Fibre
cylindrical dielectric waveguide, which transmits light through total internal refraction.
See Also: Fiber, Fiber Optic
-
product
Inspection Microscope
This compact, lightweight and ergonomic Inspection Microscope is specifically designed for inspecting ferrule and fibre end faces in the field or the laboratory. The microscope provides dual-illumination, both coaxial and oblique; to produce the highest-quality image detail and superior view of fibre end face cleanliness and core condition.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Optical Transimpedance Amplifiers
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
product
Additional Components
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
product
Network Interface Controllers for Anonymous Subscriber Messaging (FC-ASM)
Fibre Channel
Avionics Interface Technologies
FC-ASM Network Interface Controllers for Avionics applications. The AIT FC-ASM NIC solutions are Quad interface modules providing 4 independent NIC interfaces on a single module. All FC-ASM and Fibre Channel protocol operations are handled onboard, providing an efficient, high bandwidth, FC-ASM protocol offload solution for 1Gbp/s and 2Gbp/s FC-ASM.
-
product
PXI Dual 2 x 2 Fibre Optic Mux SC/PC
40-860-222
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Dual 2 Channel Fibre Optic Mux Multi Mod
40-815-122-M
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
O/E Converter
TIA-1200
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
product
PXI Single 2 Channel Fibre Optic SC/PC
40-855-212
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Avionics Network Solutions HSI1760 NIC, SAE AS5653 Compliant
Avionics Interface Technologies
AIT's HS1760 (MIL-STD-1760E) as profiled under SAE AS5653 products are built on our Fibre Channel Simulyzer™ and HS1760 IP Core technology. Our HS1760 products provide Network Controller (NC), Network Terminal (NT), and FC-AE Switch capabilities.
-
product
Fiber Optical Cabling
An optical fiber, or optical fibre in Commonwealth English, is a flexible, transparent fiber made by drawing glass or plastic to a diameter slightly thicker than that of a human hair.
-
product
PXI Single 2 x 2 Fibre Optic (M Mode) ST M50
40-860-512-M50
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Launch Fiber Box
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
product
X-Ray Detector
XRT Detector Onyx
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
product
CPCIe (PXIe) Module
ACS-FC-3U-2
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
-
product
Cable Certifiers
LANTEK III Series
New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.
-
product
Fibre-optic Hydrophones
The best instrument available to measure close to the face of the ultrasound transducer, make CW measurements or to measure the acoustic pressure and associated thermal effects of a high-intensity field.
-
product
Fibre Channel
Fibre Channel continues to evolve as the preferred communications standard for mission critical and time sensitive Storage Area Network (SAN) applications. Fibre Channel supplies over 80% of the datacenter and enterprise interconnections where lossless delivery of data is required and will be used for many years to come. Gen 6 (32GFC) products and solutions are rapidly being deployed ubiquitously across key markets today.The Fibre Channel industry is now focusing efforts on the development of Gen 7 – 64GFC utilizing PAM4 signaling – and will continue to serve those applications needing higher bandwidth and guaranteed delivery of time and content sensitive data.The SierraNet Family of Fibre Channel test platforms provides best in class traffic capture, analysis, and manipulation for testing physical link characteristics and application operations. SierraNet is designed for addressing today’s high-speed storage and communications fabrics problems and compliments other tools offering industry leading visibility and utility.
-
product
Optical signal transmission
Bus systems
Allows for the transmission of high speed CAN signals via optical fibre cables during EMC tests or when there are great potential differences (high voltage).
-
product
Draw Tower Grating
(DTG)
The Draw Tower Grating Chain consists of high strength coated FBGs which are positioned in a serial configuration. Thanks to the special production process, writing the Fibre Bragg Gratings during the drawing of the Fibre, the array can be made without any splices. Furthermore the FBGs can be mounted directly on a structure without coating removal for sensing applications. The different sensing points make use of the inherent temperature and strain sensitivity of the fiber to measure temperature or strain respectively.
-
product
PXI Single 4 Channel Fibre Optic Mux FC/APC
40-850-014
The 40-850-014 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Avionics Databus Modules
Avionics interface modules from Avionics Interface Technologies, offered through Keysight, enable connectivity between your PXI test systems solution to DUT’s with aviation industry standard buses. These modules are capable of simulation, monitoring, record and play back of bus traffic enabling test and verification of avionics equipment data communication capabilities. The available interface modules support industry standard avionics based buses such as MIL-STD 1553, ARINC 429, and ARINC 664p7, and Fibre Channel.
-
product
LX-D Shore D Rubber Durometer, Hardness Tester
LX-D
Shenzhen Chuangxin Instruments Co., Ltd.
LX-D durometer is suitable for hardness test of high degree of hardness material, such as common hard rubber, hardened resin, glass, acryl, Plexiglas, thermos plastic rubber, printing plate, fibre, acryl,etc. The product conforms to GB/T531-1999 and other related standard request.
-
product
Single 2 Channel Fibre Optic Mux Multi M
40-815-212-M
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
NVM Express
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
-
product
PXI Single 2 x 2 Fibre Optic (M Mode)SCM62.5
40-860-212-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber.
-
product
Modular Test Platform
MPA®Multi-Protocol Analyzer
The MPA® Multi-Protocol Analyzer is an advanced packet optical transport traffic generation and analysis platform specifically designed for the demands of R&D, SVT, and manufacturing testing environments. The MPA provides simultaneous independent multi-port testing from 1G to 400G for Ethernet/IP, OTN & SDH/SONET and Fibre Channel.
-
product
Strain sensors
SG-01
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
-
product
635nm Visible Light Source
VLS-40
The KD Optics VLS-40 is an easy to use, hand-held, visible source used for testing fibre optic cable installations. It is especially useful when testing fibre optic cables close to the terminal equipment. The unit is pocket sized with a long battery life, making it ideal for local fault finding and continuity checking of fibres.
