Showing results: 661 - 675 of 965 items found.
-
PGY-RFFE-EX-PD -
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
Saluki Technology Inc.
Saluki LSG022 analog signal generator offers 100kHz to 22GHz frequency coverage with 10ms frequency switching speed. It can be used independently or combined with the chassis to form a test system.Saluki LSG series signal source is the cost-effective choice when you need to balance budget and performance. It provides the signals you will need for radar performance evaluation, high-performance receiver test and components parameter test etc..
-
Saluki Technology Inc.
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
Saluki Technology Inc.
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
PSAXXX-11AS-X -
ZOLIX
Model:PSAXXX-11AS-X Servo Motor ,Precision Linear Stages PSAXXX-11AS-X adopt panasonic 100W or 200W AC servo motor and high level coupler,achieve high resolution,high speed,low vibrate;material is alluminum alloy by special craft; Characteristic ◆ground ball screw ,achieve high postion accuracy ◆import guide ensure straightness and parallel inconjunction with our special craft ◆strict assemble craft and test method, ensure high performance ◆servo-motor and limited swithes design, convenient for choosing controller ◆limited switches ensure safety ◆different size and travels,make products abount ◆hand-wheel achieve hand adjustment
-
Coda Systems Ltd.
High Current Test Probes, Ultra-high Current Test Probes,Kelvin Test Probes, High Frequency Test Probes, Switching Test Probes
-
TA-3 -
Tech-Aid Products
Universal weather radar test panel with integral gyro simulator and monitor jacks. Discrete test jacks for common signals, altitude select switches and a dedicated connector for the RDS series radars. Click on picture for larger view.
-
EBIRST™ -
Pickering Interfaces Ltd.
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
IBEKO Power AB
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
Series FT -
GE Digital Energy
An industry standard for CT & VT isolationfor instrument transformer and connected device testing.Up to 10 poles; Numerous configurations availableTypically mounted on switchgear and relay panels10 pole test plug available; UL and cUL recognized.
-
Series RT -
GE Digital Energy
Up to three Series FT switches can beassembled on various size 19" wide panels. One piece clear cover standardPanels available in choice of colors and materials
-
RMO-H -
Amperis sl
The RMO-H is a portable, battery-operated micro-ohmmeter based on state-of-the-art technology, using the most advanced battery mode and switching technique available today. The high-capacity Li-Po battery allows the generation of a ripple-free DC current of up to 300 A. The test current is user-selectable and generated in an automatically regulated test ramp. During the test, the RMO-H increases the current before the measurement and decreases it afterwards. This significantly reduces magnetic transients.
-
RMO TW Series -
Amperis sl
The RMO-TW instrument can perform a simple, fast and reliable verification of a transformer on-load tap changer. This instrument allows measurements of a winding resistance at each tapping position of an on-load tap changer without discharging between tests. Problems with OLTC switching, such as interruption, can be detected with these measurements. The results are displayed on a backlit LCD screen.
-
TIG-7 -
Criterion Instruments Limited
Criterion Instruments Limited Transient Interference Generator Model TIG-7 produces a high-coltage damped oscillatory waveform to be applied to the unit under test, eg a relay. This waveform simulates the kind of transient experienced in utility and telecommunication switching stations.
-
Hilkar
For low and medium voltage switchgear including :*Circuit breakers*Contactors*Disconnect switches*Fuses*Miniature circuit breakersApplied tests for low and medium voltage switchgear :*Dielectric withstand test*Impulse withstand test*Breaking capacity test*Mechanical life testElectrical life test*Over load performance test*Short circuit breaking capacity test**Short time short circuit impulse current test*Temperature rise test*Operation performance testTests for low & medium voltage panels :*Short time short circuit impulse current test*Dielectric test*Impulse withstand voltage test*Temperature rise test
