Filter Results By:
Products
Applications
Manufacturers
Printed Circuit Board
See Also: PCB, Flexible Printed Circuit
-
product
Printed Circuit Board
RISER-PCM-1
WINSYSTEMS’ RISER-PCM-1 boards are designed to provide extra space in a PC/104 stack. They are printed circuit boards (PCBs) with PC/104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Panel Mount With Fan Out For Connecting To A Printed Circuit Board
Panel Mount With Fan Out For Connecting To A Printed Circuit Board
-
product
Printed Circuit Board
RISER-PPM-1
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Printed Circuit Board Bending Test Jig
Evaluation of Bending Strength of Electronic Components and Substrates
-
product
RF Connectors
Radio Frequency Coaxial Connectors Are Designed To Connect Printed Circuit Boards (PCBs) And Cables To An External Antenna, Cameras, Sensors Or Other Devices.
-
product
PCI Express
PCI Express (PCIe) is a highly successful SerDes interface that is used in computing devices spanning a wide range of applications. Currently in its fourth generation with on-going roadmap development for a fifth generation, the PCIe interface is undergoing major technical advancements that require state-of-the-art development and validation tools. For example, Gen4 PCIe devices operate at 16 Gbps per lane and are expected to deliver very low bit error rate (BER) levels even over constrained and lossy transmission channels (e.g. printed circuit boards).
-
product
1.0/2.3 Connectors
Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.
-
product
SMC Connectors
Pasternack SMC connector category has dozens part numbers, most of which are RoHS and REACH compliant. SMC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These SMC connectors are built to precise RF and microwave industry specifications. Pasternack connectors with SMC series are built in jack or plug gender with 50 Ohm impedance. SMC connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMC connector designs include clamp/solder, crimp/solder or solder attachment methods. as with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMC connector series is in-stock. In addition to being in stock, these connectors will ship the same-day as purchased.
-
product
Dip Coating Systems
SCS Dip Coating systems, which are available in free-standing floor or tabletop models, are specifically designed for production applications that do not require large in-line systems. SCS dip coating systems can be used to apply a range of coatings, as well as photo-resists and solder masks, that are part of printed circuit board applications all with a level of precision that manufacturer's demand. Both SCS models include a host of features that make them an ideal choice for lab and production operations.
-
product
LC-4.5 Voltmeter
5203
Model LC-4.5 is the first hand-held voltmeter to include a number of special features which facilitate corrosion and cathodic protection testing on underground structures. It is designed for field testing under almost any environmental conditions. Sealed Mil Spec. switches, sealed windows, a gasketed case and a printed circuit board with baked-on moisture and fungus resistant coating on both sides make this possible.
-
product
75 Ohm SMC Connectors
75 Ohm SMC connector category from Pasternack contains dozens of part numbers, most of which are RoHS and REACH compliant. 75 Ohm SMC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These SMC connectors in 75 Ohm are built to precise RF and microwave industry specifications. Pasternack 75 Ohm SMC connectors are available in jack or plug gender with 75 Ohm impedance. SMC 75 Ohm connector parts are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMC connector designs include clamp/solder, crimp/solder or solder attachment methods. Like most of the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm connector series is in-stock. On top of being in stock, these connector in 75 Ohm SMC series will ship the same day as they are purchased.
-
product
Extender
3690-3
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212A
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
product
Substrate Inspection Apparatus
The test system of the printed circuit board (mounting board) called the flying probe tester developed ahead of the world received high evaluation at the electronics manufacturing factory around the world, securing the top share of the industry and "Takaya of the board tester" We have established a firm position that.
-
product
75 Ohm SMB Connectors
Pasternack 75 Ohm SMB connector category includes dozens of part numbers, most are RoHS and REACH compliant. 75 Ohm SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB 75 Ohm connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm SMB connector products are built in jack or plug gender with 75 Ohm impedance. SMB connectors in 75 Ohm impedance are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm SMB connector series is in-stock. Not only are these connectors with 75 Ohm SMB in stock, they will ship the same day as they are ordered.
-
product
Thermal Imaging System for Electronics Testing
ETS320
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
product
ASA200
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
product
Digital I/O Card
PCI-DIO-120
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
75 Ohm MCX Connectors
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
product
16 Channel, 12-Bit Analog Input PCI Card
PCI-AI12-16A
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120MG-CM-X8G3
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
Utility Card: Flash Programming Applications
This new feature enables the Keysight Medalist i3070 ICT to perform higher speed flash programming at the ICT station in the printed circuit board assembly manufacturing line. You can combine programming and testing into a single phase, to save time and money. This in-system programming (ISP) flash solution is tester-based and does not rely on fixtures, thus enabling greater flexibility and ease of debugging.
-
product
LED Type Wafer Alignment Sensor Controller
HD-T1
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
product
Chip Scale TVS Arrays
ProTek's patented* Flip Chip TVS Arrays are designed for small circuit board applications with limited size and space availability. To reduce installation costs, the Flip Chip can be mounted directly onto the printed circuit board; similar to chip resistors and capacitors. These devices are ideal for use in portable electronics such as Cellular Phones, Cellular Phone Accessories, Personal Digital Assistants (PDAs), Laptops and Pagers.
-
product
Automated Optical Inspection System
AOI Series
Perform visual inspections of printed circuit boards (PCB) during manufacturing in which a camera is used to scan the board in extremely fine detail to check for any defects or failures.
-
product
Actuation Methods for Functional Test Systems
Functional test typically applies full operational power to a final product or a loaded printed circuit board in order to determine if the Product/ PCB performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies within its Signature Series functional test fixtures.
-
product
Silicon Nails Feature, GTE 10.00p
K8214B
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
product
PXI-2535, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-35
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2535 is a high-density 4x136 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring field-effect transistor (FET) relays, the PXI‑2535 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
TNC Connectors
Pasternack TNC connector category has many part numbers, most of which are RoHS and REACH compliant. TNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack TNC connectors are built to precise RF and microwave industry specifications. Connectors in TNC series are manufactured in male or female gender in standard polarity or reverse polarity threads, with 50 Ohm impedance. TNC connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These TNC connector designs include clamp/solder, crimp/solder, solder or solder/solder attachment methods. We offer connectors with standard or high performance levels available with brass or stainless steel bodies. As like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this TNC connector series is in-stock. Not just in stock, but also these connectors will ship the same day as they are purchased.
