Showing results: 2926 - 2940 of 5355 items found.
-
ReaXus -
Teledyne LABS
Teledyne LABS ReaXus® reciprocating pumps covers a broad range of application needs, ranging from 5 mL/min to 300 mL/min and up to 6,000 psi. Whether you need low pulsation or are working with hazardous materials, the ReaXus line has an option for you. The single piston models are targeted towards moving material or providing pressure. The dual piston models are focused on continuous processing applications where a steady flow of material is important.The ReaXus product line is low maintenance and requires no calibration like other styles of pumps, saving your organization time and money.
-
N9030A-RT2 -
Keysight Technologies
Capture elusive signals as short as 3.57 with 100% POI and a complete set of advanced triggers View signal dynamics with displays: digital and swept density, spectrum, spectrogram, power vs. time, gap-free real-time analysis, and more Maximize your investment by adding RTSA to your PXA at a fraction of the cost of a dedicated solution Easily integrate the 89600 software and thoroughly analyze complex signals Extend RTSA measurements to millimeter-wave range with external mixers Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
R347B -
Keysight Technologies
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
E9304A -
Keysight Technologies
Refer to the E9301A for standard power sensor features Low frequency coverage (9 kHz to 6 GHz) for EMC/EMI test applications such as the radiated immunity test (IEC61000-4-3)High sensitivity (-60 to +20 dBm) and fast measurement speed to reduce the time taken to calibrate radiated field uniformity and EMC/EMI test receivers Measure transmitter power and receiver sensitivity at Very Low Frequency (VLF) to microwave frequencies Special option available to 18 GHz Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
RapiCoverZero -
Rapita Systems Ltd.
*Collect coverage from systems that produce branch traces*Save time with efficient merge and mark verification workflow*Simplify verification through integration with your CI tool*Collect coverage for libraries without source code
-
MSPG-2000 -
Master Co. LTD
MSPG-2000 Video Signal Generator, was designed to test standard Panel and Multimedia Video Signal. Separated four(4) boards generate selected own(1) Time & Pattern and output to the each section with two(2) ports.
-
Freese Enterprises Inc.
Several examples of our automatic test equipment expertise can be found below by clicking on each description in the table. For more information on a custom automated system design for your application, a fixed price quote, or time and materials rates.
-
Scorpion ILS 1000 -
Terotest Systems Ltd.
Acculogic's Inline Scorpion is a fully automated in-circuit test system for high volume production with the added advantage of a very fast change over time for different assemblies - less than one minute, including fixture change.
-
Acculogic, Inc.
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
CyberOptics Corporation
Lowering Cost of Quality and Speeding up time to market, CyberOptics’ high-precision 3D scanning inspection systems with metrology-grade accuracy have helped customers successfully complete their most complex inspection, analysis, and reverse engineering projects.
-
HIOKI E.E. Corp
IP67 protected top in the industry Test all ground types from Class A to Class D with a single meter Wide 0 to 2000 measurement range Minimize cabling time with innovative earthing rods and cable winder
-
Schwarzbeck Mess Elektronik
Biconical Antennas have dipole like characteristics (e.g. circular directional pattern in the H-plane,"8"-shaped in the E-plane, fixed phase center, comparable gain), with an enormous wide bandwidth achieved by the double cone elements. One of the earliest and worldwide most popular biconical antenna designs is the BBA 9106 with balun VHA 9103 B. During the last years a growing need for expanded frequency ranges arised, which led to the design of biconical antennas reaching down to frequencies of 20 MHz and up to 18 GHz and above. A further increase of bandwidth was achieved with qualified 4:1 baluns, providing a typical gain increase of approx. 6 dB at the lower frequency range. The biconical elements can be mounted and dismounted within a few seconds providing perfect contact repeatability thanks to special clamping fixtures. A small wrench made of insulating material is supplied with the balun, it is tied to the balun head and thus always available whenever needed. Biconical antennas can be used for many applications, in which half-wave dipoles have been used traditionally. An enormous reduction of measurement time can be achieved, because the time consuming tuning of the antenna elements to the half wavelength is not needed, an important condition for sweeped broadband measurements. In typical dipole applications several discrete frequencies are measured, in contrast the biconical antenna allows continuous sweeps, where site anomalies are discovered much easier.
-
UXI-1553 -
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
781720-01 -
NI
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), Up to 12 GB/s PXI Chassis - The PXIe‑1086 incorporates hot-swappable, redundant AC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086 monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
780683-02 -
NI
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
