ESD Simulators
create known values of electrostatic discharge.
See Also: ESD Test, ESD Test Systems, ESD Generators
-
Product
OBD2/J1708/J1587 Simulator
DFLSOBD2
-
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
Product
PXI & LXI Simulation Tools
-
Our PXI & LXI simulation tools help you to accelerate the development process by simulating the product in your test system. These tools allow you to develop and test the system software independent from your application hardware. By using the tools, you can minimize the time required with the physical system.
-
Product
PXI Switching, Simulation & Instrumentation for virtually every application that can be tested
-
We are a leading manufacturer of PXI switch, simulation and instrumentation modules, available in PXI & PXIe formats.
-
Product
Solar Simulator
-
It is the optimum light source for the evaluation of requiring high degree of parallelism close to sunlight. Irradiation area and parallelism are produced according to your request.
-
-
Product
Multi-channel GPS Signal Simulator
MP6220
-
*Up to 8 channels support positioning test*Can also be used as a single channel
-
Product
Oxygen Sensor Tester And Simulator
7650
-
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
Modular Solar Array Simulators
E4360 Series
-
The E4360 Modular Solar Array Simulators accurately simulates the I-V curve of different arrays under various environmental conditions (such as eclipse, spin, rotation, age and temperature). Its small size and high power saves valuable rack space.
-
Product
Simulation And Analysis Software
fcXplorer Analyzer
-
Avionic Interface Fiber Channel Simulation and Analysis Test Software, fcXplorer, is an easy-to-use graphical user interface for Fiber Channel Simulyzer modules. fcXplorer is designed for troubleshooting, optimization, planning and configuration of fiber channel data. The low and high level protocol analysis offers acquisition, filtering, time stamping and interpretation of Fiber Channel data traffic and generates statistics.
-
Product
MIMIC® MQTT Simulator
-
MIMIC MQTT Simulator is a scalable, customizable, programmable, predictable, dynamic simulation platform designed to enable rapid development / testing / deployment / tuning / training / demonstration of large-scale Internet of Things applications.
-
Product
ESD Device Testing
-
Barth Electronics, Inc. offers complete ESD Testing to the semiconductor industry. Nothing is outsourced – all testing is performed at our factory in Boulder City, Nevada.
-
Product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
-
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
Product
Spacecraft Power Bus Simulator
-
AMETEK Programmable Power, Inc.
*Provides enhanced measurement and data-logging of up to 40 channels.*Bus Power Monitoring Unit (BPMU) can be easily relocated to TVAC chamber to ease cabling complications*Data can be viewed either in spreadsheet or graphical format*Spacecraft (Payload) Protection Unit (SPU) provides 10 μsec reaction to out-of-tolerance conditions g
-
Product
Multi-channel Battery Simulator
FT8340
-
Shenzhen FaithTech Technology Co., Ltd.
The FT8340 series is a high precision, multi-channel, dual quadrant programmable battery simulator.The current of the simulator can be charged and discharged，and supports various fault simulations, which can not only meet the requirements of BMS testing, but also meet the ATE testing of consumer electronics products.There are at most 12 channels in a device, and each channel is electrically isolated, which is convenient for users to use in series. The built-in upper computer software is easy to operate, flexible and easy to use. It supports single channel programming operations, multi-channel editing operations, and multi process programming operations.
-
Product
ARINC 429 Test And Simulation VME Module
VME-429
-
*8, 16, 32 or 64 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Solar Simulator
Unisim Compact Solar Simulator
-
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system.As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability.The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available).The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter.Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
PXI & LXI Simulation Tools
-
Would you like to do code development with minimal hardware or see real-time switching and debug information? The LXI Simulation Tool can do that for you. This tool supports the simulation of all our PXI and LXI switching products, and most of the PXI simulation products in one highly portable package. The tool provides you with a simple and highly portable platform for application development.
-
Product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
-
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Simulation Environments Software
Modelica
-
Modelica Libraries with a large set of models are available (overview, details and download). Especially, the open source Modelica Standard Library contains about 1280 model components and 910 functions from many domains.
-
Product
Synchro/Resolver Conversion & Simulation PMC boards
-
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
Product
Measurement System for ESD Protection
SampleProtect
-
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
8-Channel VME Isolated Resistance Simulator
V420
-
The V420 is an 8-channel, isolated, programmable resistance simulator. It uses entirely solid-state simulation to eliminate transient errors associated with relay switching, and provide for monotonic resistance changes. Channels are individually programmable in four resistance ranges, from 5 ohms to 65.5K. Channels can operate from microvolts up to 35V / 50mA. Overload protection and channel error detection are included.
