LAN Cable Testers
|Sponsor Your Catalog|
EasyCheck 900 - LAN Tester / Cable Tester and Kit Compact, Powerful and Easy to use. This high performance LAN Tester / Cable Tester is the perfect tool to enable you to install, test and verify a network faster than before.
TCT-101 - LAN Cable Tester With the multi network cable tester you can test BNC and RJ45 cabling.
SCT Series - Structured Cable (LAN) Tester Certifies Category 7, 6a, 6 and 5e cabling. • Exceeds Level IV Accuracy • 1 to 1000 MHz frequency range • Most intuitive and easy to operate LAN certification tester on the market • Powerful diagnostics pinpoint the distance to link disturbances on each measured pair.
TM-903 - LAN Cable Tester Test solution for the LAN, Video and Voice cables. - Detects opens, shorts, miswires and split pairs on the twisted pair cabling. - Measures length. - Auto backlit. - Auto power off.
TCT-200 - RJ45/BNC SOHO LAN Cable Tester Test device used BNC and RJ45 (UTP / STP) wring. Check continuity and configuration of wring with unshield and shielded modular plugs. Tests for open circuits, shorts, reversals and split pars. SHILED detected tests a cable's shield integrity. DEBUG quickly identifies which cable pairs have a specific wiring fault.
21-6568-00 - LAN Cable Tester The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus.
LK-CT003 - Multi-Modular Cable Tester LAN/USB For RJ45,RJ12,RJ11&USB with a leather bag
1.RJ45 transmitting outlet(TX)
2.USB transmitting outlet A(TX)
3.USB transmitting outlet(RX)
4.RJ45 receiving outlet (RX)
5.USB receiving outlet A(RX)
8.OFF/TEST/AUTO power switch
9.Stepwise testing button
10.Auto-testing Mode indicator
13.RJ45 receiving outlet(RX) on remote terminal
14.USB receiving outlet(RX)on remote terminal
15.LED indicator on remote terminal
TCT-009- - LAN Quicker 009 RJ45/RJ11 Mini Cable Tester Easy read correct pin configuration of 10 base T, 10 base 2, RJ45/RJ11 modular cables, 258A, TIA568A/568B, Token ring, etc.
Check for cable continuity, misfiring, open, short, grounding and pin configuration.
Remote terminator test the cable before or after the cable installation up to 1000ft. away.
One button operation ideal for professional and do-it-yourselfer.
PA-01T - LAN Cable Tester w/ Tone Generator The LAN Cable Tester with Tone Generator is a perfect companion for any network professional. The tester can enhance one’s ability to quickly locate and verify the status of commonly used voice and data cables. It can perform loop-back or remote tests of network cables, displaying the results on an LED display, which moves from pin to pin automatically or manually. Its applications include testing cable and shield integrity and tracing cable.
RWC1000K - 10MB, 100MB, Gigabit Tester for UTP Cables and LAN Devices Real World Certifier. This is the tester that changed everything. Stores 250 test results in flash for later printing! Real World Certifier. 10MB, 100MB, Gigabit tester for UTP Cables and LAN devices. Speed tests, cable propagation delay, cable skew, cable typing (Cat 3, 5, 5E, 6), attenuation, cable verification, high accuracy TDR, LAN device tester (advertised and negotiated), Tone Generator/Probe. Also has basic testing for coax cables. Available individually (RWC1000K) or packaged with the Power Panel Cat5/6 DVM in the "Cable&Power Kit"(CPK1000).
MT-7053 - Instant Lan Cable Tester 1. Instantly indicates cable type and tests for faults. 2. Button-free operation, just plug cable in and read results. 3. Checks datacom/network, voice/telecom, crossover and shielded cables.
21-8569-00 - LAN Cable Tester Open / Short / Misswiring test ?BNC / RJ45 each pin connected display ?No wire or termination ?Isolation Resistances 50K ohms test
PHCT65 - LAN/Ethernet/Telephone Cable Tracker & Tester Trace Telephone Wire and LAN Cable Trace Wires In Electrical System Verify LAN Cable Condition Continuity Test DC Voltage Probe Bright White LED Flashlight Sold as : Unit
LANTESTPRO - Professional LAN Cable Tester w. 4 Remote Loopback Plugs The StarTech.com Advanced RJ45 LAN Cable tester allows a single person to test several long cables faster and more efficiently than ever before. The tester uses remote loop-back plugs that each have their own unique ID number that the tester can identify.
21-6566-00 - LAN Cable Tester The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
mTDR-020 - LAN Cable Tester The LAN Cable Tester (Model No.:mTDR-020) is the ideal instrument for both LAN and cable network management. It combines the best of the LAN Cable Tester (Model No.:mTDR-020)'s cable measurement technologies with additional features that enable technicians to troubleshoot during LAN installation and maintenance
PK-168 NEXTpro S2 - LAN Cable Tester PK-168 is capable of wire mapping by pin & pair up to 300 meters,
Provides Telecom, Datacom and cable installers and technicians with NEXTpro S2 includes both pin by pin continuity test and split pairs (wrong twisted pairs) detection for testing Lan cable via one-ended (no remote) testing finds split pairs, opens or shorts.
RapidTrace 700 - LAN Tester / Wiremap Tester & Cable Fault Locator Compact, Powerful and Easy to use. This high performance low cost LAN Tester / Wiremap Tester and Cable Fault Locator is the perfect tool to enable you to test and certify structured cabling continuity to TIA568A/B, USOC and ISDN standards.
TCT-141 - LAN Cable tester Easily read correct pin configuration of 10baseT, 10 base2, RJ45/RJ11 modular cables.
MT-7058 - Mini Lan Cable Tester Complies with CE safety standard
Automatically detect good connections, opens, crossed wires & split pairs
Test RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cable
Pin to pin cable map indicator
Non-contact voltage detection for user safety
Traces wires with tone & remote lights allows one person operation
Compact size and lightweight design for easy to carry around
Circuit Protection for both units to ensure the testing quality
Low power consumption with auto power off function to preserve battery
Long cable test more than 300 meters
901 - TDR LAN Cable Tester Accurate to 2" (5 cm) throughout the entire range up to 2,000 ft (600 m). Digital Display shows 5 common wiring faults : Open Pair, Shorted Pair, Crossed Pair, Split Pair, and Reversed Pair. Includes 1 remote identifier for wiremapping. Extra-large backlit (ICON type 7 segment) LCD. Automatic output impedance control, auto-range, auto-zero, and auto-sensitivity allows for closely matching to a wide range of cables under test. Only V.O.P(Velocity of propagation) settings required.
QUICKLAN 6055 - Wire map tester for cable of LAN networks QUICKLAN 6055 permits to perform quickly wire mapping test of LAN networks RJ45 twisted pair cables in compliance to EIA/TIA 568A/B. The meter check all eventual wrong connections (crossed, split, inverted couples, etc..), can detect problems of the cable itself (open circuits, short circuits) and shows results in a large custom display in very simple way. By using up to 8 numbered remote control units
9185B - Lan Cable Tester/ Network cable Tester Lan Cable Tester/ Network cable Tester
• The 9185B Lan cable tester is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.
• By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit.
• The 9185B provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
• Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.
• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.
• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.
• Auto and manual scan function.
• Ground wire test.
• Lock status function.
• Buzzer sound warning for wire status.
• Display: LED indication for wire status.
• Meets EN61326-1
• Plug one end of the testing cable into the Rj45 jack of sourcing end on the master unit and another end of the testing cable into the RJ-45 jack of receiving end on the master unit.
• Press the "" button, the master unit will start a sequential scanning process if the master unit is in "auto-scanning" mode.
• Press the "" button, the pin1 LED lamps of the LED indicators will be alight if the master unit is in "manual scanning" mode.
• Note: When the battery power is low, the testing results may not be correct. Please replace with a new battery.
• You can choose a auto-scanning mode or a manual scanning mode by pressing the "AUTO" button or the "MANU" button.
• The Lock function is available in "auto-scanning" mode.
• When the loop is "OPEN", you will hear the sound of the buzzer.
• Plug one end of the testing cable into the Rj45 jack of sourcing end on the master unit and another end of the testing cable into the RJ-45 jack of the remote receiving unit, then make tests.
• Read the testing results from the LED indicator on the remote receiving unit.
258807 - LAN Identification Cable Tester An essential tool for verifying and troubleshooting local area networks. Simply push the "Test" button and see Is the cable or jack connected to a hub or network card? Does the hub or network card work in full or half duplex? Is the default link speed (10 or 100 mbps.) of the hub or network card?
Results 1 - 24 of 83