Showing results: 2131 - 2145 of 2454 items found.
-
DMC-52xx0 -
Galil Motion Control, Inc.
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
-
Model No. 11615-50 -
Aero Instruments & Avionics, Inc.
The Aero Instruments & Avionics 11615-50 Portable Data Loader (PDL) provides proven ARINC 615-3/ARINC 603 load technologies with additional ARINC 615A over Ethernet capability. This new addition to our product line is ideal for aircraft fleets preparing to use, or that are currently using 615A loadable equipment. Avionic data loads can be performed from Floppy Disk, CD, DVD, USB, or the internal solid state Mass Storage Device (MSD). The MSD can be loaded in advance to eliminate the distribution of disks/memory devices to airplanes while significantly reducing the time to perform the data load tasks. External media is verified before any load is executed. This saves valuable ground time by alerting the operator of any bad media before attempting the load. Our 11615-50 PDL is easy to read and easy to use. All functions are performed using the high resolution 5” TFT LCD display and four large “Soft Buttons”. Together, they provide simple navigation to the selected loadable software and straightforward load status messages. Call Jim Krey for a quote: 716-694-7060 ext. 322
-
CAPA315 -
Axiomtek Co., Ltd.
The CAPA315 is powered by the Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake). It comes with various I/O connectors and flexible expansion features within its 146 x 104 mm dimensions. The CAPA315 also has an extended operating temperature range of -20°C to 70°C to withstand the rigors of day-to-day operation. The 3.5-inch CAPA315 has one 204-pin DDR3L-1867 SO-DIMM for up to 8GB system memory. Furthermore, it comes with one RS-232/422/485, three RS-232, two USB 2.0, four USB 3.0, 8-channel digital I/O, HD Codec audio and dual Gigabit LANs with Intel® i211AT Ethernet controller. For storage requirements, it has one SATA-600 and one mSATA. Moreover, the low power embedded platform runs on +12VDC power, supporting auto power-on. For connectivity, this embedded board has a PCI Express Mini Card slot for 3G/4G, GPS, Wi-Fi and Bluetooth connections. To ensure reliable operation across platforms, the 3.5-in embedded board also supports watchdog timer, hardware monitoring functions and Trusted Platform Module 1.2 (TPM 1.2).
-
PICO318 -
Axiomtek Co., Ltd.
The PICO318 is powered by the Intel® Pentium® processor N4200 or Celeron® processor N3350. The PICO318 is a low power-consumption 2.5-inch embedded board that is expandable, rugged design, feature-rich and versatile to help facilitate quick deployment. The PICO318 is equipped with one 204-pin DDR3L-1867 SO-DIMM for up to 8GB system memory. A dual-display capability is available through 18/24-bit single/dual channel LVDS and DisplayPort. For storage, there are one M.2 key B slot for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot with support for mSATA. Moreover, the pico-ITX form factor single board computer features 12V DC power supply input with AT Auto Power On function. The Intel® Apollo Lake-based pico-ITX board provides rich I/O connectivity including two USB 3.0 ports, two USB 2.0 ports, one RS-232/422/485 port, one RS-232 port, two Gigabit LAN ports with Intel® i211AT Ethernet controller, one HD Codec audio, and 4-channel digital I/O. The PICO318 is suitable for various industrial environments with an operating temperature range of -20°C to +60°C.
-
Extech MO280-RK -
Extech Instruments Corporation
The Extech MO280-RK Restoration Contractor's Kit is a complete solution for the restoration contractor. This kit uses pins and pinless meters to better diagnose the amount of moisture content in a certain material. The thermal hygrometer provides a fast and accurate reading of ambient room conditions and GPP calculations. This kit is a supplied in a rugged hard carrying case. Kit includes the MO280 Pinless Moisture Meter which displays 0 to 99% moisture from a selection of 10 different wood types. The measurement surface depth is 0.75 of an inch with virtually no surface damage. MO220 Wood Moisture Meter comes with integral pins and a remote pin probe that displays up to 99.9% of the moisture level with 8 different wood types with calibrations for approximately 170 wood species. Kit also includes the RH490 Precision Hygro-Thermometer which has a 2% RH accuracy and a fast 30 second RH response time. Measures humidity, temperature, dew point, wet bulb, GPP and g/kg. The Extech MO280-RK Restoration Contractor's Kit also includes the RHT10 Humidity and Temperature USB Datalogger that records up to 16,000 readings each of RH and temperature. The USB interface and software is included in the kit.
-
MS 1508 -
Meltronics Systemtech
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
IT9100 Series -
I-TECH Electronic Co., Ltd
The IT9100 power meter can provide the maximum input of 1000 Vrms and 50 Arms and measurement bandwidth of 100 KHz, and can be easily used for measuring thevoltage, current, power, frequency, harmonics and other parameters. The standard configuration includes USB, GPIB, RS232 and LAN communication interfaces and also interfaces for USB-based peripheral devices. Users can save the measured parameters into the external storage medium. The basic voltage and current accuracy is 0.1%. Moreover, the power meter has rich integrating functions, such as the active power. It is widely applied in test of motors, household appliances, UPS, etc.
-
PRS-812B -
Prostat Corporation
- Wide Range Resistance: 0.10 Ω to 1.00x1012 Ω- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Constant Test voltages 10V and 100V for specification measurements to meet international and domestic ESD measurement standards- Auto Resistance Range Control- Auto Test Voltage Control- Uses a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- 120 Data Set Internal Memory- Uses Standard USB Cable for Charging- Charges in 2 Hours- 2-year Limited Warranty on Main Instrument
-
TMR9112 -
MultiDimension Technology Co.,Ltd.
The TMR9112 demo board was developed to support evalution of the TMR9112 single-axis sensor. The demo board comes with the fast bipolar current pulsing circuit needed for initialising the TMR9112 sensor, and it can be powered from a USB port or any external 5V power supply. For user convenience, the demo board has an optional on-board timer clock with four selectable frequency settings. The On-board timer clock and frequency output can be enabled using the jumper pins. This demo board is divisable along the dotted line so that the sensor board can be seperated from the pulsing circuit board.
-
PEAK gridARM Evaluation Board -
PEAK-System Technik GmbH
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
FemtoFiber dichro midIR -
TOPTICA Photonics Inc
The new FemtoFiber dichro midIR represents an ideal laser source for mid-infrared spectroscopy and imaging. It provides a tunable broadband output in the wavelength range of 5 to 15 m (20 - 60 THz, 670 - 2000 cm-1). The unique 400 cm-1 broad emission spectra allow to excite a wide range of materials at the same time. The air-cooled system is based on TOPTICAs proprietary fiber laser technologies and includes a difference frequency generation (DFG) unit as well as all necessary electronics into the same box. All functions and features are computer controllable by Ethernet or USB interfaces.
-
CM12001 -
LinkedHope Intelligent Technologies Co.,Ltd.
CM12001 integrates the complete functionality of vertex86DX,offering a CPU, system BIOS, 16bit DRAM up to 512MB, keyboard controller, real-time clock, and IDE compatible onboard Flash hard disk up to 16GB. The solution includes a highly integrated embedded CPU chip made by DMP. It has x86 Compatible Processor Core.This module is designed for embedded applications. The pin out of its’ Dimm-pc bus connector corresponds in large part to the pin out of a standard ISA bus. It offers peripheral functions such as USB, PS2, LPT, COM interface...
-
Talon RTS 2580 -
Pentek, Inc.
- The Talon® QuickPac® drive can be removed from a Talon RTX - SFF recorder and inserted in this offload system- Allows the Talon recorder to remain deployed in the field- Data stored on the QuickPac drive can be accessed and offloaded for analysis- Designed for Talon models RTX 2586, 2589, 2590, 2596, and 2684- Can offload data to removable SATA drives, DVD, Ethernet and USB ports- 4U 17-inch PC server chassis, 21 inches deep- Windows® workstation- Intel® processor- 8 GB DDR SDRAMSystemFlow® Software
-
VT-96 -
Holding Informtest
Thermal station VT-96 is intended for building data collection systems (distributed and remote) from thermocouple temperature sensors. The interfaces allow you to easily and quickly connect the VT-96 to a remote (via ETHERNET) or nearby computer (via USB). The integrated WEB-page provides a convenient way to check the communication with the unit and its functioning, and the standard VXIplug & play drivers reduce the costs of integrating the unit into the system and developing application software. Multiple thermostats easily integrate and synchronize with each other and other VXI instruments via a dedicated Trigger Bus.
-
ANET3910-EN -
AIM GmbH
STANAG3910 Electrical Test and Simulation module for Standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create run-time applications to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
