-
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch
40-190B-002
-
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
42-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
RS-485/RS-422 Fault Protected
-
Renesas' fault protected RS-485/RS-422 transceivers, also known as overvoltage protected transceivers (OVP), offer robust fault tolerance and high performance.
-
Product
Cable Locator Set
DL2080
-
Complete set comprising transmitter & receiver. For tracing of cables in walls and locating interruptions and short circuits in cables.
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Ground Fault Detectors
-
STB Electrical Test Equipment, Inc
STB's convenient Ground Fault Detectors may be operated with one hand and are ideal for preventative maintenance. Ground Fault Detectors indicate ground faults and electrical leakage while equipment is in operation.
-
-
Product
Metal Locator
F-90M
-
The F-90M is the professional's choice for locating buried valve boxes and covers.The F-90M detects buried metallic objects such as meter boxes, valve boxes, and manhole covers. Ferrous metal objects can be detected more than a foot beneath the surface, and their presences are indicated by both an addible tone and meter deflection.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
42-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
McMurdo FastFind 220 GPS PLB ( Personal Locator Beacon)
-
The FastFind 220 Personal Locator Beacon (PLB) uses advanced technology packed into a simple, lightweight, palm sized unit. Using the dedicated 406 MHz frequency, FastFind 220 transmits your unique ID and precise location to the global network of search and rescue satellites. The FastFind 220’s electronics design was upgraded in 2018, offering accelerated location detection with the duel GNSS capabilities — GPS & Galileo recivers. Within minutes rescuers are alerted to your situation, and receive regular position updates. Finally, emergency services can home in on your beacon’s 121.5 MHz transmission to find you. Explore the world with peace of mind. If you find yourself in a remote area without any other form of communication, activating your FastFind 220 will summon emergency assistance.
-
Product
Emergency Locator Transmitters And Beacons
-
We offer a diverse line of Beacons in form factors that can be modified and ruggedized to meet your application, from Military to Commercial to Rotary.
-
Product
FAult Detector and OScilloscope 7 Functions in 1 Device
FADOS7F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
Usage of FADOS7F1: Determining faults of all types of electronic cards such as electronic cards of medical devices, textile and any other machines; automobile electronics; computer, monitor, TV, etc. Electronic Components Test: IC, transistor, FET, IGBT, resistor, capacitor, indicator, ect. This device is used to determine the faults at all these electronic components.
-
Product
Line Mounted Detector of PtG and PtP Faults in Line Networks
LineTroll 110EμR
-
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Precision Cable Locator Range
-
Radiodetection’s precision locators are designed for optimal locate performance for damage prevention professionals working in all industries and utilities.
-
Product
Power Quality Measurement & Digital Fault Recording
-
In view of the growing number of factors with a disturbing influence on power systems and the ever increasing sensitivity of devices and installations on the consumer side, simple monitoring criteria such as undervoltage or overcurrent are no longer adequate. Reliable registration of all the relevant processes within the electrical power system calls for constant observation of a wide variety of derived parameters, such as individual harmonic content, system unbalance and interharmonics, and the swift identification of even slight deviations from the norm.
-
Product
Ocean Signal RescueME PLB1 (Personal Locator Beacon)
RescueME PLB1
-
The RescueME PLB1 is the world's smallest 406mhz & GPS enabled PLBOperation of the rescueME PLB could not be simpler. To activate the PLB: Pull the retractable antenna out by its end tab, flip open the spring loaded cover over the activation button, hold the button for 1 second until the lights blink. Visual instructions are clearly printed on the case. When activated, the rescueME PLB1 will transmit accurate position data from its 66 channel GPS for a minimum of 24 hours while the integrated strobe light ensures maximum visibility.Ocean Signal has ensured that rescueME, like all of its other safety products, exceeds statutory requirements. RescueME PLB provides an incredible 7 year battery life, and is covered by a 7 year warranty. Even after more than 24 hours of continuous operation, and when the battery power is insufficient to transmit the satellite signal, the PLB1's homing beacon and strobe light will continue to operate. This high intensity strobe light features a molded lens to enhance the visibility of its efficient LED and it gives a powerful 1 candela light emission.Self-test of the PLB can be carried out with a simple button press with the start of test and results clearly indicated by a green flashing light. The antenna is easily extended like a normal tape measure and can be retracted using the winding mechanism on the top of the unit. This unique feature greatly facilitates user training and familiarization as it is not a one time deployable antenna similar to existing PLBs.rescueME comes with a snap-in mounting bracket and universal rubber mounting strap which can be fitted permanently or with each use. It is also supplied with a detachable flotation lanyard to accommodate all scenarios out of the box.
-
Product
Vector Network Analyzer 9KHz-3.2GHz. Includes Adv Meas Kit, Distance To Fault Opt, Cal and Utl Kits
T3VNA3200
Vector Network Analyzer
Vector Network Analyzer 9KHz-3.2GHz. Includes Adv Meas Kit, Distance To Fault Opt, Cal and Utl Kits.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Hazardous Location Syringe Pump
1000HLf
-
The Teledyne ISCO HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
Product
Detection of PtG and PtP Faults on Multi and Single Core Cables
CableTroll 2350
-
CableTroll 2350 is an indicator for detection of PtG and PtP faults on multi and single core cables. The unit uses standard type current transformers. (40:1, 60:1 or 3x500:1)
-
Product
Wires and Pipe Locator
LKZ-720
-
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
Product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
Product
Acoustic Fault Detector
AFL212-AMD
-
K&S Engineering and Scientific Ltd
This compact acoustic headset, designed and manufactured by K&S Engineering and Scientific Ltd has been developed with state-of-the-art components to not only to achieve superior performance but also to offer the user an acoustic headset that is smaller than equivalent units currently available on the market. Housed in an IP67 enclosure, the unit, which is used in conjunction with a high voltage surge generator, can easily contend with wet conditions.
-
Product
Clamp-On Open-Loop DC MicroAmmeter & Insulation Fault Detector
-
The Clamp-On Open-Loop DC MicroAmmeter & Insulation Fault Detector is a precision tool designed for detecting leakage currents in insulation systems. Featuring high sensitivity, this advanced microammeter measures direct currents as low as 1 microampere (uA) and operates within a measurement range of 10 milliampere (mA) to 10 amperes (A). Utilizing a clamp-on method with a toroidal ferro-magnetic core featuring an air gap, the device integrates AMR sensors from a differential Hall magnetometer for accurate readings. Its design is particularly suitable for large hydro generator stator windings but is also effective in various electrical applications.The device's functionality is significantly enhanced by its use of two micro-ammeters equipped with advanced signal conditioning units and a demagnetization circuit, ensuring precise data acquisition. The accompanying LabVIEW software facilitates real-time monitoring and visualization of data, allowing operators to effectively track leakage currents and identify faults within insulation systems. The dual clamp-on setup enables simultaneous measurements, providing immediate insight into potential defects without the need for cutting conductors or removing insulation, thus ensuring operator safety and system integrity.
-
Product
Ground Fault Finder
FST-JD200 DC
-
Foresight Electronics Co., Ltd.
FST-JD200 not only can provide a solution on accurately testing the faults of the indirect-grounding of the direct current system, non-metal grounding, loop grounding, simultaneous grounding of the anode and cathode, balanced grounding of the anode and cathode and multi-point grounding 1.The high-precision sampling clamp meter The device uses a high resolution (0.1mA) signal sampling direct current clamp meter that can achieve multi-point grounding and high resistance ground point positioning...
-
Product
Utility Locating with LMX GPR
LMX200™
-
Unprecedented insights and target confidence. Detect traditionally non-locatable subsurface features:Non-metallic pipes, including PVC and asbestos cementConcrete storm and sewer systemsUtilities where installed tracer wiring has failedUnderground storage tanks and drainage tilesSeptic system componentsNon-utility structures such as vaults, foundation walls and concrete pads
-
Product
12" XGA TFT LED LCD Thin-Client Terminal With Intel® Atom™ Processor For Hazardous Locations Introduction
TPC-125H
-
Industrial-grade 12" XGA TFT LCD with 50K lifetime and LED backlightIntel® Atom™ E3845 1.91 GHz quad-core processor with 4 GB DDR3L SDRAM
