Showing results: 916 - 930 of 1260 items found.
-
Model JI-216 -
Jupiter Instruments
The JI-216 I2C Bus Monitor is a low cost, easy-to-use PC hosted instrument specificallydesigned for troubleshooting and debugging I2C networks. The JI-216''s FPGA basedarchitecture provides for the capture and display of all valid or invalid messages and I2Cbus events. Captured I2C messages are available for display in two modes: real-timestreaming, or triggered. These modes provide optimized data display for either hardwareor software development. The SDA/SCL timing display aids in tracking down and solvinghardware timing problems. JI-216''s broad bandwidth (DC 3.4Mbits/s), wide input signalrange (0 15.0V), and variable signal filtering provides flexibility in monitoring a variety ofI2C bus systems. An intuitive Windows application manages instrument setup andcontrol. Communications and unit power is provided via a USB 2.0 link.
-
SKU-016-XX -
Amfeltec Corp.
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
-
DFLSOBD2 -
Dafulai Electronics
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
CEB94000 -
Axiomtek Co., Ltd.
The COM Express development baseboard, the CEB94000, supports standard ATX form factor, flexible expansion with PCIe x16, PCIe x1 and 32-bit/33MHz PCI bus. Dual 7 segments port 80 display is reserved for convenient debugging purpose.
-
SKU-001-0X -
Amfeltec Corp.
The 32-bit PCI Extender was designed to support the development, debugging and verification of 32-bit PCI boards. The extender provides a complete PCI debugging platform that allows easy access to logic signals; it has over-current protection, and supports hot-swap operation.
-
Keysight Technologies
VXI bus is an established standard with many years of success. With Keysight Technologies´ large portfolio of full-featured instrument quality VXI measurement modules, you can quickly develop systems for a broad range of applications and measurement domains such as DC, Analog, RF and microwave.
-
ColorCAL MKII -
Cambridge Research Systems Ltd
Calibrated and affordable colorimeter performs better than a spectroradiometer for gamma correction. Computer-controlled, bus powered USB colorimeter with an easy to use cross-platform software interface, designed for characterising and calibrating your CRT or LCD monitor.
-
PCIe-7396 -
ADLINK Technology Inc.
The PCIe-7396 is a 96-bit parallel digital input/output (DIO) card esigned for industrial applications. The plug and play feature of PCI Express Bus architecture makes it easy for users to install the PCIe-7396 on their systems quickly.
-
PCI-7256 -
ADLINK Technology Inc.
*Supports a 32-bit 3.3 V or 5 V PCI bus*16-CH latching SPDT relay outputs*Power saving on relay actuation*Output status unchanged when power-off*On-board LED indicators for relay status
-
PCI-6308 Series -
ADLINK Technology Inc.
*Supports a 32-bit 5 V PCI bus*Isolated 8-CH 12-bit voltage output*2500 VRMS optical isolation*Jumper selectable bipolar and unipolar output ranges*4-CH isolated DI and 4-CH isolated DO*Current output version available on PCI-6308A
-
LPCI-3488A -
ADLINK Technology Inc.
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
LPCIe-3488A -
ADLINK Technology Inc.
The IEEE-488 standard, also known as GPIB, is a bus interface that connects instruments with a computer to form an ATE system. Today, GPIB is still the most popular interface between computer and instruments. ADLINK"s USB-3488A, LPCI-3488A and LPCIe-3488A controller interface cards are fully compatible with the IEEE-488.2 instrumentation control and communication standard and are capable of controlling up to 14 stand-alone instruments via IEEE-488 cables. The USB-3488A, LPCI-3488A and LPCIe-3488A are designed to meet the requirements of high performance and maximum programming portability.
-
PXT1741 -
VX Instruments GmbH
The PXT(e)1741 Trigger Module ist designed to build up a connection between trigger signals from any external trigger source (5V TTL Standard) and the PXI(e) trigger bus. Therefore the device is equipped with four SMA front connectors (T1 to T4).
-
CIC301 - MIL-STD-1553 -
Andor Design Corp.
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
MIL-STD-1553 -
Excalibur Systems, Inc.
The MIL-STD-1553 multi function interface cards are compatible with all common variations of MIL-STD-1553 and provides a wide range of features normally found only on full size testers. The card can operate simultaneously as a Bus Controller (BC) and/or multiple (up to 32) Remote Terminals (RT), or as a Triggerable Bus Monitor. The card supports error injection and detection.