RF Box
A space surrounded by an electromagnetic radiation barrier
See Also: Boxes, Decade Box, Anechoic Boxes, Black Box, Breakout Boxes, Hot Box, White Box, Shielded Box, Programmable Resistance Box
-
Product
50 Ohm SMB to SMB Cable Assembly
40-977-511-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
MS-M Style 26-Pin RF Cable Assembly, Female To Unterminated, 2m, RG178 Cable
40-979A-526-2m-FU
RF Cable Assembly
This 2m long MS-M style RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with FEP insulation and an attenuation of 102dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
Breakout Box
T1000-37
-
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
Shielded box
-
Gtemcell develops a wide range of shielded box for commercial, industrial and military applications. Customized solutions according your needs!
-
Product
Wiring Boxes
-
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
-
Product
Decade Resistance Boxes
-
A range of units to cover the requirements of development laboratories and calibration and test departments. High resistance instruments provide reliable calibration of insulation testers.
-
Product
Cable Test Box
-
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
Product
Breakout Box
T1000-62HD
-
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
Product
Manual Switch Boxes
-
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
Product
75 Ohm 1.6/5.6 to 1.6/5.6 Cable Assembly
40-977-791-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
SparkFun Decade Resistance Box
-
This is the SparkFun Decade Resistance Box, an involved PTH soldering kit that allows you to quickly and accurately dial in a specific resistance value between 0 and 999,990 Ω, in 10 Ω increments. The concept is simple, a decade box is a tool that contains resistors of many values that can be accessed via mechanical switches. All you need to do is just adjust the knobs to output any of the discrete resistances offered by the box. Once assembled, each kit will have controls that correspond to the digits in a decimal number - a control for the tens position, a control for the hundreds position, and so on.
-
Product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
-
Product
PXI Octal SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-004
RF Switch
The 40-880A-004 is an octal SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1-slot PXI module, a quad switch in a 2-slot PXI module or hex and octal switches in 3-slot PXI modules.
-
Product
Switch Box for CT Analyzer
CT SB2
-
The CT SB2 switch box is an accessory for the CT Analyzer which allows automatic testing of multi-ratio current transformers. It is connected to all taps of the current transformer and to the CT Analyzer.
-
Product
VB Build-A-Box
-
The VB Series, Build a Box provides a solution for any combinations of signal transport over fiber. With the VB-10 (10 card slots), VB- 6 (6 card slots), VB-4 (4 card slots), a unit can be created to your specification by populating the case with any configuration of VB-Cards. Each card’s I/O can be sent or received over its own disparate fiber, or all signals in the box can be multiplexed onto just one fiber. Inherently portable, each unit is ready for field applications or can be rack-mounted with optional Rack Mount kits.
-
Product
RF Adapter Module For FlexRIO
RF Adapter Module
RF Adapter Modules for FlexRIO feature frequency coverage from 200 MHz to 4.4 GHz, with up to 200 MHz instantaneous bandwidth. When paired with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, you can program the FPGA using LabVIEW to implement custom signal processing, including modulation and demodulation, channel emulation, spectral analysis, and even closed-loop control. These modules are all based on a direct conversion architecture and feature an onboard local-oscillator which can be shared with adjacent modules for synchronization. RF adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
MS-M Style 26-Pin RF Cable, Female To Male, 0.5m, RG316 Cable
40-979-526-3-0.5m-MF
RF Cable Assembly
This 0.5m long MS-M style RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz. Screwlocks are provided to secure the MS-M style connector to the associated product.
-
-
Product
RF Deluxe
ICAP/4Rx
-
ICAP/4Rx RF Deluxe is an extended version of ICAP/4Rx, including simulation capability for RF frequency design. This powerful system includes everything you need to design and verify all types of board, engineering system and IC-level design. Of course, ICAP/4Rx Power Deluxe includes Intusoft's time-tested "IsSpice4" analog and mixed-signal simulation kernel, featuring more enhancement than any SPICE kernel on the market for convergence, accuracy, speed and interactive capability.
-
Product
100GHz/200GHz DWDM Module in LGX Box
-
Flyin Optronics’ 100GHz/200 GHz dense wavelength division multiplexer (DWDM module) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
Product
RF Switch
-
Shenzhen Golight Technology Co.,Ltd
RF switch is a kind of instrument with RF signal line switching and channel expansion function. It can integrate multiple RF switching devices and combine embedded data processing platform to realize the switching of multi-channel high-speed RF signal lines.
-
Product
RF Downconverters
Downconverter
Today’s high-band signal standards are using higher frequencies and wider bandwidths than ever before for applications such as next generation 5G wireless services, satellite communications, electronic warfare, and more.
-
Product
White Box Testing
-
Does your application have legacy code and your software code messy? If the answer to the above questions is ‘Yes’, your application will fail to perform as expected. Under such cases, you need to optimize the internal structure of your application so that it performs well. To test for the errors in the internal structure opt for white-box testing.
-
Product
Launch Fiber Box
-
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
Product
Decade Boxes
L C R
-
PGP Electronics Private Limited
PGP Electronics offers wide range of decade boxes for Inductance, Capacitance and Resistance. These decade boxes offer you a greater flexibility in attaining the required component value and are designed to withstand rugged operation.
-
Product
RF modules
-
Dresden Elektronik Ingenieurtechnik GMBH
2.4 GHz OEM module with chip ceramic antenna based on the ATmega128RFA1 single-chip microcontroller from Atmel
-
Product
RF Synthesizers
HS9000 Series
-
Holzworth Instrumentation, Inc.
The Holzworth HS9000 Seriesmulti-channel platform is designed to achieve optimal channel-tochannel stability across all integrated channel synthiesizers via a conductively cooled, fan-less enclosure. Specific attention is paid to phase coherency between the independely controllable channels.
-
Product
Breakout Box and Data Logger
1U643-001
-
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
-
Product
High Power Resistance Decade Box
HPRS Series
-
The HPRS Series resistance decade boxes employ state-of-the-art precision resistors of various types for high accuracy, high stability, and low temperature and power coefficients of- resistance. High-power resistors within the unit are made available without sacrificing other electrical properties.
