Ground Cable Testers

The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA 568A, TIA 568B, and Token Ring cables within a few seconds. It detects miswiring, polarization, and continuity. The 230A also tests the ground of shielded twisted pair cables. With the remote unit, you can remotely test installed cable either from the wall plate or pat ...more

The Planet Waves Cable Cutter/Tester is the fast and easy helper in constructing your instrument and audio cables. Designed to work with Planet Waves RCA and 1/4” Coaxial Cables,the unit not only cuts cable with ease and accuracy, but also tests for shorts and proper tip and ground connections for 1/4” and RCA cables ...more

Test pin configuration for 10/100 base-T cable. 10base-2 cable, RJ45/RJ11 modular cables, AT&T 258A cable, EIA/%IA 568A/568B cable and TokenRing cable, etc. Verify Cable continuity, open, short and miss-wired. Test installed cable far away either on wall patch panels by using the remote kit. Auto and manual scan function. Ground wire test. Locked s ...more

The CBT-277 cable tester by Hosa is a high-quality junction box with connections for Neutrik Speakon, XLR, 1/4" phone, RCA, and dual banana, along with a comprehensive set of buttons and LED indicators that will not only tell you if a cable is wired incorrectly, but will actually differentiate between shorts, ground faults and phase mis-w ...more

This tester is designed to test in-service grounding and jumpering cable assemblies intact. This tester is designed to test in-service grounding and jumpering cable assemblies intact. ...more

This unit is designed to check the integrity of the ground cables while out in the field. It is easy to set up the STB Ground Cable Tester; and once set up, the condition of an entire grounding jumper assembly can be quickly confirmed. ...more

ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. Th ...more

There are 2 rows of 21 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connec ...more

No ground wire or clip required, safe with ECMs, Sensors, Airbags etc. Detects from 3 to 28 volts, LED light sound and vibration, rugged chrome metal construction. NEW V-groove needle accessory makes cable piercing and carrying safe. 1000?s sold. An absolute must for every technician. ...more

Wilcom T124 Cable Shield Splice Tester is an accurate measuring device which provides measurement of the conditions existing at cable shield splices, checks the integrity of ground connection, and checks the condition of capacitors across insulated splices. Two probes, capacitively coupled to the shield of the cable under test, are connected t ...more

Portable compact Multi-Operational Surge Tester that contains a multi-position carrying/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or field. The "M" is the perfect choice for your complete preventive/predictive maintenance testing - DC Hi-Pot testing, handheld resistance meter* testi ...more

The H296G Series Auxiliary Power Unit (APU) Tester allows dynamic performance testing of Garrett GTCP85 and GTCP95 series APUs and ground power units. When used with the appropriate accessory cable kit, the unit monitors engine temperature, RPM, fuel boost pump pressure and voltage, oil pressure, and it has an elapsed timer. ...more

Multi-Network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC) /10Base-T (UTP / STP) / 356A / TIA-568A / TIA-568B / Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. ...more

The insulation resistance tester IRT-S is engineerd for accurate measuring of LV-installations and appliances according the EN 61557 regulation. The tester has been developped to measure voltage, frequency and continuity. Also insulation resistance of high sensitive parts and even heavy machines or ground cables can easily be measured with the ...more

Multi-Network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC) /10Base-T (UTP / STP) / 356A / TIA-568A / TIA-568B / Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. ...more

The ISO 5000 is an electronic insulation resistance tester with a resistance range of 500kOhm to 500GOhm and an analogue indication. The instrument is engineered to measure and analyse the insulation resistance and safety of motors, machines, ground cables, transformers etc. The tester also measures AC and DC voltage up to 600 V. The logarithmi ...more

Troubleshoots cable pairs in seconds with the Tel-Line Tester. No more cutting, stripping, disconnecting & reconnecting. Plugs into 5 pin connector blocks to isolate the Central Office from the field at SLC Remotes, building entrances and Central Offices. Looks In or OUT with butt set or voltmeters. Comes with Tel Line Tester, Ground Start Cord, Lo ...more