester in place to the easy-to-see, back-lit screen that displays in eight languages and reports battery, starting and charging system conditions, this tester takes productivity to the next level.”
-
Product
Battery Test & Automation Solutions
-
Chroma specifically developed battery cell test solution which is an integrated solution for battery cell formation & grading processes. From battery cell formation procedure to grouping process, Chroma 17900 series are customized with professional planning service which includes manufacturing flow path planning, test station/ equipment planning, test data management and so on to create high performance manufacturing capability.
-
Product
230V / 36 Amp Load
EL08-230M
-
For High Voltage UPS Battery Testing and Power Supply testing. This particular Load has been designed to operate with UPS Battery Systems and Telecom Rectifiers and Power Supplies with output Voltages in the range of 153V to 230V and is extremely cost effective.
-
Product
Analoge Sound Level Meter
Model KM-20/ YF-20
-
Kusam Electrical Industries Limited
One-handed simple, easy to operate. Inbuilt reference signal. Inbuilt battery test. Quickly, accurately sures sound level. Compressed scales minimise range switching. An internal reference signal is available for checking the meter’s operation. Calibration Check. Microphone with Capacitance Microphone.
-
Product
Electronic Loads
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
