Ono Sokki
Ono Sokki is a measuring instrument manufacturer focused on the tasks of applying digital technology to measurement applications, and has a proud history in that field, including development of Japan's first digital counter 40 years ago, and myriad products using digital technology.
- +81-45-514-2603
- +81-45-935-3808
- overseas@onosokki.co.jp
- 12F Yokohama Connect Square
3-3-3 Minatomirai
Nishi-ku, Yokohama 220-0012
Japan
-
Product
Engine Vibration detector
VP-201/202/1210/1220
-
The VP-201/202 and VP-1210/1220 are electro-dynamic vibration detectors designed for gasoline and diesel engine measurement. By mounting them on the cylinder head or an engine etc, they detect rotation vibration at the time of combustion. It is easy to use due to a small, light weight, and magnetic mounting by means of a built-in magnet on the bottom surface. The detector and the cable are reliable with heat-resistant structure so you can use it in an engine room.
-
Product
Gasoline Engine Tachometer
SE-2500A
-
SE-2500A is a non-contact handheld tachometer designed for gasoline engine measurement. Detection, measurement, and display parts are all in one unit and batteries are built in the unit. Moving the detector (head of the SE-2500A) close to an ignition coil can measure rotation speed at the unit of 1 r/min or 0.01 r/s. Up to 20 measurement data can be stored in the internal memory that is convenient for later checking.
-
Product
High-Sensitive GPS Speedometer
LC-8310 series
-
The LC-8310 high-sensitive GPS speedometer can measure the velocity of a vehicle and the distance using GPS/GLONASS.It adopts the method to correct the speed obtained from satellite signals with IMU ((Inertial Measurement Unit) and achieves high response, stable and high accuracy measurement (velocity accuracy of ±0.2 km/h, distance accuracy of ±0.2 %).
-
Product
High-Sensitivity Tri-Axial Accelerometer with Built-In Preamplifier
NP-7310
-
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
Product
F/V Converter
FV-1100
-
The FV-1100 receives signal from a rotation detector or a similar device and outputs DC current or voltage signal proportional to its frequency. As the fluctuation of the input frequency signal is continuously converted to DC voltage, it is useful for measurement and recording of transient phenomena such as fluctuation of rotating speed, current velocity, frequency.
-
Product
Linear Gauge Sensors
GS Series
-
All the GS series Digital Linear Gauges are upgraded. The GS-1700/1800 series is a compact and cost effective basic type. The GS-6700/6800 series is a vibration resistant type which provides better performance of vibration resistance 1.5 times in strength compared to the basic type. The GS-4700/4800 pursuits heavy-duty performance required in production site. Long stroke type the GS-5050/5100 series has wide measurement range (stroke) at 50 mm or 100 mm. Using ball bearing mechanisms in these all models greatly increases bearing life.
-
Product
Advanced Handheld Tachometer
FT-7200
-
The FT-7200 Advanced Tachometer is an easy-to-use handheld digital tachometer offering high functions and performance. The use of FFT (Fast Fourier Transform) technology enables the FT-7200 to perform frequency analysis of rotation speed by using change of signal in sound, vibration or magnetic flux from rotating machines such as a motor or the like. Selection from 5 kinds of measurement modes allows it to calculate and display rotation speed of any complex waveform signals from a sound level meter or an accelerometer accurately by extracting the exact frequency component.
-
Product
Vibration Comparator
VC-2200/3200
-
The VC-2200/3200 is a Vibration comparator which is used for maintenance and constant monitoring of production facilities with high accuracy, high function, and low cost in a single unit.
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
Product
External Sensor Input Type Handheld Digital Tachometer
HT-6200
-
HT-6200 is a handheld tachometer with a built-in batteries designed for measurement of gasoline/diesel engines, EV/HEV motors, and general rotating objects. Combined with optional detectors (VP-202/1220, IP-292/296, IP-3000A, IP-3100, OM-1200/1500, MP series and TTL signal output detector etc.), various rotation measurement are possible depending on the measurement objects or purpose.
-
Product
Ignition Pulse Detector
IP-3000A
-
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Product
Real-time 1/1, 1/3 Octave Analysis Software
DS-0323
-
This software analyzes the 1/1 and 1/3 octave bands for 2 - 32 channels (2 - 64 channels when two units are connected ) in real-time from 0.5 to 20 kHz. The filter is compatible with the IEC, JIS, and ANSI standards. The equivalent continuous A-weighted sound pressure level (Laeq) and the single-shot sound exposure level (Lae) are calculated simultaneously by setting measurement time. Variations in level (time series) for each band can be saved for up to 2,000 points.
-
Product
Engine Performance/Endurance Test System
-
Various types of test system as follows can be built up in combination with measurement control equipment and peripheral instruments (fuel flow meters, actuators, temperature control device, combustion analysis system, ECU monitor, OBD, sound and vibration measurement instruments, emission analyzer, smoke meter etc.)·Traveling fuel economy test·Gas emission test·Output performance test·Deterioration/endurance test·Combustion analysis·Sound source probing
-
Product
Gasoline Engine Tachometer
SE-1620
-
The SE-1620 is an engine tachometer that performs measurement of the number of revolutions of a gasoline engine by connecting an engine revolution sensor such as an ignition pulse detector. A 100-mm wide-angle meter is used for the display, and both analog output and pulse output functions are provided as standard.Simply attach an ignition pulse detector or one of our other compatible detectors to the engine to enable measurement of the number of revolutions of a gasoline engine. The inputs, outputs and input power supply are all isolated to ensure the output of analog and pulse signals with superior noise resistance and stability characteristics.
