Sun Simulators
replicate the sun's light.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
MIMIC® JUNOS Simulator
-
MIMIC JUNOS Simulator fully supports Juniper JUNOS® software and SNMPv1, v2, v2c, v3. Up to 100,000 devices can be simulated in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. An extensible environment allows new MIBs and devices to be added to the simulation.
-
Product
Central Office Line Simulator
AI-7280
-
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Product
Photovoltaic Array Simulator
PV8900 Series
-
Keysight’s photovoltaic (PV) simulator includes the hardware and software to test a single maximum power point tracking (MPPT) inverter accurately. Test PV voltages up to 2000 V and 60 A with a single supply. DG9000 Series software licenses are available to test string inverter with 4-, 8-, or 12-MPPT channels. Most string inverter solutions test one MPPT channel at a time — leading to test inaccuracies. Keysight's DG9000 advanced PV inverter software can test up to 12 MPPT channels simultaneously.
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
Educational Patient Simulator
EasySim®
-
The new and improved EasySim® arrhythmia simulator fits in the palm of your hand! The ultra-portable (6.6″ x 2.4″ x .5″), ultra-lightweight (10 oz.) remote control will place you on the leading edge of medical education technology. The highly intuitive design features 48 direct-access keys in a remarkably easy to use format. No codes to memorize! No fuss to set up!
-
Product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
-
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Express Module
PCIe-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
2 PRI + 8 Port FXS PSTN Simulator Adv
CH-8FXS-MOD-2PRI-A
-
One of the most feature rich PSTN simulator on the market. Unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
8 Port BRI-S/T ISDN Simulator
BRI-8ST
-
The unit has 8 S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
-
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
Test & Simulation Interface for PCI-X
PCI-X-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
Product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
-
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
Product
MIL-STD-1553 A / B Test And Simulation 3U PXI Module
PXI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*PXI trigger on 1553 bus events*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x
-
MIL-STD-1553 Test and Simulation Module for PCI Express with 1, 2 or 4 Dual Redundant channels (APE1553-1, APE1553-2, APE1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APE1553-x module is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
Simulation
-
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs. The Synopsys suite of simulation solutions are tightly integrated, best-in-class technologies that allow designers to find bugs quickly and easily, significantly improving the quality of the most complex designs and enabling first-pass silicon success.
-
Product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
-
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Product
Solar Simulators
-
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
Product
Hot Dipping Simulator
HDPS
-
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
Product
Digital Real Time Simulation Power Amplifier
PA460Bi
-
The digital real-time simulation technology is widely used in the power system. Different digital simulation system is developed such as RTDS, OPAL-RT, NI, Tynphoon, etc.
-
Product
Analog Simulator
MPLAB® Mindi™
-
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
4 Port BRI-S/T ISDN Simulator
BRI-4ST
-
The unit has four S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
