Full Bridges

The Dual/Quad 10/100-TX Mb/s Ethernet Adapter provides up to four Ethernet connections over twisted pair media. Options are available for Front-Panel RJ45 accessibility, or Rear I/O accessibility via a VITA 36 PIM module. The card is built around Intel 82551ER Ethernet controllers that provide an integrated media access controller (MAC) and physica ...more

Portable, Low-Cost Signal Conditioning Module, Analog Input - Load Cell Input, 2 Channels, Full-Bridge Configuration, 1.6 kHz Lowpass Filter ...more

The AP10, Absolute Pressure Transducer, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full-scale output of 40 mV per volt at 3kHz. The unit operates with carrier systems including the Validyne CD15 sine wave carrier demo ...more

The Model 765 Programmable Transducer Conditioning Amplifier (PTCA) features full remote or front-panel manual control of virtually every operating function including: several excitation, signal conditioning, and calibration modes; amplifier input, output, filter and gain modes; and automatic and incremental zero and bridge balance modes. ...more

Exatron's Prototype Engineering Test (PET) Fixture is a semi-automated solution that bridges the gap between a fully automated handling system and a low cost, lower volume handler. ...more

The 4WFB120 supplies two or three legs of a "Wheatstone" or full bridge measurement for a sensor having a nominal resistance of 120 Ohms. The wheatstone bridge circuit is used to convert small changes in resistance to an output voltage.  ...more

The Trig-Tek, Inc. Model 243A Bridge Strain Gage Amplifier is designed to be used where rugged instrumentation is required, such as field measurements of vibration, shock or strain in extreme environments. Bridge excitation is fixed at 5.00 Volts and it will operate in either half or full bridge configuration. ...more

Unity gain combines with A/D gains to provide full-scale inputs from ±156 mV to ±10V. On-board precision +5V/+10V excitation source for measuring bridges, or other active transducers. Compact form factor mounts in any DBK-compatible enclosure  ...more

The 4WFB1K supplies two or three legs of a "Wheatstone" or full bridge measurement for a sensor having a nominal resistance of 1000 Ohms. The wheatstone bridge circuit is used to convert small changes in resistance to an output voltage. ...more

The simulator provides a complete suite for all your GPS simulating needs. You can: Replay your GPS logfiles. Multiplex your GPS receivers. Transform your GPS receiver interface. Bridge a remote GPS receiver. Furthermore the Skylab GPS Simulator contains a full featured interoperable OGC WMS client for receiving maps from a standardized WMS server. ...more

The DBK43A provides eight channels of strain gage input. Accommodates most bridge-type sensors, including 4-element full and 3-wire quarter bridges. Provides eight channels of strain gage input. Individual excitation regulator per channel  ...more

The DBK16 allows connection of most strain gage types to a data acquisition system. Accommodates most bridge type sensors, including 4-element full bridges. Provides two channels of strain gage inputs  ...more

Eight strain channels built-in, expandable up to 64 channels per StrainBook. Multiple StrainBooks can be synchronized for applications up to 256 strain channels. Full, half, and quarter bridge support  ...more

The 4WFB350 supplies two or three legs of a "Wheatstone" or full bridge measurement for a sensor having a nominal resistance of 120 Ohms. The wheatstone bridge circuit is used to convert small changes in resistance to an output voltage.  ...more

For monitoring strain in statically and dynamically loaded units such as cranes, presses and roll stands. Protected from harmful environmental effects. Simply bolted into place. Strain gauge full bridge ...more

The SFIN-161 SharcFIN features a set of bus interfaces and peripherals for the ADSP-21161 SHARC DSPs. it integrates a full 32-bit, 33 MHz master PCI interface, an SBSRAM controller, two I2C interfaces, eight general purpose I/O pins, and expansion bus support.  ...more

A5B38 modules plug into a backpanel to provide a single channel of analog input which is filtered, isolated, amplified, and converted to a proportional DC voltage output signal. The A5B38 can interface to full-bridge or half-bridge transducers that have a resistance range from 300 to 10K ohms. A matched pair of bridge-completion resistors (to ...more

The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solut ...more

4 strain gauges are mounted and connected to form a full bridge on a steel sensor element, in the center of the rotatable shaft. The electrical power supply for the strain gauge full bridge and the measurement signals are transmitted between rotor and stator via a high-grade, 4-fold slip ring system. ...more

This 16 channel DC source is ideal for bridge excitation where data acquisition systems are replacing traditional signal conditioners and yet full isolation and precision settable sources are requried ...more

The SFIN-101 SharcFIN features a set of bus interfaces and peripherals for the ADSP-TS101S TigerSHARC DSPs. It integrates a full 64-bit, 66 MHz master PCI interface, I2C interfaces, a peripheral bus that interfaces the DSPs to peripherals such as Flash memory, and an extensive flag and interrupt multiplexer.  ...more

The SFIN-160 SharcFIN features a set of bus interfaces and peripherals for the ADSP-21160 SHARC DSPs. It integrates a full-featured SDRAM controller, a full 64-bit, 66 MHz master PCI interface, a peripheral bus that interfaces the DSPs to peripherals such as Flash memory, and an extensive flag and interrupt multiplexer ...more

The SFIN-201 SharcFIN features a set of bus interfaces and peripherals for the ADSP-TS201S TigerSHARC DSPs. It integrates a full 64-bit, 66 MHz master PCI interface, I2C interfaces, a peripheral bus that interfaces the DSPs to peripherals such as Flash memory, and an extensive flag and interrupt multiplexer.  ...more

The CSG110 Signal Conditioner Amplifier featured with Din Rail Mount is FUTEK?s solution for in-line amplifier of any full bridge strain gauge type sensor with mV/V range output to provide VDC and/or 4-20mA signal with built-in regulated bridge excitation source. The Strain Gage Amplifier has a plastic housing with mating DB9 female connector f ...more

The SCS-824(5)(6)(7) provides 4 channels of strain gauge inputs for the SCS-800 signal conditioning system. It accommodates most strain-gauge types, from single-element quarter bridges to 4-element full bridges.  Using included SystemView software, you can adjust excitation voltage, input gain, offset nulling, and all other key functions ...more