NI

product

PXIe-6356, 8 AI (16-Bit, 1.25 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module

781053-01

NI

781053-01 - NI

PXIe, 8 AI (16-Bit, 1.25 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6356 is a simultaneous-sampling, multifunction data acquisition device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6356 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.

product

TRC-8542, CAN HS/FD Transceiver Cable

783699-03

NI

783699-03 - NI

The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is … an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.

product

sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module

787325-01

NI

787325-01 - NI

Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.

product

IVN-8561, Automotive Ethernet Interface Device

786169-01

NI

786169-01 - NI

2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.

product

Optimize Throughput And Cost For MmWave 5G Device Functional Test

NI

NI

Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:

product

Smart Camera

NI

NI

Smart Cameras combine powerful onboard processors and imaging sensors into an all-in-one vision system. Smart Camera digital I/O includes optoisolated digital inputs, optoisolated digital outputs, a RS232 serial port, and Gigabit Ethernet ports. Smart Cameras also can include built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure Smart Cameras with the included Vision Builder for Automated Inspection (AI) software and program the camera with the LabVIEW Real-Time Module and the Vision Development Module.

product

NI-9146, 4-Slot, Spartan-6 LX45 FPGA, Ethernet CompactRIO Chassis

782445-01

NI

782445-01 - NI

4-Slot, Spartan-6 LX45 FPGA, Ethernet CompactRIO Chassis - The NI-9146 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using scan-mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. The NI-9146 enables you to add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.

product

USRP-2900, 70 MHz to 6 GHz USRP Software Defined Radio Device

784039-01

NI

784039-01 - NI

70 MHz to 6 GHz USRP Software Defined Radio Device - The USRP‑2900 is a tunable RF transceiver with full-duplex operation. It offers bus-powered connectivity with USB 3.0 or USB 2.0. You also can use the NI USRP‑2900 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed device (ISM) bands; sensor networks; amateur radio; or GPS.

product

PXI Optical Switch

NI

NI

The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.

product

PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer

781774-01

NI

781774-01 - NI

Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.

product

GPIB-RS232, Instrument Control Device - Swiss 220VAC

779732-02

NI

779732-02 - NI

The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.

product

CC5002X, 2 MHz, 500 A Current Oscilloscope Probe

786848-01

NI

786848-01 - NI

The CC5002X, or Hioki 3275, is a clamp-on current probe that offers a wide DC to 2 MHz bandwidth and 500 A of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.

product

SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock

781420-11

NI

781420-11 - NI

8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.

product

NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module

781962-01

NI

781962-01 - NI

1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.

product

NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors

782385-11

NI

782385-11 - NI

The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.