E1

The Valid8 Megaco SIGTRAN MGC softswitch emulator allows you to test E1/T1 Media and Signaling Gateways (MG/SGs), complete calls between endpoints and test feature interaction. The package also includes protocol analysis enabling the user to capture the signaling messages that make up the call flow ...more

The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It ...more

The Valid8 Softswitch Interworking Tester allows you to test Softswitches and Gateways, Terminals, generating traffic between endpoints and test feature interaction. The package also includes protocol analysis enabling the user to capture the signaling messages that make up the call flow ...more

The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal ...more

The SuperLooper™ T1/E1 Loopback Jack and Plug quickly and easily checks the RX/TX pairs of T1/E1 circuit cables helping a network technician determine if a signal exists or if there are broken or shorted wires within the cabling. It can be plugged directly into a T1/E1 CSU/DSU or can be attached to the end of a network patch cable. ...more

The DCOSS converts any windows based PC (Windows NT/2000/XP) into a central office complete with T1 and/or E1 trunks as well as Analog and/or BRI ISDN phone interfaces. The DCOSS supports a multitude of protocols including CAS, PRI ISDN, SS7 and GR-303. The DCOSS supports manual and automated Bulk Calling and can simulate a wide variety of tra ...more

The Ultra OC-3/STM-1 card (PCI) plugs into a PC expansion slot for analyzing, testing, simulating, and monitoring OC-3 and STS-1 signals. The Ultra OC-3/STM-1 card may be used in conjunction with GL's Ultra T1 Card, Ultra E1 Card and Ultra T3 Card in the same PC to provide a complete OC-3/STM-1, STS-1/STM-0, DS3, DS1, E1 and DS0 testing soluti ...more

The T1 E1 J1 Switch provides non-intrusive failsafe monitoring and intrusive test and diagnostic capability for up to 8 full duplex T1, E1, and J1 lines. The unit provides two RJ-48c connectors for a thru connection for equipment and line connections and a Rj-48c monitor connector for monitoring both directions of a full duplex high-speed line ...more

GL's PPP Analyzer can be used to capture a host of PPP protocols exchanged between the two nodes over T1/E1 link. User can obtain detailed analysis of the protocol and can perform various statistics measurements. ...more

GL's GSM Analyzer is used to analyze GSM protocols, a switching and signaling telecommunication protocol between MSC & BSC, BSC & BTS, MSC & HLR, MSC & VLR, etc. and operates on T1 & E1 channels ...more

GLs new USB based T1 E1 Analyzer is the world's most powerful, full featured, and complete BERT, voiceband, data, signaling, and protocol analyzer on the market. It can perform analysis and emulation of various signal types including voice, digits, and tones; various protocols including HDLC, ISDN, SS7, CAS, Frame Relay, GSM, GPRS, CDMA, and U ...more

The ULTRA T1 (E1) Card transforms your PC into a sophisticated T1 or E1 analyzer. Prior versions of the Ultra T1(E1) Cards were designed for use in ISA slots, and the current Ultra T1(E1) cards are PCI. The newer PCI versions are available with either a single T1 (or E1) interface or with a dual T1 (or E1) interfaces. ...more

The GL's UltraT3 Cards (PCI) plug into PC expansion slots and provide digital T3 input/output for analyzing, testing, simulating, and monitoring T3 signals. A single T1/E1 input and output is provided to insert and receive T1 (or E1) signals into the T3 stream. The cards provide the capability of generating 28 DS1 or (21 E1) signals within the ...more

Multi-channel Bit Error Rate Testing (MCBERT) measures correctness of data received on T1/E1 lines/timeslots with stored data in a reference file. The application can work in real-time with data currently being received on T1/E1 lines/timeslots, or off-line with data stored in a file. The on-line T1/E1 testing can be done on full or fractional ...more

GL's HDLC protocol analyzer provides the capability to capture, and analyze HDLC data on a full duplex T1 or E1 line. The data channel may utilize all or a fractional part of the T1 or E1 line. ...more

The Valid8 Megaco SIGTRAN MG/SG emulator enables testing E1/T1 Media Gateway Controllers (MGCs), completing calls between endpoints and testing feature interaction. The package also includes protocol analysis enabling the user to capture and verify the signaling messages that make up the call flow. ...more

GAO5854 E1 / Datacom Tester is a multi-functional and full- featured digital transmission system test device, designed for the installation test, engineering check and acceptance, daily maintenance of digital networks. Mainly performing channel test, alarm analysis, faultfinding and signal analysis. In addition, this instrument further provide ...more

GAO2018 E1 BER (Bit Error Rate) Tester is a much small and multi-functional handheld E1 line test instrument , specially designed for E1 PCM line access, maintenance, check and acceptance. It provides BER test, alarm analysis, signaling analysis and so on which can be extensively used in R&D, production, installation and maintenance of SDH ...more

The TSP Edge gives you high-end telecom test system power in an affordable and scalable package. Offering T1, E1, PRI (North America and Euro protocol) and POTS simulation, extensive programmability, scripting, and more, the TSP Edge is ideal for feature and performance testing applications in R&D, QA, production, demo and training environments. ...more

RT-2X is a fast 2-channel voice frequency test system for telecommunication testing. It comprises analog and digital interfaces (POTS, ISDN, T1, E1, J1, PCM) with the capability to evaluate all important performance parameters of a telecommunication device within fractions of a second. ...more

Simline 6 is our popular multi port ISDN network simulator with 6 basic rate ports (S/T interface) and one optional primary rate port (E1 interface). Simline 6 can be used with routers, PBX, video conferencing terminals (128K and 384K), terminal adapters, PC applications or any ISDN terminal fitted with a standard S/T interface or a primary ra ...more

Converts HDB3-encoded E1, E2, and E3 signals into logic NRZ data and clock. Front panel and RS-232 selection of input HDB3 and logic types and input logic rate. Dual outputs (splitter function) of the HDB3 and logic signals ...more

The equipment under test (EUT) needs modification if functional faults occur in burst and ESD pulse tests on electronic modules and devices. The E1 development system is used to quickly and precisely determine the causes of functional faults within the EUT. The user is able to find out how and why the individual conducting tracks and components ...more

BATTERY TESTER  ...more

Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment. ...more