RF Amplifiers
take low power RF signals and output RF signals that vary in the same way as the input signal, but with a raised amplitude.
See Also: Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers, Microwave Amplifiers, Rf Power Amplifiers
-
Product
Variable Gain Amplifier
VGA
-
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
RF Coaxial Load
-
RF Lambda’s coaxial loads are used to terminate RF signal chain to provide a good 50ohm match and dissipate any excess RF energy. They are available in a variety of power levels and offer low VSWR.
-
Product
Rack Mount Type Amplifiers
-
Amplifiers for each of O-, S-, C- and L-bands– Compatible with high-speed transmission (up to 100 Gbps)– Available for all signal types and protocols– Compatible with transmitters from all manufacturers– Compatible with SNMP
-
Product
Voltage Amplifiers
-
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
Product
RF Downconverters
-
SignalCore offers traditional multi-stage and single-stage RF downconverters, and Direct IQ demodulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF downconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in spectral monitoring, signal intelligence, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
-
Product
Low Noise Amplifier
1010
-
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
Product
RF Switch Matrix
-
Compact, low-insertion-loss, non-reflective microwave switches. USB controlled and powered with optional Ethernet and audio feedback.
-
Product
RF Synthesizers
HSX SERIES
-
Holzworth Instrumentation, Inc.
The HSX Series are broadband frequency sources exhibit industry leading phase noise and spectral purity performance coupled with a highly accurate dynamic range of up to +20dBm and down to -110dBm. The 1U high form factor offers 1, 2, 3 or 4 channel models; all providing the ultimate in frequency accuracy, while the phase coherent RF outputs provide the ultimate in channel-to-channel stability.
-
Product
Isolation Amplifier
-
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
Product
Transconductance & Transimpedance Amplifiers
-
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
Product
RF ATE Tester
ADIVIC MP5800/MP5806
-
MP5800 seamlessly upgrades your existing Chroma 3380, 3650 to RF ready ATE test solution, user friendly debug tools, IOT turnkey test solution.
-
Product
RF Switch
DSM8-800-2500-2867
-
Switch Matrix, 400~2500MHz,16*16, RJ-45/RS485/RS232, SMA Female, 220V
-
Product
Fiber Amplifier - Node With Supply
FANS 811-812
-
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
Product
RF & Telecom
-
The new generation of RF PXI instruments from NI and Keysights provides speed, accuracy and flexibility similar or better than rack and stack instruments, but for a lower cost. NI LabVIEW coupled with PXI hardware provides the latest PC buses, processor’s speed and optional FPGA technology, to the most demanding R&D projects or mass production lines.
-
Product
Low Noise Amplifier
-
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
Product
High voltage amplifiers (to ±500V)
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Wideband Distributed Amplifiers
-
A wideband amplifier has a precise amplification factor over a wide frequency range.
-
Product
RF Testing
-
Silicon Turnkey Solution, Inc.
Once largely confined to military and aerospace, radio frequency (RF) today has become the underlying technology for a wide range of consumer, industrial, and medical products. Like their military-aerospace counterparts, commercial RF applications require exceptional quality but with different competitive economics.
-
Product
Wideband Power Amplifiers
-
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Operational Amplifiers
Op Amps
-
Operational amplifiers, known also as op amps, play a major role in analog signal conditioning applications. Invented by Karl Dale Swartzel Jr. in 1941, these products are largely used in today’s electronic devices.
-
Product
RF Connectors
BNC Connectors
-
BNC connector types feature a bayonet style coupling mechanism that allows for quick connect and disconnect with positive locking. Mating is achieved with just a quarter-turn of the coupling nut. With a classic, dependable design, BNC RF connectors are suited to accommodate a large variety of RG and industry-standard coaxial cables, in a variety of termination styles.
-
Product
SGMA RF Source
SGS100A
-
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
High-Frequency Amplifiers
-
Tabor’s line of High-Frequency Amplifiers allows for a better, more advanced utilization of the already available digital outputs on some of Tabor’s arbitrary waveform generators.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
Product
6-Channel VME Pulse Amplifier
V860
-
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
