Solid-State Relay with Power FET Switch to Protect Against Overload and Short-Circuit Currents

Part No. SR75-1 - Teledyne Defense Electronics Relays & Coax Switch

The SR75 solid-state relay utilizes a power FET switch that is protected against overload and short-circuit currents. The short-circuit protection feature not only provides protection should a short or overload occur while the relay is on, but will provide protection should the relay be switched into a short. It comes in through-hole or surface-mount 16-pin DIP packages.
MSL 6

Available options include:
SR75-1 1.5Adc, 60Vdc Load; 3.8-32Vdc Control; through-hole mount
SR75-1S 1.5Adc, 60Vdc Load; 3.8-32Vdc Control; surface mount

Product Home Contact/Sales Datasheet Company Catalog Share Add To List

DC MSSRs

Teledyne Defense Electronics Relays & Coax Switch

DC MSSRs by Teledyne Relay

Product Home Contact/Sales Company Catalog Share Add To List
Solid State Relays for Switching Heavy Loads in 6-Pin Mini-DIP Package

Series C63 - Teledyne Defense Electronics Relays & Coax Switch

Series C63 solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin mini-DIP package. These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:C63-10 1A, 60Vdc Load; 8-20mAdc Control; through-hole mountedSC63-10 1A, 60Vdc Load; 8-20mAdc Control; surface mounted

Company Website Contact/Sales Datasheet Company Catalog Share Add To List
Low Profile Solid State Relays, MIL-PRF-28750 Screened

Part No. LD24KK - Teledyne Defense Electronics Relays & Coax Switch

The Series LD24KK solid-state relays are screened utilizing MIL-PRF-28750 test methods and are packaged in low profile hermetically sealed cases. These relays are constructed with state-of-the-art solid state techniques and feature fully floating power FET output technology. This allows the load to be connected to either output terminal and provides a low ON resistance. The input and output are optically isolated to protect input logic circuits from output transients. A trip status indicator turns on when an overcurrent condition has occurred and the short-circuit protection has been activated.MSL 1Available options include:LD24KK 5A, 270Vdc Load; 4.2-16Vdc Control, Short Circuit Protection and Trip Status

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Low Profile Solid State Relays, MIL-PRF-28750 Screened

Part No. LD00KM - Teledyne Defense Electronics Relays & Coax Switch

The Series LD00KM solid-state relays are screened utilizing MIL-PRF-28750 test methods and are packaged in low profile hermetically sealed cases. These relays are constructed with state-of-the-art solid state techniques and feature fully floating power FET output technology. This allows the load to be connected to either output terminal and provides a low ON resistance. The input (control) and output are optically isolated to protect input logic circuits from output transients.MSL 1Available options include:LD00KM 10A, 270Vdc Load; 4.2-32Vdc Control

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid State Relays with Low ON Resistance

Series CD - Teledyne Defense Electronics Relays & Coax Switch

The CD series Solid-state Relay utilizes the latest technology to provide a low ON resistance. The control circuit is buffered to enable the relay to be driven directly from standard CMOS or open collector TTL logic circuits. Available options include short circuit protection and current overload protection or a status output line.MSL 1CD relays are controlled by 3.8-6VdcC = Through-hole mount SC = Surface mountAvailable options include:CD00CF 2A, 60Vdc LoadSCD00CF 2A, 60Vdc LoadCD01CF 2A, 60Vdc Load; control statusSCD01CF 2A, 60Vdc Load; control statusCD20CD 1A, 60Vdc Load; short-circuit protectionSCD20CD 1A, 60Vdc Load; short circuit protectionCD21CD 1A, 60Vdc Load; short-circuit protection & control statusSCD21CD 1A, 60Vdc Load; short circuit protection & control status

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid State Relay with Power FET Switch Protected Against Short Circuits and Overload Currents

Part No. FR75-1 - Teledyne Defense Electronics Relays & Coax Switch

The FR75-1 solid-state relay utilizes a power FET switch that is protected against short circuits and overload currents. The short-circuit protection feature provides protection when a short or overload occurs while the relay is on as well as when the relay is switched into a short. The FR75-1 is packaged in a low-profi le mini-DIP metal package.MSL 1Available options include:FR75-1 0.25Adc, 60Vdc Load; 3.8-5.5Vdc Control; through hole mounted

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid State Relay with Low ON Resistance and an Optically Isolated Output

Series HD - Teledyne Defense Electronics Relays & Coax Switch

The HD solid-state relay utilizes the latest technology to provide a low ON resistance and an optically isolated output. The control circuit is buffered to enable the relay to be driven directly from standard CMOS or open-collector TTL logic circuits. Available options include short-circuit and current overload protection. The second option is a status output line.MSL 1HD relays are controlled with 3.8-32Vdc Available options include:HD00CF 2.1Adc, 60Vdc LoadHD02CF 2.1Adc, 60Vdc Load; with switch statusHD20CF 2.1Adc, 60Vdc Load; with short circuit protectionHD22CF 2.1Adc, 60Vdc Load; short circuit protection & switch statusHD24CF 2.1Adc, 60Vdc Load; short circuit protection & trip status

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Low Profile Solid State Relays, Utilizing MIL-PRF-28750 Test Methods

Series KD and LD - Teledyne Defense Electronics Relays & Coax Switch

Your product description goes here.Series KD and LD solid-state relays utilize MIL-PRF-28750 test methods and are packaged in low-profile hermetically sealed cases. They feature fully floating power FET output technology. Options include short-circuit and current overload protection plus a status output line. Switch status returns the true status of the output switch and is optically isolated from the load.MSL 1KD & LD relays are controlled with 15mAdc/3.8Vdc (TTL), and 1mAdc/0.3Vdc (CMOS).Available options include:KD00CK 5Adc, 60Vdc Load KD02CK 5Adc, 60Vdc Load; with switch statusKD20CK 5Adc, 60Vdc Load; with short circuit protectionKD22CK 5Adc, 60Vdc Load; short circuit protection & switch statusLD00CM 10Adc (5Adc without heat sink), 60Vdc LoadLD02CM 10Adc (5Adc without heat sink), 60Vdc Load; with switch statusLD20CM 10Adc (5Adc without heat sink), 60Vdc Load; with short circuit protectionLD22CM 10Adc (5Adc without heat sink), 60Vdc Load; short circuit protection & switch status

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
MIL-PRF-28750 Solid State Relay

Part No. KD44CF - Teledyne Defense Electronics Relays & Coax Switch

The KD44CF solid-state relay utilizes MIL-PRF-28750 test methods. These relays feature fully floating power FET outputs that allow the load to be connected to either output terminal and provides a low ON resistance. A trip status indicator turns on when an overcurrent condition has occurred and the short-circuit protection has been activated.MSL 1 Available options include:KD44CF 2Adc, 60Vdc Load; 3.8-32Vdc (bias voltage), 250µA (CMOS) Control;

Product Home Contact/Sales Company Catalog Share Add To List
Dual-Output 100 VDC Plastic Relay

Part No. LPBD100 - Teledyne Defense Electronics Relays & Coax Switch

The LPBD100 is a dual-output 100 Vdc plastic relay. The relay output-switch contacts are normally closed and will conduct the load current until a voltage is applied to the relay input. With 4 volts or more at the relay input, the output-switch contacts open and the relay no longer conducts. The LPBD100 assembly contains two independent, completely isolated relays.MSL 6 Available options include:LPBD100 0.25Adc, 100Vdc Load; 4-7Vdc Control;

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Dual-Output 28VDC Plastic Relay with Internal Thermal Protection

Part No. LPD60a - Teledyne Defense Electronics Relays & Coax Switch

The LPD60a is a dual-output 28Vdc plastic relay with internal thermal protection. The relay utilizes optical isolation to provide excellent input-to-output isolation. The LPD60a offers a current limiting output to protect itself and associated load circuits from transient current overloads. During an overcurrent condition, the LPD60a clamps the current to a safe operating value.MSL 6Available options include:LPBD60a 0.25Adc, 28Vdc Load; 4-7Vdc Control;

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Dual-Output 28VDC Plastic Relays with Thermal Protection

Series LPD70 - Teledyne Defense Electronics Relays & Coax Switch

Series LPD70 dual-output 28 Vdc plastic relays offer internal thermal protection. They utilize optical isolation for excellent input-to-output isolation. The LPD70 offers a current-limiting output to protect itself and associated load circuits from transient current overloads. During an overcurrent condition, the LPD70 clamps the current to a safe operating value.MSL 6 Available options include:LPBD70 0.25Adc, 33Vdc Load; 4-7Vdc Control;

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Military-Style DC Solid-State Relay for High-Current Pulse Load Applications

Part No. M33-2N - Teledyne Defense Electronics Relays & Coax Switch

The M33-2N is a military-style DC solid-state relay designed for high-current pulse load applications. It features the latest power FET output technology to minimize ON resistance. This feature provides minimum output voltage drop and allows the M33-2N to switch high pulse currents up to 100 amps at higher temperatures than those allowable with bipolar devices. The M33-2N utilizes transformer isolation to protect against transients, and are through-hole mountedMSL 1 Available options include:M33-2 7Adc, 60Vdc Load; 4.5-5.5Vdc (bias voltage), 80µA (CMOS) Control;

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid-State Relay with Power FET Switch to Protect Against Overload and Short-Circuit Currents

Part No. SR75-2 - Teledyne Defense Electronics Relays & Coax Switch

The SR75-2 solid-state relay utilizes a power FET switch that is protected against overload and short-circuit currents. The short-circuit protection feature not only provides protection should a short or overload occur while the relay is on, but will provide protection should the relay be switched into a short. It comes in through-hole or surface-mount 16-pin DIP packages.MSL 6Available options include:SR75-2 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; through-hole mountSR75-2S 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; surface mount

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid State Relays for Switching Heavy Loads with Physically Small 6-pin DIP Package

Part No. ZD20CD - Teledyne Defense Electronics Relays & Coax Switch

Series ZD20CD solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6ZD20CD 1A, 60Vdc Load; 8-20mAdc Control; through hole mountedSZD20CD 1A, 60Vdc Load; 8-20mAdc Control; surface mounted

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid State Relays for Switching Heavy Loads with Physically Small 6-pin DIP Package

Part No. ZD20CF - Teledyne Defense Electronics Relays & Coax Switch

Series ZD20CF solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD20CF 2A, 60Vdc Load; 8-20mAdc Control; through hole mountedSZD20CF 2A, 60Vdc Load; 8-20mAdc Control; surface mounted

Product Home Contact/Sales Datasheet Company Catalog Share Add To List
Solid State Relays for Switching Heavy Loads with Physically Small 6-pin DIP Package

Part No. ZD24CC - Teledyne Defense Electronics Relays & Coax Switch

Series ZD24CC solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD24CC 0.5A, 80Vdc Load; 8-20mAdc Control; through hole mountedSZD24CC 0.5A, 80Vdc Load; 8-20mAdc Control; surface mounted

Product Home Contact/Sales Datasheet Company Catalog Share Add To List