Signal Processing

The PMP1000 is a parallel processing DSP board that features industry leading processing power and data throughput capabilities. The processing power is provided by multiples of Texas Instruments highest performance C6414 DSPs and the high data throughput is facilitated by the internal mechanization of the PMP1000, which utilizes multiple ...more

1. Speech channel analysis indicators: Point electric level, frequency response, electric level response, channel cross talk, idle channel noise test, quantization distortion. 2. 2M transmission system BER test. 1. Multiple test mode:A-A,A-D,D-D,D-A 2. Multiple test method: Manual test, automatic loop test, automatic end-to-end test, adaptive a ...more

Arbitrary Waveform Generator with Onboard Signal Processing ...more

8x Range vs. Imports. All U.S. Radar and Laser Band Coverage. Multi-Sensor Laser Protection. Complete VG-2 Immunity. Digital "POP" Radar Alert. Advanced AutoScan Processing. Digital Signal Processing (DSP) Virtually Eliminates False Alerts ...more

Record DC signals or slow-moving signals over very long periods. The measurements are automatically stored on your hard disk for further processing. USB connected ...more

VCDconverter is an easy to use, low cost software solution for bridging the gap from design to test. VCDconverter reads signals, timing and data from simulation test files, performs optional processing of this information and writes test program files accordingly. ...more

Modern battleground environments impose challenging requirements on the performance of radar signal processors. Signal Labs' breakthrough technology, the Simultaneous Range-Doppler Receiver, sets a new standard for detection and tracking performance of a wide range of radar systems including track-while-scan and phased array radars. ...more

The next generation ADRE Sxp is a completely redesigned data acquisition system combining GE's hardware capability with the new Sxp software platform. The new system consists of the 408 Dynamic Signal Processing instrument (DSPi) and ADRE Sxp software. Highly portable, ADRE Sxp is designed to meet the changing needs of various fleet asset mana ...more

Ballard's new OmniBus family of products takes avionics databus interfaces to the highest level of flexibility and power in the industry. OmniBus supports high channel counts of single or multiple protocols and is available in several platforms. Features include one to four DSPs for protocol processing, a PowerPC user processor, IRIG circuits ...more

Uses modern DSP (digital processing signal) technology to clearly recognize the leak sound, even when there is other noise in the environment. DSA (dual segment analysis) technology: simultaneous display of the current and minimum values ...more

JYW6300 can measure voltage, current power and applied power frequency. Adopting voltage and current synchronized AC sampling and digital signal processing technology,. Can record the applied voltage or current , and calculate the short-circuit impedance for each phase after finishing three phase testing.. ...more

Venable continues to expand the 3200 series with the 35 MHz Frequency Response Analyzer. Venable's Model 3235 continues our new concept in test instrumentation. The Model 3235 combines the latest analog and digital technology with advanced digital signal processing to provide versatile test and analysis functions. This instrument operates with ...more

ArtemiS, the versatile analysis software from HEAD acoustics, is the ideal solution for all areas of signal processing, sound and vibration measurement and analysis. Investigation of acoustic and mechanical system properties, general sound and vibration analysis, sound quality, product development and optimization, quality control, material te ...more

The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The ...more

The HM5510 has a measurement range 150 kHz to 1.05 GHz. It has a hybrid design with digital frequency generation, analogue signal processing and analogue signal display by cathode ray tube. ...more

The VDTR1, Video Detector and Switch, will detect the loss of video on the A input and automatically switch to the B input. The video detector is based on digital signal processing of the A input sync signal. If the A input has excessive noise, missing or intermittent for over 100mS the switch will occur. Momentary losses for less than 100mS are ig ...more

The BOSA-C is the only high resolution Optical Spectrum Analyzer which measures optical spectra with a top combination of high resolution (0.08 pm) and high dynamic range (>80 dB) at one time, for any span and fast measurements. This provides very detailed spectra, never seen on the existing optical spectrum analyzers, which contains relevant infor ...more

Network Analyzers R3765 and R3767 measure amplitude, phase and group delay. Thanks to high-speed signal processing, the analyzers can perform measurements at a high rate of 0.15 ms per test-point. Models have a TFT colour LCD allowing simultaneous display of up to four diagrams and eight traces. A programmable sweep function is provided in all ...more

Delphi Engineering Group's ADC3100 is a PMC, analog to digital converter module with onboard digital filtering, designed for digitizing wide-bandwidth analog signals at 8 bits, at sampling rates of up to 1 Gsps. Buffering of the digitized data samples is provided onboard, as well as in-phase and quadrature data processing. Samples can be read f ...more

CA-102R3 is an inverting amplifier and CA-260L2/406L2 are low noise DC amplifiers. CA261F2/251F4/461F2/451F4 are a low noise amplifiers which realize high precision signal processing and high density mounting by using single-in-line package which has six-surface strict shield. ...more

The 1026 Integrated Automixer/Digital Processor combines a ten input automatic matrix mixer with a full-function, digital signal processor to provide mixing and signal processing functions in one, single rack space package. The 1026 is easily configurable and intuitive to use. The 1026 is controlled via EtherNet®, and free user software with a ...more

The MVG10 is a multiformat Video Test Signal Generator well suited for maintenance and alignment of video equipment in most television, cable. medical or video production environments. Multiple output formats Simultaneous Composite and Y/C (S-Video), RGB and Sync outputs 9-bit digital signal processing video generation ...more

PMC-SX boards use a high-performance Xilinx® Virtex-4? FPGA, but maintain a relatively low price point. They are optimized for high-performance digital signal processing to help you build custom pre/post/co-processing hardware or high-performance filters. ...more

The instrument has 12 PD channels, one power frequency reference channel and two auxiliary inputs for external temperature and humidity sensors allowing for PD correlations with external dynamics. All PD channels have identical isolated input circuitry with protection and high pass filters. The frequency band is 0.5 to 10 MHz. Advanced signal ...more

Suitable for all interfaces: analog, digital and combined. True dual-channel signal processing and generation. Recording and replaying of audio signals. User-programmable filters for analyzers and generators. Compact instrument with integrated PC. Jitter  ...more