Distributed Antenna System
-
Product
1202a High Frequency Distribution
-
Precise Time and Frequency, Inc.
The ptf 1202A High Frequency Distribution amplifier provides high performance frequency references for laboratory or system use requiring distribution at frequencies of 30MHz and above.The ptf 1202A is especially designed to distribute the high frequency input signal to 12 separate outputs, with minimum signal distortion and maximum isolation between individual output signals.
-
Product
Desktop PCB Test System
BOARDWALKER 9627
-
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
1208/9a Optical Distribution, RX/TX
-
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
Product
Antenna, Log Periodic
EM-6947 | 200 MHz – 5 GHz
-
The EM-6947 is an ultra-wide bandwidth log periodic dipole array aimed at applications requiring consistent performance over a very wide frequency range. Capable of both receiving and moderate power level transmitting, the EM-6947 can take the place of two or more conventional antennas, allowing you to take full advantage of the tuning range capabilities of modern receiver and spectrum analyzer designs with less inconvenience caused by the need to switch antennas.
-
Product
Distributed Motion Control
-
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).The modules convert input/output signals to engineering units and transmit/receive, in ASCII format, to/from any host computer with an RS-232 or RS-485 port. NuDAM modules are the key components in flexible and cost effective remote data acquisition and control systems.
-
Product
Antenna Characterization
-
Radiometrics Midwest Corporation
Radiometrics Open Area Test Site and 10 Meter Anechoic chamber provide ideal test sites for antenna characterization.
-
Product
Signal Conditioning and RF Distribution
-
CAES provides high performance signal conditioning and RF distribution solutions such as switch matrices for the EW, missile, radar, communications and space markets. Our custom designs offer high speed switching, low insertion loss, low harmonic level and excellent isolation.
-
Product
AM/FM Antennas
-
Our range of well-crafted and designed AM/FM antennas keep your onboard entertainment playing.
-
Product
Array Antennas
-
An antenna array (or array antenna) is a set of multiple connected antennas which work together as a single antenna, to transmit or receive radio waves. The individual antennas (called elements) are usually connected to a single receiver or transmitter by feedlines that feed the power to the elements in a specific phase relationship. The radio waves radiated by each individual antenna combine and superpose, adding together (interfering constructively) to enhance the power radiated in desired directions, and cancelling (interfering destructively) to reduce the power radiated in other directions. Similarly, when used for receiving, the separate radio frequency currents from the individual antennas combine in the receiver with the correct phase relationship to enhance signals received from the desired directions and cancel signals from undesired directions. More sophisticated array antennas may have multiple transmitter or receiver modules, each connected to a separate antenna element or group of elements.
-
Product
Antenna, Ultra-Wideband, Directional
EM-6945 | 500 MHz – 25 GHz
-
The EM-6945 Vector Log Periodic antenna covers the broadest frequency range available in such a small, rugged, deployable package. Offering the uncompromising performance you’ve come to expect from Electro-Metrics, a state-of-the-art design provides the antenna characteristics you need, unmatched by others in the community.
-
Product
Antenna, Log Periodic
EM-6951 | 300 MHz – 1 GHz
-
The Electro-Metrics EM-6951 Log Periodic Antenna was designed to operate over the 300 MHz to 1 GHz frequency range.
-
Product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
-
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
Product
Antenna Positioners
-
CAES is a leading designer and manufacturer of custom antenna positioners, that accurately acquire, track, and point a variety of RF payloads in military land, sea, and airborne environments.
-
Product
Radar Antenna Positioners
-
CAES is a leading designer and manufacturer of custom radar antenna positioners for military airborne, ground, and naval applications.
-
Product
Cable & Antenna Analyzer
CAA-100A
-
DTF/Frequency Return Loss, VSWR, Cable Loss, RF Power and Spectrum. CAA-100A integrates two functions: cable and antenna measurements and spectrum analysis. Cable and antenna analyzer with frequency range 1MHz – 4.4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc.
-
Product
Fluid Distribution Panels
PAO-DII
-
As a further convenience, we offer our PAO-DII Fluid Distribution Panels to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger second generation PAO-II Chiller. You can also use PAO-DII Fluid Distribution panels with any other source of temperature controlled fluid including a Bemco PCL-III Portable Chiller. These systems are individually assembled to match the product being tested.
-
Product
Analysis Tool for ECU Networks and Distributed Systems
CANape
-
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware, CANape can store multiple gigabytes of data per second. Calibration data management and convenient measurement data evaluation including data management as well as reporting make CANape a complete tool for ECU calibration. Of course, CANape also provides access to bus data, diagnostic data and analog measurement data.
-
Product
Antenna, Omni-Directional Wideband Discone
EM-6105 | 10 KHz – 2 GHz
-
The EM-6105 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6105 acts as an active vertical rod which offers 10 to 12 dB more signal handling capability than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport. The EM-6105 is supplied with an EM-6106 Battery Pack.
-
Product
System Synchronizer and Distribution Board - VME
Model 6891
-
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
Product
Sector Antennas
-
A sector antenna is a type of directional microwave antenna with a sector-shaped radiation pattern. The word "sector" is used in the geometric sense; some portion of the circumference of a circle measured in degrees of arc. 60°, 90° and 120° designs are typical, often with a few degrees 'extra' to ensure overlap and mounted in multiples when wider or full-circle coverage is required (see photos below). The largest use of these antennas is as antennas for cell phone base-station sites. They are also used for other types of mobile communications, for example in Wi-Fi networks. They are used for limited-range distances of around 4 to 5 km.
-
Product
Antennas
-
Specialist antennas for signal intelligence, radiomonitoring and super resolution direction finding.
-
Product
RF Antennas
-
These antennas are specially designed for IoT devices, are easy to implement, and provide high efficiency and performance. RF antennas are available in several configurations, with options for the number and range of frequency bands, antenna construction, and RF connector mating interfaces.
-
Product
Antenna Solutions
-
From concept to completion, Molex ready-to-use RF antennas are compact, high performing and available in multiple form factors for all standard antenna protocols and frequencies.
-
Product
Iridium Physical Layer Test Systems
PLTS
-
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
Product
12-Ch 10A RCV Power Distribution Unit
AR438
-
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
Product
Test Antennas
-
Lumistar provides small, lightweight portable fixed antennas for Test applications. They are available in lower L thru S bands for transmit and receive applications.
-
Product
2.5G Distributed Feedback Lasers
-
Macom Technology Solutions Holdings Inc.
MACOM’s Distributed Feedback (DFB) laser diodes are designed for direct modulation uncooled operation up to 2.5Gb/s. These products utilize patented Etched Facet Technology (EFT) for exceptional reliability with the following benefits: *Etched Facet Technology enabling high performance and product uniformity*Wide operating temperature range for wireless, PON and datacenter applications*No isolator required due to high back-reflection rejection
-
Product
Semiconductor Test System
TS-960e
-
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Measuring Small Antennas
-
If you have a small PCB with a small antenna you can't use a thick cable and a large connector. Not only is this impractical (how to connect the connector?) but the metal bulk will also affect the antenna and grounding properties of your PCB. The measurement will be useless. MegiQ promotes the use of the small and popular UFL connector and its associated cables. The UFL socket fits on almost any PCB and it can be improvised on a board without a UFL footprint.
-
