PCB Piezotronics, Inc.

Product

Damped MEMS High-G Shock Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Damped MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion, as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.

Product

Cable Test Box

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.

Product

Accelerometers

356A02

-

PCB Piezotronics, Inc.

356A02 - PCB Piezotronics, Inc.

Sensitivity (10 %)10 mV/g1.02 mV/(m/s) Measurement Range:500 g pk4900 m/s pk Frequency Range: (5 %)1 to 5000 Hz1 to 5000 Hz Frequency Range: (10 %)0.5 to 6000 Hz0.5 to 6000 Hz Resonant Frequency:25 kHz 25 kHz Broadband Resolution (1)0.0005 grms 0.005 m/s rms Non-Linearity: (400 g, 3920 m/s)1 % 1 % Non-Linearity (500 g, 4900 m/s)2 % 2 % Transverse Sensitivity:5 % 5 %.

Product

Pressure Sensors For Blast Testing

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.

Product

Torque Transducers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.

Product

Low Noise Coaxial Cables For Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Low noise coaxial cables are used with single axis and triaxial charge mode sensors. This table provides relevant specifications for four cable types. Type 003 is the most commonly used, but three other types are also available.

Product

PROBE MICROPHONE ICP

377B26

-

PCB Piezotronics, Inc.

377B26 - PCB Piezotronics, Inc.

Open Circuit Sensitivity (at 250 Hz)Frequency Range (+2.2/-4.9 dB)2 to 20000 HzLower Limiting Frequency (-3 dB)Inherent Noise<45 dB(A) re 20 Pa Dynamic Range(3% Distortion Limit)EnvironmentalTemperature Range (Operating)-40 to +158 F-40 to +70 C[5]

Product

High Temperature

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® offers specially designed and tested ICP® and charge mode accelerometers for testing in extremely high temperatures.

Product

Microphone Preamplifier

426B03

-

PCB Piezotronics, Inc.

426B03 - PCB Piezotronics, Inc.

Performance: Nominal Microphone Diameter:1/4"Frequency Response: (0.1 dB) (re 1 kHz)5 to 126000 Hz5 to 126000 Hz Frequency Response

Product

Pedal Force Load Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.

Product

Endevco Miniature Piezoresistive Silicon Pressure Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Accurate and Reliable Performance at Extreme Pressures.

Product

Specialty Test And Measurement Microphones

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

When acoustic measurements need to be made in demanding environments and applications, a variety of PCB® specialty microphones are available.

Product

Ballistic Pressure Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB® has supplied high frequency, durable, quartz ballistics pressure sensors in both charge and ICP® voltage mode versions for over forty years. Keeping with our tradition, PCB continues to offer a complete line of sensors for conformal and case mouth ballistic measurements. All PCB sensors are provided with NIST traceable calibration. For pre-calibration stabilization purposes, all ballistic pressure sensors are hydraulically cycled at high pressures and most are test fired in the PCB ballistic firing range.

Product

Rod End Load Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Our rod-end load cells are designed for integration into tension measurement. They are versatile, durable, and fit easily into small spaces such as inline with vehicle tie rods.

Product

Acoustics

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

When it comes to selecting a microphone for product tests—whether for sound power, sound quality, or noise source location—there's no need to compromise to sacrifice quality or performance for affordability.