Analyzer Probes

The GenisysTM emissions repair solution. Kit includes the plug-in Performance 5-Gas Analyzer Module, hose, probe, Gas M-P software, regulator, filters, manual, and carrying case. ...more

Electric field analyzers for low frequency fields, selective and broadband measurements. EFA-200 is for measuring magnetic fields. EFA-300 is for measuring magnetic and electric fields. Isotropic measurement with integral test probe and external standard 100 cm2 probe (accessory) or in case of EFA-300 with electrical cube ...more

Accurately Measures Load V, I and Phase Angle for RF plasma optimization Utilizes Advanced DSP Technology for Real Time, User Programmable Data Acquisition Wide Frequency Range No Dedicated PC Required for Data Gathering and Control, Minimal Insertion Loss ...more

The XT residual gas analyzer (RGA) from Extorr offers exceptional performance and value. These RGAs provide a more detailed vacuum gas analysis than is offered by any other single competitive device. Each system comes complete with a multi-gauged quadrupole probe, a control and communications unit (CCU), and a real-time Windows® software package. ...more

CAYLAR manufactures custom magnets for Mass Spectrometers (Magnetic Sector), Small Ion Source Generators (Magnetic Mass Analyzer, Deflectors), equipped with Vacuum Segment and probe of NMR or Hall Effect Gaussmeter or Field Regulation. A specific application is Characterization Bench for Magnetic sensitive components, with dedicated devices : Therm ...more

The Datatest Model DT3001 is paramagnetic microprocessor based oxygen analyzer. The DT3001 comes with two different probe configurations for temperatures up 1500°F and 3200°F. The microcontroller provides long-term stability and reliability plus features for controlling back purge, calibration gas injection and self-calibration. 4 - 20 mA output an ...more

The Solarity emissions repair solution kit includes Solarity, with plug-in 5-Gas Analyzer Module, hoses, exhaust probe, power cable and battery adapter, RS232 cable, AC power supply, Smart Card, Gas M-P software CD, filters, manual, and carrying case. ...more

M4000 is a multifunction analyzer of ambiental parameters with singol probe to measure temperature of the air, relative humidity of the air, speed of the air, air volume, capacity and dew point. The instrument is particurarly suitable to check conditioning installation  ...more

6U-CPCI Passive Extender Full height allowing the user to extend the CPCI bus out of the chassis for troubleshooting and probing of 6U CPCI UUTs. J1 and J2 routed in accordance with the CompactPCI 64-bit specification J3, J4 and J5 routed straight thru. Easy accessible test points are provided for all 6U CPCI bus signals for connection to scop ...more

The NP7100 Ranger Network Probe is a multiple WAN protocol test and analysis equipment in a single, rugged, package. Comprehensive T1/E1 testing High-speed BERT to 2.048 Mbps Data line monitor with auto configure, lead status VT-220 terminal emulation Remote control Dual Channel Oscilloscope DVOM, continuity tester, dB level meter Built-in har ...more

64 bit Hot Swap PCI Extender Card 3.3V<=>5V Signal Level Conversion Allows PCI Mezzanine cards to be tested in the PCI bus. Bank Switch isolation, allowing the user to isolate groups of signals for troubleshooting purposes. ...more

The ELAB-080 is an integrated instrumentation package that uses the power of modern PCs to provide powerful test and measurement features at a very affordable price. The ELAB-080 package comes complete and ready to use with the instrument, power supply, two oscilloscope probes, logic analyzer and AWG cabling, software, and a USB cable. All you need ...more

The Datatest Model DT3006 Oxygen/CO analyzer is a microprocessor based instrument. It has a zirconia sensor for oxygen and an electrochemical sensor for carbon monoxide. Excellent trim control and boiler safety instrument with great reliability and stability thanks to the micro controller. ...more

Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current. ...more

The Agama Analyzer is a software based transport stream monitoring probe supporting simultaneous monitoring of hundreds of IPTV streams. By monitoring multicast or unicast IPTV streams and analyzing the full DVB and ATSC over IP stack it detects errors on all protocol levels, from the network layer to the video layer. ...more

STARAcoustics is a complete acoustic intensity program for use with multi-channel FFT instruments or real-time octave analyzers and microphone probes. Acoustic intensity analysis enables you to: Quickly identify noise sources. Accurately determine the sound power radiating from noise sources. Acquire measurements in acoustically noisy environments ...more

The Datatest Model DT3008 Combustibles analyzer is a microprocessor based platinum catalytic bead sensor instrument available with three different probe configurations for temperatures up 750°F, 1500°F and 3200°F. Perfect for safety monitoring for boilers and combustion processes where dangerous combustibles levels are possible.  ...more

The X-COM NTDS Protocol Analyzer System reaches a new level of protocol analysis capability by providing insight into protocol, error, timing, and waveform analysis. The system includes an X-COM NTDS Type E Protocol Interface Module, a Tektronix TLA5000 Series Logic Analyzer, two TLA P6434 Probes, and custom disassembler software. ...more

This network monitor and protocol analyzer is the ultimate application for traffic-level network monitoring, troubleshooting, analysis, and visualization. If your network is crawling to a standstill, and you suspect there might be a problem with the network traffic, Network Probe will quickly help you identify what is causing the problem, show you ...more

The Datatest Model DT3000 is a Zirconia sensor, microprocessor based, oxygen analyzer. The DT3000 comes with probe configurations for temperatures up to 3200°F. The microprocessor based controller provides long-term stability and reliability, plus optional features for controlling back purge, calibration gas injection, and self-calibration. 4 - 20 ...more

6U, VME Hot Swap Extender Auxiliary measurement point for +5V current measurement, using a voltmeter. Short circuit protection Power may be controlled via Mechanical Switch or Remote TTL/CMOS Signal Automatic VME daisy chain signal pass through when extender is powered off, allowing for continued system operation Easy accessible test points ar ...more

The is based in an all-optical method without O/E conversion and electrical post-processing until the light reaches the photodiode. The incoming signal under test (SUT) interacts with the beam of the known local oscillator (a TLS, used as probe) in a perfectly known material medium. Deterministic and calibrated non linear effects dominated by the ...more

AgriSpec ? the rugged, field portable Vis/NIR analyzer (shown right with the Plant Probe and Leaf Clip Assembly) designed specifically for analysis of a wide range of organic and inorganic materials, including nutrient and moisture properties in soil, monitoring the composition of manure and other biosolids applied as fertilizer to agricultura ...more

The probes for RF voltage and current measurement are directly connected to a spectrum analyzer. The probes which contain a pre-amplifier are supplied via a plug-in power supply unit. ...more

SM5011 spectrum analyzer is used for the early test in the development of electrical products, troubleshooting of CATV/MATV system as well as the test and trouble diagnosis of cellular phone/paging systems. Combined with the near field probes of Mz530, it can detect the missing fields of radio frequency. ...more