Filter Results By:

Products

Applications

Manufacturers

Showing results: 841 - 855 of 5411 items found.

  • SparkFun Air Quality Sensor

    SGP30 (Qwiic) - SparkFun Electronics

    The SparkFun SGP30 Air Quality Sensor provides information on the quality of the air in your room or house by monitoring the volatile organic compounds around the sensor. The SGP30 Air Quality Sensor can return valid indoor air quality (IAQ) readings within 15 seconds of powering up! By comparison, typical air quality (IAQ) sensors are great for measuring CO2 and volatile organic compounds (VOCs) but some of them require a burn-in time of 48 hours and a 20-min start up time.

  • Universal Counter

    U6220A - PICOTEST Corp.

    The Picotest U6200A also provides great features including Frequency & Ratio (11Digits/Sec.), Time interval, Period (2.5 ns to 1000s), Duty Cycle, Pulse Width, Rise/Fall Time, Peak Volts (100 Hz~300 MHz), Phase, Totalize, Temperature Stability (< 1 PPM), Aging Rate (< 2 PPM per year), timebase reference channel (Figure-2) and complete Front-End Isolation. Moreover, it offers 20 memory locations (Figure-3) for storing frequently-used operations.

  • Xineos Large Area Detectors

    Teledyne DALSA

    As a leader in CMOS innovation, Teledyne DALSA developed the Xineos to deliver three times more sensitivity and five times more signal-to-noise performance than other standard technologies at equal X-ray dose conditions. CMOS image detectors offer numerous advantages including the ability to record smaller image details with higher resolutions – allowing for the diagnostics of medical anomalies at earlier stages, and significantly increasing the probability of early intervention, patient recovery, and reduced treatment costs.

  • Xineos Scanning

    Teledyne DALSA

    Teledyne DALSA's leadership in CMOS innovation lets our Xineos scanning products deliver three times more sensitivity and five times more signal-to-noise performance than other standard technologies at equal X-ray dose conditions. CMOS image detectors offer numerous advantages including the ability to record smaller image details with higher resolutions – allowing for the diagnostics of medical anomalies at earlier stages, and significantly increasing the probability of early intervention, patient recovery, and reduced treatment costs.

  • Ionization Test Set

    PFK-105 - Prostat Corporation

    - Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included

  • 4D Imaging Radar Chipset Solution

    Arbe Robotics

    Through enhanced FMCW technology, Arbe’s chipset technology transmits and receives signals from multiple antennas. By converting information from time to frequency domains (FFT), Arbe provides a 4D image with unparalleled element density in high azimuth and elevation resolution while simultaneously sensing the environment in long range with a wide field of view in real time. Additionally, Arbe technology reduces sidelobe occurrence levels close to zero, resolving range-doppler ambiguities and avoiding interference from other radars.

  • Digital Fiber Sensor

    FX-500 Ver.2 - Panasonic Industrial Devices Sales Company of America

    Thanks to its new “application-specific integrated circuit” (ASIC), Panasonic can solve applications with Fiber Optic Sensors that were previously impossible. Not only can the FX-500 Series reach a response time of 25µs while providing extremely accurate detection, integrated logic functions save you money because external controllers are no longer needed for normal applications and threshold tracking and self-diagnostic functions save time for maintenance. Moreover, the reliability of the detection has increased by 75% compared to that of previous models.

  • Immersion Testing

    National Technical Systems

    Immersion testing evaluates how well your product or component will hold up when submerged in water or other liquids. This is not limited strictly to waterproofing — other factors, such as the ability to withstand rapid changes in pressure or exposure to caustic chemicals, can also be made a part of testing. As a result, immersion testing is an investment in more robust and durable design. By taking the time to test these factors early in the development process, you can create an all-around better product and shorten your time to market.

  • Rebar Locator

    Profoscope + - PASI srl

    The Profoscope+ is a fully integrated rebar locator with data storage. To increase the efficiency on the construction site this enhancement of the Profoscope not only offers real time visualization of rebars, but also automatic data collection. Writing down measuring results of testing series is a time consuming business that can be an unnecessary source of errors. The various data storage modes of the rebar locator Profoscope+ make note taking obsolete. This cordless rebar detector is ideally suited for one-handed operations, keeping the other hand free for marking rebars.

  • Patented GPS Jamming and Spoofing Detection Embedded in Your Device

    BroadShield - Safran Federal Systems

    PNT systems are designed to provide accurate position and time while in uninterrupted or uncontested environments. However, while in these interrupted or contested environments, most PNT systems are unable to reliably provide position and time data because they are unable to recognized what is causing the disruption. BroadShield is a software library consisting of many patented algorithms designed to detect jamming and spoofing then immediately report the disruption to the PNT system. Leveraging this information enables the PNT system to take action to mitigate and protect from the jamming or spoofing.

  • Precision Machining

    Teledyne OEM Solutions

    Several of our facilities have extensive in-house machining capabilities, with high-end automated systems that allow us to maintain strict control over the quality and delivery of our products, as well as managing costs. This means that we don't have to coordinate with outside suppliers or pass on any additional costs to our customers. Our experienced machinists use modern equipment to produce precision parts and components quickly and efficiently, ensuring that our customers receive the highest quality products on time, every time.

  • Condition Monitoring

    M+P International

    m+p Coda is a versatile monitoring system that captures and records signals coming from sensors such as accelerometers, thermocouples, strain gauges, and pressure transducers. Limit checking and alarm monitoring is provided for every active channel. The active channels are clearly displayed in a separate window, out-of-limit data can be seen at a glance. Alarm events are entered into a log file and can be reviewed at any time. You have the option to change the alarm limits online at any time without stopping the data acquisition.

  • Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces

    M8KDiscrete - Excalibur Systems, Inc.

    The M8KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M8KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports ten programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each.

  • Laser Radar shop floor CMM

    Nikon Metrology, Inc.

    With the need for shorter and more flexible production cycles, automotive manufacturers are continuously looking to cut time and costs whilst improving product quality. The Laser Radar mounted on an industrial robot introduces an innovative approach to body-in-white (BIW) inspection. This shop floor system provides accurate, dimensional measurements in the car coordinate system allowing direct comparison to CAD without the need for a reference part. Unlike horizontal-arm CMM, its high-speed measurements fit within short production cycle times.

  • DIP LED Aging Tester

    LS6100 - Lisun Electronics Inc.

    Designed to measure the aging-life and color comparisons of 260pcs DIP LED. • 260 separate constant current supply • Aging functions: constant current, impact pulse, on-off mode • Range of forward voltage(VF): 5.0V • Range of forward current(IF): 1) constant current: 0-100.0mA 2) Impact pulse: 0-200.0mA • Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99% • Range of on-off circle: 0-9999H59M59S • Range of on-off times: 0-9999times • Range of aging time: 0-9999H59M59S

Get Help