Com-Power Corporation
Com-Power Corporation has been a supplier of instrumentation for EMI / EMC Testing (electromagnetic compatibility), telecommunication ( Part68 ) and product safety ( UL / IEC CSA) testing since 1989.
- (949) 459-9600
- (949) 635-0329
- sales@com-power.com
- 1679 Placentia Avenue
Costa Mesa, California 92627
United States of America
-
Product
Bulk Current Injection Probes
-
The Com-Power CLCI-100 and CLCI-400 are precision bulk current injection probes designed for conducted immunity testing. The CLCI-100 covers 10 kHz to 100 MHz, while the CLCI-400 extends up to 400 MHz and complies with MIL-STD-461 and RTCA DO-160. Both models feature split-core ferrites for easy cable insertion and are compatible with calibration fixtures for accurate RF injection and monitoring.
-
Product
Magnetic Field Generator
-
The Com-Power APF-5060 magnetic field generator is specifically geared towards generating magnetic fields for immunity testing. The APF-5060 with its corresponding loop antennas provide a standalone solution for magnetic field immunity testing as per IEC/EN 61000-4-8 and all the derived product standards.
-
Product
Surge Generators
-
Surge Generators by Com-Power Corporation provide you to test your electronics to lightening simulation.
-
Product
Transient Limiters
-
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
Product
Conducted Immunity Test Systems
-
Conducted Immunity System (CIS) to Test According to IEC 61000-4-6. The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
Product
Impedance Stabilization Networks
ISN
-
Com-Power ISN (Impedance Stabilization Network) are primarily used for RF telecom conducted emission testing per EN 55022, which is one of the EMC (Electromagnetic Compatibility) phenomenon tests.
-
Product
LISNs - Single Phase
-
Com-Power single-phase LISNs cover 9 kHz to 400 MHz in five series — 1x, 2x, 3x, 4x, and 5x — with current ratings from 20 A to 100 A for CISPR 16, ANSI C63.4, MIL-STD 461, DO-160, and CISPR 25 conducted emissions testing.
-
Product
Antenna Kits
-
Com-Power offers five portable antenna kits suitable for offsite EMC testing. These kits are supplied with a custom hard plastic carrying case which has individual compartments for all the included items.
-
Product
Turntables
-
Used for EMC testing motorized turntables TT-400X and TT-600X are used in commercial electromagnetic compatibility testing as low-profile, above-ground platforms for spinning the equipment being tested (EUT). The turntable can hold and rotate equipment that is on a desk or on the ground. The device is turned so that the position or angle at which the EUT gives off the most electromagnetic interference can be found. By using the switch on the remote, you can turn the turntable in either direction. The motor and the gear reduction drive that goes with it make up the rotation drive. These turntables are made from non-conductive weather proof materials. You can buy any kind of ramp you want to use to move heavy equipment onto the turntable.
-
Product
Absorbing Clamps
-
The absorbing clamps also known as ferrite clamps are used for measuring disturbance power on power input lines as well as other auxiliary I/O lines.
-
Product
CDNs - Coupling Decoupling Network
-
Coupling Decoupling Networks, commonly called CDNs for IEC-61000-4-6 conducted immunity testing, serve the purpose of Injecting common mode disturbances These CDNs also ensures these signals do not interfere (decoupling) with auxiliary equipment connected to the device under test (DUT)
-
Product
Current Monitor Probes
-
Current monitor/sensing probes measure superimposed RF currents flowing in conductors or cable harnesses. The main application is to measure conducted emissions to meet various EMC standards.
-
Product
Spectrum Analyzer
-
Spectrum Analyzer from Com-Power of have a frequency range of 9 kHz up to 3.2 GHz. With their light weight, small size, and friendly user interface, the SPA-900TG offer a bright easy to read display, powerful and reliable automatic measurements, and plenty of powerful features. Applications include broadcast monitoring/evaluation, site surveying, EMI precompliance, research and development, education, production, and maintenance.
-
Product
Feed Through Capacitor
-
Feed-through capacitors with a value of 10 μF are made so that they can be used in RFI/EMI test setups like MIL-STD-461A/462A. Now, many other standards, such as RTCA DO-160G, require them to be used. In this particular application, the capacitor offers a low RF impedance across the power supply. So, a current probe can be used to accurately measure the electromagnetic interference (EMI) currents made by the device being tested.
-
Product
Current Probe Calibration Fixtures
-
Calibration fixtures are used for calibration of Coupling Loss/Transfer Impedance of current probes and BCI probes, as well as for the calibration of test levels for conducted immunity/susceptibility tests using BCI probes.
