Showing results: 271 - 285 of 341 items found.
-
AVLINK TECHNIC TAIWAN CO., LTD.
* Intelligent functionality. * With 162 MHz pixel frequency. * Support total 38 timings. (up to UXGA) * Support Sync Type: H/V (TTL), SOG. * Low cost. * Single interface easily use. * Portable design, working time up to 8 hours by inside Re-chargeable battery. * Auto Power-off on Battery mode. * Provide total 34 patterns, Include: Color bar, Gray, Grid, Block¡K * By 16x2 Character LCD and key buttons, easily control.
-
ASPT-5300 -
ATSI
The ASPT-5300 ATC Cabinet Switch Pack Tester (HV) will run a series of comprehensive tests on the Model 2202-HV HDSP/FU. The Model 2202-HV HDSP/FU is an important component in the ATC Cabinet Monitoring System.The Model 2202-HV HDSP/FU not only provides field output drivers, but also monitors the voltage and current for each of the field outputs.
-
PM0650 -
Applied Test Resources
The pulse channels provide voltage pulses with duration control 10us to 100ms, and measures current. The combination of capabilities provides a versatile solution on fulfilling the wide range of requirements on testing a device. The PM0650 may be floated up to ±1500V to facilitate HV isolation test of devices where outputs may be connected directly to line voltages.
-
Wuhan Sangao Electrical Test Installations Limit Co.
PD-free HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The high-light characteristic of the equipment reflects the smallness in size, lighter in weight clean ,oil-free,unnecessary static of field investigation ,longer working life without maintenance and slightness in non-partial-discharge. It is used for the insulators' voltage-resistance testing.
-
Wuhan Sangao Electrical Test Installations Limit Co.
PD-free HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The high-light characteristic of the equipment reflects the smallness in size, lighter in weight clean ,oil-free,unnecessary static of field investigation ,longer working life without maintenance and slightness in non-partial-discharge. It is used for the insulators' voltage-resistance testing .
-
YDQW -
Wuhan Sangao Electrical Test Installations Limit Co.
Gas-filled HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The high-light characteristic of the equipment reflects the smallness in size, lighter in weight clean, oil-free, unnecessary static of field investigation, longer working life without maintenance and slightness in non-partial-discharge. It is used for the insulators' voltage-resistance testing.
-
YDQ -
Wuhan Sangao Electrical Test Installations Limit Co.
PD-free HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The High-light characteristic of the equipment reflects the smallness in size, lighter in weight clean, oil-free, unnecessary static of field investigation, longer working life without maintenance and slightness in non-partial discharge. It is used for the insulators' voltage-resistance testing.
-
ACA-2000 -
Shanghai Jiuzhi Electric Co., Ltd.
This Industrial PC based control system is specifically designed for the needs of HV AC testing. The system is running a Windows based operating software package. Active and passive safety is implemented into the system as independent external emergency switches, software watchdogs, graphic symbols and status information for fast understanding. A protocol file can be used for a further calculation.
-
VI-700 -
IET Labs
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
HV200/5 -
Anfatec Instruments AG
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
SGB-C -
Wuhan Sangao Electrical Test Installations Limit Co.
high voltage divider1.it is safe and reliable.2.aluminum packing chest as cabinet3.easy to carry and use.high voltage divider, high voltage meter, resistance type high voltage meter, kilo-voltmeterThis series products are general purpose HV measuring instruments ,apply in power system, Electronic Equipment Factory to test frequency AC high voltage and DC high voltage.
-
SG-SGB -
Wuhan Sangao Electrical Test Installations Limit Co.
Specificationshigh voltage divider1.it is safe and reliable.2.aluminum packing chest as cabinet3.easy to carry and use.high voltage divider, high voltage meter, resistance type high voltage meter, kilo-voltmeterThis series products are general purpose HV measuring instruments ,apply in power system, Electronic Equipment Factory to test frequency AC high voltage and DC high voltage.
-
Series BOP-HV -
Kepco, Inc.
The Kepco Model BOP 500DM and BOP 1000DM are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. The BOP-HV can be operated in either a "voltage stabilizing" or "current stabilizing" operating mode (selectable by a front panel switch). These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
MODEL SST-HV -
Transducer Techniques, Inc
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
PK-HV-001 -
Teledyne LeCroy
Accessory kit for High Voltage Differential Probe