Search Results for Routers Test
Onlineeye Pro - Router Monitor / Router Test Measure, analyze, and record the bandwidth and speed of your Internet connection. Works with DSL, Cable, Modem, SNMB enabled Router, Networkcard and any other Internet enabled device.
CAMCAD - Router Solutions Diverse challenges are arising, especially in the generation of test applications for in-circuit testing. These include various design aspects, such as the assembly of components if a board is to be tested in an in-line process, the size of the board itself, the size and position of the test points, through to the presence of test points. This goes hand in hand with the actual testability of the respective component.
RDS - Router Delay Simulator For testing network transmission delays. The Router Delay Simulator (RDS) allows Router-to-Router connections at data rates up to 2.048Mbps while simulating network delays. The user selectable delays are for both data and control signals and range from 5 milliseconds(mS) to approximately 1250 mS, in 5 mS increments. The RDS allows users to test and pre-configure Routers (with software applications)and other critical DTE equipment for reliable network operation while simulating network delay times.
RDS-LDD - Router Delay Simulator, Long Data Delays The Router Delay Simulator with long data delays(RDS-LDD) allows DCE to DTE connections at data rates up to 5Mbps while simulating network delays. The RDS-LDD allows users to test and pre-configure critical DTE equipment such as Routers (with software applications) along with an attached modem, digital service unit(DSU) or other network access device for reliable network operation while simulating additional network delay times.
SmartBits - Trusted Industry Standard for Router and Switch Testing Spirent Communications’ SmartBits enables you to test, simulate, analyze, troubleshoot, develop, and certify network infrastructure. From initial design to ongoing testing of the final network, SmartBits offers analysis solutions for all stages of a product's life cycle.
TestCenter - Highly Scalable Switch, Router and Access Testing Spirent TestCenter is a network performance analysis system that includes software and hardware components to simplify and accelerate the testing process. With Spirent TestCenter, functional and performance testing are centralized through the use of a single application that can generate control and data plane traffic and collect test results.
CDRouter - Automated Internet Protocol Test Solutions CDRouter is the networking industry's leading test solution for Cable, DSL and wireless routers. The product includes a test suite containing over 300 individual test cases. At its core, CDRouter contains a protocol engine with support for over 50 different protocols and applications.
IxAccess Test Suite - IxAccess Test Suite Ixia's IxAccess test suite provides an easy-to-use tool for comprehensive performance and scalability analysis of edge aggregation devices. By emulating PPPoX client sessions, L2TPv2 and L2TPv3 tunnels, and running data traffic over them, the testing of devices such as Broadband Remote Access Servers (B-RAS), DSLAMs and edge routers is substantially simplified.
TTsuite-IPv6 - The Test Suite for Analyzing the IPv6 The Test Suite for Analyzing the IPv6 Stack in Hosts, Routers and IPv6 Implementations. Tests for IPv6 protocol behavior and syntax variations in IPv6 messages. Exhaustive set of context parameters for flexible adaptation of IPv6 tests to the IPv6 implementation under test
IKE - Add-on Module for CDRouter CDRouter-IKE is an add-on module for CDRouter that provides IPSEC and VPN testing support to CDRouter. CDRouter-IKE is used to test IP routers that contain VPN security gateway functionality based on IKE.
ATTEST IPv6-Advanced The Net-O2 ATTEST IPv6-Advanced Test suite is a companion product of the ATTEST IPv6 Test suite. Net-O2 also offers IP routing test suites for conformance testing of Routers and Switches. Multicast test suites such as IGMP and PIM and Layer-2 bridging test suites such as RSTP, MSTP and VLAN are also available.
CheckIt Diagnostics - PC System Performance Suite Get ahead of hardware failures, prevent surprises and eliminate errors and crashes by diagnosing and troubleshooting many hardware and system problems. Fix codecs, drivers, and system software registry. Test routers, USB, FireWire® and other ports to pinpoint connection failures. Test the latest hardware and plug-and-play devices like web, video and digital cameras, wireless modems, Windows® Mobile devices, printers, scanners and more.
Network Traffic Generator and Monitor 7.6 - Network Traffic Generator and Monitor The Network and Traffic Generator and Monitor was designed to generate and monitor IP / ICMP / TCP / UDP traffic from clients to servers to stress test routers, servers and firewalls under extreme network loads. It is a very simple and fast program which can emulate true client/server activity. This application has the ability to monitor almost every aspect of network/server activities while generating traffic.
Xtramus NuStreams 2000i - Gigabit Ethernet IP Performance Test Systems NuStreams-2000i is an advanced Ethernet test system for Layer 2 to 7 and wire-speed Layer 2 and Layer 3 IP packet generation for testing of multichannel IP devices. Designed for testing in the laboratory and in manufacturing NuStreams 2000 can be easily configured for Ethernet switch, router and gateway production testing. Call for demo.
ATTEST IPv6-Tunneling The Net-O2 ATTEST IPv6-Tunneling Test Suite verifies the Neighbor Discovery Protocol over tunnel interfaces, address selection, specification of anycast 6to4 relay routers, stateless auto-configuration, mapping of IPv6 addresses into IPv4 virtual Link Layer addresses for 6over4 tunneling and compatibility with IPv4-only nodes and more…
OC-3/ OC-12c - Asynchronous Transfer Mode (ATM) Load Module Ixia's ATM Load Module enables high performance testing of routers and broadband aggregation devices such as Broadband Remote Access Server (BRAS) systems and DSLAMs. With full wire-speed IP packet generation and analysis at OC-12 and OC-3 rates, the dual-port ATM Load Module provides a cost-effective, space efficient, multi-port test environment.
Compatibility Testing With the level of sophistication in todays multi-component storage solutions, it is no wonder that compatibility is one of the top priorities of peripheral manufacturers. With numerous combinations of host adapters, switches, hubs, routers, bridges, disks, disk enclosures, tapes, changers etc. that have to work together on different operating systems with different protocols such as SCSI and Fibre Channel, there is a strong need for cross-platform, cross-protocol testing that allows for automated test runs of several combinations of components for the purposes of general functionality, data integrity and performance.
PVA-3000 - PhyView Analyzer The PVA-3000 PhyView Analyzer is designed to bridge the wide coverage gap between comprehensive Ethernet twisted pair PHY IEEE 802.3 compliance testing and simple packet verification testing. The PVA-3000 introduces an innovative multi-port capability dedicated to 10/100/1000BaseT (copper) physical layer characterization under controlled impairments including line loss, ingress noise, jittered or offset timing, and even Power-over-Ethernet. The PVA-3000 tests Ethernet switches and routers, discrete LAN interfaces, link transmission components, and network service integrity at any DTE interface.
PVA-3002 - Compact PhyView Analyzer The 2-Port PVA-3002 Compact PhyView Analyzer is designed to bridge the wide coverage gap between comprehensive Ethernet twisted pair PHY IEEE 802.3 compliance testing and simple packet verification testing. The PVA-3002 introduces an innovative multi-port capability dedicated to 10/100/1000BaseT (copper) physical layer characterization under controlled impairments including line loss, ingress noise, jittered or offset timing, and even Power-over-Ethernet. The PVA-3002 tests Ethernet switches and routers, discrete LAN interfaces, link transmission components, and network service integrity at any DTE interface.
MIMIC Simulator Suite - Powerful Network Environment Simulator MIMIC Simulator creates a customizable virtual environment populated with thousands of devices like routers, hubs, switches, probes, cable modems and workstations. Very useful for development and Testing of SNMP, NetFlow, Telnet based applications: Management application developers can implement their products quickly and test reliably at a fraction of a cost of the real lab.
The MIMIC Simulator suite includes:
MIMIC SNMP Simulator - SNMPv1, SNMPv2c, SNMPv3 and SYSLOG Simulation
MIMIC NetFlow Simulator - NetFlow, IPFIX, sFlow, SYSLOG along with SNMP
MIMIC sFlow Simulator - sFlow, NetFlow, IPFIX, SYSLOG along with SNMP
MIMIC IOS/JUNOS/Telnet Simulator - Cisco IOS, Juniper JUNOS, Telnet, SSH, SYSLOG
MIMIC Server Simulator - SMTP, DNS, FTP and SNMP
MIMIC IPMI Simulator - IPMI and SNMP
MIMIC Cable Modem Simulator - SNMP, DHCP, TFTP, ToD
This versatile suite of software tools is commonly used in:
1. Development and Testing: Management application developers can implement their products quickly and test reliably.
2. Evaluation: Enterprises can evaluate the suitability of applications with anticipated failure and growth scenarios, or qualify purchases before deployment.
3. Trade Shows: Marketing can setup powerful "live" demonstrations at trade shows.
4. Sales Demos: Sales can tailor presentations to the individual customer's environment.
5. Training Environments: Realistic training scenarios can explore all possible cases. Training environment can be portable rather than based on the classroom.
NuStreams-P9M - Network Switch and Residential Gateway Tester NuStreams-P9M is a standalone tester for testing residential gateway (IP sharing devices) with 8 LAN and 1 WAN at wirespeed. The compact and lightweight design and built-in tests make it an ideal solution for production test on production line and for analysis and troubleshooting at service centers or maintenance outlets as well. NuStreams-P9M provide Auto-Test for switch and router test.
DS-590 - XDSL Tester xDSL tester is designed for badly needed of ADSL2+ line test nowadays,it is compatible with ADSL/ADSL2/READSL. DS-590 can not only test physical parameters of line, helping user to ensure whether register the xDSL service ,but also can evaluate the service quality by transmission parameters. At the same time, DS-590 can use its imbedded Modem to finish PPPoE dialing, IE browser website by connecting with user cable. It simulates the PC+Modem way to ensure the connection between user and ISP. DS-590 goes on some network layer test after the success of PPPoE dialing, which includes Ping, Ipconfig, Router and Tracert test. Besides these, DS-590 can also replace user's PC to test the problem of broadband IP line and Modem.
Argus 145 - Combi Tester The ARGUS 145 offers an exceptionally broad spectrum of measurement functions and supports tests on SHDSL, ADSL, ADSL2 and ADSL2+ as well as POTS, U-interface and BRI accesses. The ARGUS 145 is also well equipped for checking Internet connections with IP-PING and Trace Route functions as well as download tests. In addition, the tester offers an Ethernet Through mode as well as a Router Replacement mode with support for DHCP (Client and Server).
GigE Responder - Handheld Loop Device for Ethernet testing up to GigE rate A smart handheld loop device for Ethernet testing up to GigE rate The GigE Responder provides loopback functionality in a low-cost, palm-sized platform that is the perfect companion to the SunSet MTT Ethernet and Gigabit Ethernet modules as well as the STT Ethernet, STT Metro, STT ONE modules and SunLite GigE unit. When Ethernet and IP traffic passes through a switch or router, the source and destination addresses are checked, logged, and used for directing the traffic. A simple hard loop like those used for TDM networks are insufficient for testing. Instead, a smart loop device must swap the source and destination addresses in the MAC and IP headers. With a standard, full-featured test set on one end of a circuit and the GigE Responder on the other, a technician can verify throughput, bit error rate, roundtrip delay, packet jitter (delay variation), and quality of service. The Ping and Traceroute function verifies Layer 3 connectivity for Internet access, Voice over IP (VoIP), IPTV, and other IP services.
Results 1 - 24 of 25
- Analysis (6)
- Analyzers (2)
- Bridges (3)
- Control (2)
- Ethernet Switches (4)
- Hub (2)
- Interfaces (4)
- Lab (3)
- LAN Analyzers (2)
- Loads (2)
- Modules (3)
- Monitors (2)
- Network Simulators (3)
- Services (6)
- Simulators (4)
- Software (5)
- Switches (10)
- Test Applications (4)
- Testers (3)
- Testing (14)
- »See all 53 Categories