Filter Results By:

Products

Applications

Manufacturers

Voltage

The tension of an electromotive force.


Showing results: 5086 - 5100 of 6464 items found.

  • High Resistance Meter

    HR2 - Alpha Lab, Inc.

    The Model HR2 meter measures resistance in nine ranges from 1 ohm to 1.9999 Tera ohms (1.9999x1012 ohms), and conductance in a single range of 0.00 to 199.99 pS (pico siemens, or pico mhos), all at low voltage of < 2 volts across the sample. Basic accuracy is +/- 2% of reading +/- 1 count. For resistance higher than 1.9999 Tera ohms, the conductance range can be used to measure conductance down to 0.01 pS (100 T ohms). The meter has a conductance range because samples with simultaneously high resistance and high capacitance settle faster to their final value on conductance (usually under one second), than on resistance (several seconds), and conductance is also capable of detecting higher resistance than the resistance ranges can. Note that resistance in units of T ohms is the inverse of conductance in pS, so that the resistance can be calculated from the conductance. For example, 100 pS is 0.01 T ohm (10 G ohm), and the highest readable conductance of 199.99 pS is essentially 5 G ohms.

  • PIN Photodiode

    Appointech, Inc.

    PIN photodiode is a kind of photo detector, it can convert optical signals into electrical signals.This technology was invented in the latest of 1950's. There are three regions in this type of diode. There is a p-region an intrinsic region and an n-region. The p-region and n-region are comparatively heavily doped than the p-region and n-region of usual p-n diodes. The width of the intrinsic region should be larger than the space charge width of a normal p-n junction. The PIN photo diode operates with an applied reverse bias voltage and when the reverse bias is applied, the space charge region must cover the intrinsic region completely. Electron hole pairs are generated in the space charge region by photon absorption. The switching speed of frequency response of photo diode is inversely proportional to the life time. The switching speed can be enhanced by a small minority carrier lifetime. For the photo detector applications where the speed of response is important, the depletion region width should be made as large as possible for small minority carrier lifetime as a result the switch speed also increases.

  • Fuel Display Unit Tester

    MS 1125 - Meltronics Systemtech

    Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit.  FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.

  • Turns Ratio Testers

    TRT Advanced Series - IBEKO Power AB

    TRT Advanced series is the newest DV Power solution for transformer turns ratio measurement. Besides its main application, each turns ratio tester from this series also measures transformer excitation current and phase shift. Furthermore, all models perform automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. They have a built-in true three-phase power source. For that reason, they can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 500 V AC, depending on the model. With the highest test voltage 500 V AC, TRT500 provides the most accurate turns ratio testing of power transformers used in power generation and transmission. The output test voltage of TRT500 can be boosted to 5 kV AC using the external CVT20 extension transformer. This application is specially designed for testing turns ratio of capacitive voltage transformers. The other three models, TRT400, TRT250, and TRT100 can output up to 400 V, 250 V, and 170 V respectively. The low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT500 is equipped with a large 10.1” graphical touch screen display. Other models, (TRT400, TRT250, TRT100) have 7” graphical touch screen display. Besides making the interface much more user-friendly compared to older turns ratio testers, it also brings certain options that were previously available only with DV-Win software. The most important are test templates and automatic test mode. Users can simply create test templates, store them in the instrument’s memory, and load when in the field with just a few clicks.This turns ratio test set, as well as all other DV Power turns ratio testers, has a built-in tap changer control unit. It enables remote control of an on-load tap changer (OLTC) directly from the instrument. In order to make the most out of this feature, the instrument can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time. Automatic test mode minimizes human errors, which makes the measurement more reliable.

  • Frequency & Phase Converters, 400 Hz Isolated Input; Optional UPS, Rackmount – 1kVA to 5kVA

    ED-M Series - Falcon Electric, Inc

    *Isolated 400Hz, Three-Phase Input; Single-Phase Output*Eliminates Phase Imbalance and Associated Harmonics*50, 60 or 400Hz Operation and Frequency Conversion*Superior Output Voltage Regulation*Pure Sinewave Output*True Double Conversion Design*Wide Operating Temperature Range*Military Rugged, Lightweight Rackmount Design*External Battery Bank Options for On-line UPS Operation

  • High Power Digital Lab Series Regulated DC Power Supply – 3000W

    Aplab Limited

    - 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting

  • Load Monitoring Units (LMUs)

    Magtrol Inc.

    Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability

  • 3kW Electronic Load

    PT04-FC - Manatronics Pty Ltd

    For Fuel Cell testing and Power Supply testing. This model has been developed to accommodate testing of both Fuel Cells and low Voltage Power Supplies, (including 24V telecommunications power systems or Power Supplies). It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.

  • Thermal Imaging Sensor

    3550 FC - Fluke Corporation

    Condition monitoring sensor to visualize thermal patterns on multiple assets. Maintenance managers can now collect a more comprehensive variety of key-indicator data — thermal imaging, voltage, current, temperature, and power — on critical equipment to build a real-time picture of an asset's condition. With the right mix of data all in one place, managers can implement planned maintenance and decrease the frequency of preventive rounds.

  • CTEK Battery Analyzer

    56-925 - CTEK Power USA

    The CTEK BATTERY ANALYZER tests with high accuracy the condition of all types of 12V lead-acid batteries including Wet, Maintenance Free, Ca/Ca, Gel and AGM. Easy to use it provides fast, and easy to understand results. Operating voltage range is 8–15V with a test range of 200–1200EN. Simply connect the clamps to the battery and follow the step by step instructions on the display.

  • Air Core Shunt Reactors

    Hilkar

    Shunt Reactors act as absorbers of reactive power to increase energy efficiency of the power system. Shunt Reactors are inductors that are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. The shunt reactors provide inductive compensation.

  • Electrical Testing

    Innovative Testing Solutions, Inc.

    Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.

  • Bridge Decking Testing Equipment

    Buckleys Ltd.

    The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.

  • Battery Analyzers

    Junxy Energy

    JUNXY battery internal resistance & conductance tester is a portable and hand-held battery test and measurement instrument for daily battery maintenance. It offers users a fast and reliable principle to on-line check groups of battery bank’s battery state of health (SOH), battery performance by quickly and precisely testing each cell voltage, internal resistance, conductance, connecting strip resistance and so on.

  • Multifunction Electrical Installations Meter

    MPI-520S - Sonel S.A.

    The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.

Get Help