Showing results: 1 - 15 of 20 items found.
-
SY-Flow-Beta -
Synectic Electronics
This range of Flow Beta Cold Water Flow Meters is available in 6 pipe diameter sizes/ flow rate ranges. These inferential multi-jet type meters have a direct reading register and are suitable for drinking water (75/33/EEC)/WRc/WRAS MID Approved R80 T50.
-
SY042 -
Synectic Electronics
Our SY042 4-20mA Current Loop Limiter has been designed to limit the maximum current in either a 0-20mA or 4-20mA loop. Powered by the current loop, therefore installation couldn’t be simpler.
-
SY057 -
Synectic Electronics
SY057 Encoder Signal Splitter provides a convenient way of splitting a master encoder signal across multiple drives or motion controllers.
-
SY024 -
Synectic Electronics
The SY024 Frequency Scaler/Multiplier can be linked to most frequency generating devices. It can be set to multiply or divide the frequency by a simple set up. When a frequency output device like a flow meter gives insufficient pulses to give the accuracy you need, or too many pulses for your Programmable logic controller or frequency counter to handle, or if you have more than one frequency output device and the rates are different you can match them by multiplying or dividing and re-transmitting to match the outputs to one another or the capabilities of your PLC etc.
-
SY014 -
Synectic Electronics
Synectic’s SY014 Miniture Incell Bridge Amplifier is specifically designed to fit inside either transducers or strain gauged components.
-
SY-JUNCTION-IP67 -
Synectic Electronics
The SY-JUNCTION-IP67 load cell junction box is useful to parallel connection of load cells and take just one cable out to almost any indicator, either batch controller or a PLC.
-
SY028TRIP/AMP -
Synectic Electronics
The SY028 Load Cell Trip amplifier has a built in alarm functionality. Accepts millivolt inputs and switches each of two setpoint relay outputs for high and low level trips.
-
SY27 -
Synectic Electronics
The SY27 range of meter pulse splitters, often called meter pulse duplicator are designed to split and isolate pulses from *between 1 and 4 meter signals. Each input will be split into 2 solid state relay outputs eg;4 in 8 out. It works with inputs from reed switch signals, with automatic de-bounce, as well as with high frequency pulses.
-
SY027 -
Synectic Electronics
Our SY027 Pulse Splitter is designed to convert pulses from meters or other turbine devices and transmit the same pulse via two relay outputs to enable two separate instruments to measure the rate simultaneously. It can be used with either electricity, water or gas meters (NOT ATEX). The SY027 PSO has been designed for applications where a pulse is required to be isolated, re-powered and repeated on two separate outputs. It works with inputs from reed switch signals, Opto coupler, open collector, NAMUR or TTL pulse (up to 25V) with automatic debounce, as well as with high frequency pulses. The speed of pulses can be accommodated from either a very slow to super-fast. Isolated relay outputs can be created by the PSR version when an NPN pulse output from a meter needs to be converted to a single relay isolated output or two.
-
SY037 -
Synectic Electronics
The SY037 passive pulse splitter is ideal for converting pulses from meters or other turbine devices and transmitting the same pulse to three outputs to enable three separate instruments to measure the rate simultaneously. It needs no power supply. It functions simply from the pulses of the meter driving it. It is convenient for meters and any pulse generating device with reed switches, open collector or current source.
-
SY020 -
Synectic Electronics
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
Synectic Electronics
The SY018 DIN rail Voltage to 4-20mA signal converter is used to communicate analogue signals over long distances where electrical interference may be a problem. This solution is often used in the process control industry to collect the analogue values from a wide array of remote sensors. The converter is valuable because current signals are much less susceptible to noise than voltage signals. A voltage signal can be converted to current and broadcast over a long distance. 4-20 mA transmitters are common in the industry and used with high-quality sensors. The resulting signals can be use in controlling drives or to trigger instruments that have settable thresholds and limits.
-
Synectic Electronics
SY024 PR* is a Pulse Rate-Analog converter designed to accept a frequency and produce a proportional Current or Voltage output. The current output can be 0-20mA or 4-20mA and the voltage output version is user adjustable from 0-5V to 0-10V.
-
SD037 -
Synectic Electronics
Synectics’s SD037 dynamically monitors mains frequency. The filter enables high speed, high accuracy, frequency monitoring even with high levels of harmonic noise. The SD037 is highly prized in demand side energy management and the associated battery storage technologies. The unit monitors the frequency of a mains voltage signal and reports the value, on demand, via an RS232, RS485 using either simple ASCII commands or Modbus protocol.
-
SY038 -
Synectic Electronics
The SY038 is a strain gauge bridge amplifier ideal for use in load cell amplification. This Load Cell Amplifier has a variable gain functionality using a miniature dip switch which enables the user to select one of 16 ranges for transducer outputs as low as 0.25mV/V and up to 4.4mV/V, higher if specified. It has the best stability in its class and high immunity to interference. Non-interactive Zero and Span trimmers are screw driver adjustable giving a further +/-20% adjustment.