Transducers

The 6060 is a two-channel signal conditioning amplifier-digitizer module with 50 kHz or 100 kHz bandwidth and both digitized and analog outputs. The bridge input is ten-wire shielded with programmable constant voltage or constant current excitation and programmable completion for quarter, half and full bridge transducers. Automatic bridge bala ...more

Two channels of high-performance signal conditioning amplifiers for quarter, half and full bridge transducers. May also be used for RTDs, potentiometers, dynamic strain, voltage and voltage mode (ICP type) charge transducers. Each channel has programmable voltage or current excitation, autobalance, voltage and shunt calibration, differential i ...more

The 6035 input module has eight channels of programmable transducer signal conditioning amplifiers and digitizer. Each channel has programmable voltage excitation, bridge completion and balance, programmable gain instrumentation amplifier, four-pole low pass filter and sample and hold amplifier. Channel outputs are multiplexed and digitized to ...more

The 6037 has eight channels of strain gage or transducer signal conditioning amplifiers and digitizer. Each channel has programmable voltage excitation, programmable bridge completion and automatic balance, programmable gain instrumentation amplifier, four-pole low-pass filter and sample and hold amplifier. The amplified channel outputs are mu ...more

High-speed data acquisition throughput a wide variety of I/O interface modules permits computer interaction with virtually any type of sensor, transducer, or final control element. . A wide variety of I/O interface modules. Large I/O capacity. An IEEE standard (583), non-proprietary, open-architecture modular high-performance - high speed data ...more

Measurement Specialties produces a broad range of amplified output pressure transducers for everything from high volume OEM use to high accuracy applications. Measurement Specialties is recognized as the world leader in glass-bonded silicon strain gage technology. Measurement Specialties Sensors proprietary Microfused" technology emp ...more

PCB module humidity/temperature transducers from Measurement Specialties provide frequency (digital) output and are calibrated for accuracy in the range of 3-5% for relative humidity from 10-95%. Applications include automotive, HVAC and medical. Features include small size, instantaneous de-saturation, fast response time, high resistance to c ...more

MCU A/D and D/A Experiment Board. Most MCU experiment systems in the market do not have the function of A/D and D/A conversions. In order to satisfy many inquiries of this function, we add serial A/D and D/A conversion components to this model of MCU. ...more

The V385 is a VME/VXI compatible eight-channel strain-gage signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the Model V380's single excitation supply. Key to the V385's increased precision is a separate remotel ...more

Meter stores range and calibration data for six pressure transducers. Accepts interchangeable transducers with ranges of 30, 75, 150, 300, 700, and 1500psi. 0.25%FS basic accuracy. Displays 8 types of pressure units. Push button transducer selection. Built-in RS-232 PC interface. Data Hold, Auto power off, Min/Max and Zero function for offset ...more

This current transducer can be mounted on almost any digital multimeter. An induction coil transforms the current (0.1 to 300A AC) into a small voltage (1mVAC per 0.1A AC) on the output pins. ...more

The Model 500G features total user flexibility for strain-gage input, range, and display. It is compatible with both bonded-foil type (2mV/V, 3mV/V, 4mV/V) transducers and higher output, semiconductor (10mV/V, 20mV/V, 30mV/V) type strain-gages. Combining this input flexibility with user scaling, 4-digit display, small size, and low cost makes ...more

DC Amplifier PCB for Strain gage transducers. Protection class IP65. Operating voltage range 18...30V. additional interfaces. electrically isolated in-and outputs ...more

The M100 series current transducers are designed to measure AC current in single and 3 phase systems. They convert the AC signal to a DC output that is directly proportional to the input signal. The M100-AA1-AA3 are self powered (i.e. no auxiliary required) average sensing RMS calibrated voltage transducers, mA and voltage outputs are availabl ...more

Wear-resistant inductive measurement system. Straight-through plunger channel protected against damages due to overstroke. Summation and substraction by parallel or antiparallel circuit  ...more

T-ID is tailor-made transducer ID for experimental stress analysis. Even with thousands of measurement channels, each transducer has its own integrated, internationally unique number (ID) and can therefore be assigned to its measurement channel quickly and with certainty.  ...more

For experimental stress analysis, HBM has introduced a new series of strain gages (S.G.) with pigtails, based on the series that has proved its worth in stress analysis, the Y-series. A wide variety of variants of the various geometries will soon be available in different temperature sensitivity adaptations. These are provided with 40 mm-long ...more

The LP-IP and LP-IL current transducers convert an ac current input into an output signal which is proportional to the rectified arithmetic mean of the input. Accurate measurement assumes a sinusoidal input waveform. Power for the units is derived from an external source. ...more

The T5 torque flange is designed for occasional, simple torque measurement tasks in the laboratory, teaching and testing sector. ...more

Inductive displacement transducers are being used with ever greater frequency in the industrial sector, due in part to their outstanding mechanical durability and insensitivity to dirty conditions, combined with their ability to resist high temperatures and their low cost.  ...more

HP30C2 model is a transducer clamp for AC current measures with 200-2000A/1V ranges in order to perform current measurements on electrical installations. The wide dimensions of clamp permits to clamping cable up to 70mm diameter or 100x46mm bars. HP30C2 transducer can be used in connection with instruments like for example network analyzer or h ...more

HT97U model is a transducer clamp for AC current measures with 10-100-1000A/1V ranges with high resolution on electrical installations. The model is able to clamping cable with maximum diameter of 54mm or 35x35 mm and 50x12 mm bars. The HT97U transducer must be used in connection with instruments which accept a minimum input signal of 1 mV AC, ...more

Model 4215 is an intelligent microprocessor based instrument designed for measurement and control of strain gage transducer based systems. ...more

No sealing between pressure connection and strain-gauge sensor; no filling liquid. Strain-gage sensor 2mV/V. Various optional pressure connections. Excellent price/performance ratio ...more

NANO UTM universal testing systems incorporate state-of-the-art technology to achieve accurate, reproducible results for the measurement of nanomechanical properties. NANO UTM systems couple a robust design to extend instrument life with our powerful Windows-based TestWorks 4 software that both simplifies testing and enables a wide variety of ...more