Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
Product
Ground Penetrating Radar Utility Locator
PinPointR
-
The ImpulseRadar PinPointR offers a clear and dependable way to quickly and easily locate, avoid or map underground utilities with the functionality required to meet approved industry standards, whilst offering market-leading performance and data quality.The enhanced bandwidth of the PinPointR antenna provides resolution beyond that of any single-channel GPR system for the detection of near-surface utility targets and other internal reflectors of interest, as well as deeper utility targets with maximum depth penetration.Key features:- RTS-based Antenna technology- Dual-channel operation- Android-driven interface- Wireless data acquisition- Integrated GPS, with external GPS support- No survey speed limitation
-
Product
DB9 DIN-Rail Wiring Board
ADAM-3909
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with DB9 connectorCase dimensions (W x L x H): 77.5 x 45 x 51 mm (3.1" x 1.8" x 2.0")To Be Used With PCI-1714U/UL, PCL-728, PCL-740, PCL-741, PCL-743B, PCL-745B
-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
Product
4 Wire Earth Resistance & Resistivity Tester
4235 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.
-
Product
Cable Fault Locators
-
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
Underground Fault Location
-
Schweitzer Engineering Laboratories, Inc.
Underground faulted circuit indicators identify the faulted cable section without a time-consuming re-fuse and sectionalize process. Applications include subsurface or pad-mounted transformers, switchgear, sectionalizing cabinets, junction boxes, and splices.
-
Product
Wire And Cable
-
Chengdu Mengsheng Electronics Co., Ltd.
We provide a variety of wire and cable products, including insulated wires, power cords, stranded wires, solid wires, wiring harnesses and connectors. Our products are widely used in security, medical, communications, instrumentation, medical, home appliances, auto parts, military, aerospace and other industries. Our products strictly comply with the product certification standards of countries and regions such as UL in the United States, VDE in Germany, CE in the European Union, and BS in the United Kingdom.
-
Product
68-Pin SCSI Micro-D Male Discrete Wire
40-962-068-M
-
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Gauge Type T Thermocouple Wire
W-TW-26
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
- RS-232 to RS-422/RS-485 Concentrator - Wiring Hub
Model 290
-
FEATURES: Break RS-485 Limit, Expand to 496 Nodes 16 Port Capacity; Each Port Settable to RS-422 or 2 Wire RS-485; Provides Isolation Between Ports; All Ports Surge Protected; Increased System Reliability. The Model 290 RS-232 to RS-422/RS-485 Concentrator offers a unique group of features for those applications using RS-422 and/or RS-485 for communications between a multiplicity of devices.
-
Product
Hazardous Location Transmitter
X80 Series
-
The ECD Hazardous Location Transmitters – Model X80 Series provides the same capabilities and general feature set as the general purpose T80 Universal Transmitter. Various configurations are available as single or dual channel for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity. The Model X80 transmitter digitally communicates with any ECD Model S88 and/or S80 Intelligent Sensor, automatically configuring the transmitter’s menus and display screens to the measured parameter. The X80 is designed with a durable stainless steel enclosure for explosion proof/exd hazardous applications.
-
Product
Field Portable Wire Analyzer
Model 2635
-
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.
-
Product
Thumpers and Cable Fault Location
-
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
Product
PXI Pull-Thru Adapter, Wired, Excalibur EXC-4000cPCI/xx
510140129
-
PXI Pull-Thru Adapter, Wired, Excalibur EXC-4000cPCI/xx
-
Product
Marker Locator
MLD-10W/G
-
Fuji Marker locator saves you time by locating buried utilities in combination with the buried electronic marker.
-
Product
Tool, Locator, QuadraPaddle, ITA
910104140
-
Used with Crimp Tool p/n # 910101103 to crimp QuadraPaddle contacts to 22-28 AWG wire.
-
Product
Multimeter with Cable Checker Phone Test Lan Wire Test
VA43
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Lan Telephone test multimeter: VA43 is a multimeter with lan wire test. phone test .cable check.
-
Product
Wire Probe Needles Materials & Pin Diameters
-
Advanced Probing Systems, Inc.
Tungsten pins and tungsten-rhenium pins can be provided with either nickel plating or silver plating. Beryllium-copper pins are supplied with a silver plating coating.
-
Product
Voltage Tester With Wire Stripper
7122A
-
Peaceful Thriving Enterprise Co Ltd
The product can measure AC voltage 10V to 1000V and DC voltage 7V to 1000V with polarity indication. All testing results will be displayed by LCD. This product can also measure continuity and RCD. Eventually, for the convenience of wire stripping and cutting, this product has combined the function of wire stripper.
-
Product
Systems for Pipe Location
-
Here you will find an overview of SEWERIN cable location systems. Starting with locating technology such as fiber optic probes for locating non-metallic pipes, a system for acoustic locating of plastic pipes, to a multi-channel receiver for the localisation of water or gas pipes, telecommunications or power cables and other live or metallic supply lines.
-
Product
50-Pin DIN-Rail Flat Cable Wiring Board
ADAM-3950
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with 50-pin flat cable connectorCase dimensions (W x L x H): 77.5 x 146.3 x 51 mm (3.1" x 5.8" x 2.0")To Be Used With USB-4751/L, PCI-1737U, PCI-1739U, PCL-722, PCL-724, PCL-731
-
Product
Second-Generation Personal Locator Beacon
Personnel Recovery Device
-
Safran Federal Systems’ Personnel Recovery Device is the world’s first personal locator beacon built specifically for the US Army that utilizes the Second Generation Cospas-Sarsat signaling technology for the most demanding search and rescue environments. It’s a robust, ruggedized, dual mode, user-friendly beacon that has introduced many new innovations in this version of the modern beacon.
-
Product
Pre- Locator
CFL PL3+
-
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
Product
Test Lead Holder For Wires Up To 0.210In (5.33mm) Dia.
1508
-
Test Lead Holder for Wires Up to 0.210in (5.33mm) Dia.
-
Product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
-
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
-
Product
Mini Coax, Contact, ITA, two .025" Square Wire Wrap Posts
610103129
-
Mini Coax, Contact, ITA, two .025" Square Wire Wrap Posts
-
Product
Pin-Line™ Collet Socket with Wire Wrap Pins
Series 0503
-
Pin-Line Collet Sockets with Wire Wrap Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with wire wrap or solder tail pins. Consult Data Sheet No. 12013 for solder tail pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Post Wire and Die Bond Inspection Machine
IV-T3300
-
IV-T3300 is a post wire and die bond inspection machine with Dual JEDEC Tray Feeder System. It features a large inspection area of 600x500mm and a quick trays change of 5-7 seconds.
-
Product
Signal, Module, ID, CASS, 64 Position, Discrete Wiring
510114108
-
Signal, Module, ID, CASS, 64 Position, Discrete Wiring.
