Showing results: 46 - 60 of 91 items found.
-
PP319FTC -
Matco Tools
Full functioning voltmeter measures in 1/10th of a volt increments from 1/10th of 1V up to 70V. Easy to read dual polarity indicators: red (+) symbol indicates positive green (-) symbol indicates negative. Circuit breaker protects the vehicles electrical system and your Power Probe. 20' extension lead gives you 40' total of lead. Great for RV'S, trucks and trailers.
-
FIT550 -
Matco Tools
*Performs running, residual, rail and flow rate pressure tests*Large, easy-to-read 3-1/2" dual-scale gauge reads 0-100psi and 0-700 kPa*Kit includes: 50+ adapters, fittings, 48" hose, pressure relief and fuel discharge hose to test most domestic and foreign fuel injection systems*Also includes quick release couplers and adapters to fit other fuel injection test kits*For use with gas engines only
-
MBT100 -
Matco Tools
Tests 12V starting/charging systems, including flooded lead acid, AGM, and gel cell batteries. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries.
-
MDCOPT -
Matco Tools
The Coil-on-Plug Spark Tester provides an easy way to check ignition systems with coil-on plugs (COP). Quickest way to test for no-start conditions. Inductive test cannot be performed because there are no plug wires. Applications include Ford, Chrysler, Mitsubishi, Nissan and many more.
-
FIT13APB -
Matco Tools
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifoldIncludes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446)
-
TPT69700A -
Matco Tools
*Helps locate air leaks in turbo system components by plugging the output side of the turbo and the intake inlet*Air is applied through one adapter to show the presence of leaks within the system*Six pairs of stepped adapters to fit most turbo systems on cars and light trucks
-
FPT5000 -
Matco Tools
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
MD257 -
Matco Tools
*Provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests*Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
VG100K -
Matco Tools
*Accurately tests vacuum and low pressure fuel systems*Heavy-duty 3-1/2" dual purpose gauge reads vacuum and pressure*Quickly diagnose internal engine problems such as bad rings, valves or leaky head gaskets
-
FIT448 -
Matco Tools
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
SMOKE30 -
Matco Tools
*Creates an air-tight seal with any vehicles EVAP system, eliminating the need for searching for the EVAP service port*Capless fuel system adapter works with your smoke machine to test EasyFuel™
-
MD79 -
Matco Tools
*Provides readings for volts, amps and ohms required for automotive electrical system tests*Handy 35mm AmpTip clamp jaws ergonomically measure at jaw tip for small sized conductors up to 60A and regular current, and Hz measures at jaw center for regular conductors up to 600A*Records max, min and calculates average readings over time
-
MCVK -
Matco Tools
*Tests compression on all domestic and import cars and trucks with gasoline engines*Compression tester kit includes: 2-1/2" gauge with dual inch/metric readings: 0-300 psi and 0 to 21 kg/cm2, 14mm/18mm solid short adapter, 14mm/18mm long flexible adapter and 14mm long reach adapter*Checks vacuum and fuel pump pressure and locates air leaks in fuel lines, vacuum operated chokes and emission control systems on all domestic and import cars and trucks with gasoline engines
-
FIT13A -
Matco Tools
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifold. Includes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446); Japanese fuel injection systems; a The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
MD76500M -
Matco Tools
*Non-intrusive, quick check tool instantly verifies active or inactive coil operation*Detects the magnetic field created by a coil energizing*Tool can be used to test coil on plug, coil near plug and coil pack systems