-
Product
AC/DC Digital Clamp Tester (CE)
M-260
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Auto zero adjustment for DC current offset.*Conform to IEC safety requirements.
-
Product
Paper Testing Instruments
-
Whiteness and chromaciticity tester, whiteness meter, tensile stiffness tester, automatic horizontal tensile tester, automatic horizontal tensile tester, vertical tensile tester, pulp beating (refining) freeness tester, water absorbtion tester, Cobb tester, COBB sample cutter, coefficient of friction tester, electronic bending stiffness tester, paper and cardboard thickness meter, paper and cardboard thickness meter, ink rubber tester, standard strip cutter, softness tester, carton compression tester, paper air permeability tester, internal ply bond tester, puncture strength tester, paper tearing tester, electronic tearing tester, mullen burst tester, crush tester, Bekk smoothness tester, folding endurance tester
-
Product
Microcomputer Tensile Test Machine
CX-108
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied in all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
Product
Automatic Calibration Module
ACM4509
-
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
500KG MicrocomputerTensile Test Machine
CX-106
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
Product
Flexible Packaging Testing Service
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Flexible Packaging Testing Service mainly included OTR barrier test service,WVTR Testing Service, COF Coefficient of Friction test, lamination bond strength, material analysis, physical properties, tear strength , tensile strength, puncture, slip, blocking, scuffing, film thickness variation etc.
-
Product
Impact Tester - Impact Testing Machine
-
Impact tests are used to measure the resistance to failure of materials to a suddenly applied force. The test measures the impact energy, or the energy absorbed prior to fracture. ToronTech™ offers advanced Impact testing machines to measure that energy through drop weigh tear test and Charpy impact test. We also offer machines for the preparation of specimens for these tests.
-
Product
Rubber Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
Product
Socket Saver
4690
-
The Technobox PMC Socket-Saver permits cost effective volume testing of PMC modules when used with Technobox P/N 3390 ?PMC to PCI adapter for Test.? It may also be used to reduce wear and tear on Technobox P/N 1518/1523 (?Extender/Preprocessor?).
-
Product
Tensile Testing Machines
-
Is an intelligent tensile testing machine specializing in testing the mechanical properties of various flexible packaging materials. It is suitable for test the peel force, heat seal strength, tearing resistance, deformation, puncture resistance, open force, low speed unwinding force etc of plastic film, composite film, soft packaging materials, adhesives, rubber, paper fiber and other products.
-
Product
2-500kg Computer Servo Tensile Test Instrument
JY－106B
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Computer Servo Tensile Testing Machine is widely to test the tensile, tear, peel and bend of all kinds of
-
Product
Universal Tensile Testing Machines
-
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
Product
Digital Electronic Tensile Test Machine
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
Product
Digital Clamp Tester (CE)
M-2100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Conform to IEC safety requirements.
-
Product
Tearing Tester
TGT-01
-
Jinan Leading Instruments Co., Ltd.
TGT-01 Tearing Tester is applicable in thetearing test of films, sheets, flexible PVC, PVDC, waterproof films, wovenmaterials, polypropylene, polyester, paper, cardboard, textile and non-woven,etc.
-
Product
Drop Weight Tear Tester
DWTT
-
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
Product
High-Precision Material Testing Machine Vexus
MT5 Series
-
Sinowon Innovation Metrology Manufacture Ltd.
Vexus MT5 series of material testing machine is designed in single column with maximum testing force 5KN, it is able to make the material testing about tensile, compression, bending, shearing, bonding strength, peeling, tearing, etc, it is applied to test the material such as rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials. It is a stable and affordable material testing instruments for the incoming quality control, physical test, mechanics research, material research, etc.
-
Product
AC/DC Digital Clamp Tester (CE)
M-270
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Auto zero adjustment for DC current offset.*Conform to IEC safety requirements.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
Scott Internal Bond Impact Tester
-
The Scott Internal Bond Impact Tester is used to determine tear resistance (Elmendorf). A sample is torn with the help of the pendulum device starting from a predetermined cut. The work required for a tear of a given length is measured.
-
Product
Electronic Tensile Strength Tester Pull Force Test Chamber Applicable Industri
-
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
Product
Horizontal Dedicated Friction Peel Tear Tester
FPT-H1
-
The motorised FPT-H1-i is controlled by software run on a computer and the FPT-H1-xt uses a touchscreen console to host the software. They deliver both consistency and reliability by controlling the key test parameters of force, displacement and speed.
-
Product
Textile Tensile Testing Machine
TF002
-
TESTEX Testing Equipment Systems Ltd.
Textile Tensile Testing Machine, to determine the physical and mechanical performance of tension, tearing, compression, bursting, rapture, flexibility, shear and peel and seam slippage. Especially designed to test a wide range of yarn, fabric, leather, with a huge assortment of specimen grips and software available, it can also be used for strength test of rubber, plastic, metal, wire, paper, packaging, and other materials
-
Product
Auto Tensile Tester
ATT-01A
-
Jinan Leading Instruments Co., Ltd.
ATT-01A Auto Tensile Tester is applicable in the test of physical mechanical properties of plastic films, laminated materials, adhesives, adhesive tapes, adhesive bandage (plaster), release paper, protective film, leather, rubber and paper fiber, etc. It can perform the test items of tensile, peeling, deformation, tearing, heat seal, adhesive, open force, etc.
-
Product
Material Testing Software
MS100
-
Sinowon Innovation Metrology Manufacture Ltd.
MS100 is professional software for material testing in windows system, it is able to conduct tensile, compression, bending, shearing, bonding strength, peeling, tearing and other tests for rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials.
-
Product
1000 Amp AC Digital Clamp Meter
DL6401
-
This clamp meter offers many features in addition to basic current testing. The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
Product
Enterprise Session Border Controller
eSBC
-
Session Initiation Protocol (SIP) is the communication technology employed to set up and tear down VoIP phone calls
-
Product
1000 Amp AC/DC Digital Clamp Meter
DL6402
-
With inclusion of DC current temperature & capacitance readings, this clamp meter is the ideal all purpose instrument.The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
Product
tna intelli-weigh®
omega series
-
tna intelli-weigh® omega series of multi-head weighers brings the ultimate efficiency, simplifying your weighing process while running wet or dry applications. Our advanced hygienic design goes beyond industry standards with stainless steel construction and waterproof scales, which makes maintenance and product changeovers fast and easy. The tna intelli-weigh® omega series of weighers is eco-friendly helping reduce product waste and is made with fewer parts that need changing due to wear and tear. A modular actuator unit provides quick troubleshooting, should you ever need it. IP rated 54.
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
