Filter Results By:

Products

Applications

Manufacturers

Showing product results. 5011 - 5025 of 5372 products found.

  • JTAG External Modules for Cluster Test

    JEMIO - StarTest

    The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.

  • Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)

    PeakTech Prüf- und Messtechnik GmbH

    A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.

  • Memory Burn-In Test

    NEOSEM TECHNOLOGY INC

    The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies. Up to 64 Blades populated in one test head can test over 2000 DUTs in parallel. Neosem Technology’s high parallel DUT count architecture, combined with low capital cost, provides the absolute lowest HVM cost of test.

  • OBD ECU Simlator

    mOByDic1700 - Ozen Elektronik Inc.

    The J1939 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates a Truck ECU . Using 5 potensiometer , 5 live data can be changed and some fixed PNG values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. DM11 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 24 V power supply . More information you can get from the corresponding chipset datasheet.

  • Ohm-Stat Digital Display Megohmmeter

    Static Solutions Inc.

    Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester

  • Relay Buddy

    190 - Electronic Specialties Inc.

    Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.

  • Terminal Power Meter

    TPM-50A - ShinewayTech

    ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm;(3) Modulation bandwidth: 5MHz;(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.

  • Test Analysis for Land Seismic Systems

    Testif-i Land - Verif-i Ltd

    Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.

  • Turret Test Systems

    Moog Inc.

    The Moog Turret Test System is based on a high performance 6 Degrees of Freedom (DOF) electric motion system with powerful test software to simulate test tracks and test performance of the turret stabilizer. On the top platform of the Turret Tester, the user can install an actual turret or a remote weapon station. It can handle a wide range of payloads up to 24,000 kg (53,000 lb) and meet specific requirements related to particular excursions, velocities or accelerations. The Moog Replication software module has been developed to accurately simulate vehicle movements as recorded on the test track.

  • 200 Ampere Micro OHM Meters

    HL-200 - Neutronics Manufacturing Co.

    Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 200 is a direct reading tester, and uses a test current of 200A DC, resulting in true value and accurate measurements. Model HL- 200 adopts digital circuit technique and is used for measuring contact resistance of switch control equipment at test current of 200A DC. The measurements are accurate as the test is highly stable. HL- 200 is a new, fully automatic micro controlled tester that measures contact resistance at 200A DC with built in printer.

  • Traveling Wave Tube Test System

    Yelo Ltd.

    Yelo has a wealth of experience in developing and customizing test systems for the Travelling Wave Tube (TWT) market. TWT testers feature specialized power supplies, measurement equipment, and comprehensive control and safety systems.A rugged PLC is used to control all voltages and perform all monitoring functions. User interface and datalogging functions are provided by a supervisory PC that is electrically isolated from the PLC. Power Supplies are solid state with optical fibre barriers to ensure that all control/monitoring is carried out at safe voltages, and with maximum noise immunity. All safety interlocks are hardwired, and the testers are equipped with emergency shutdown features for added security.

  • LEON In-Circuit Test Systems

    Konrad Technologies GmbH

    The LEON Gen III Embedded PCB Tester combines classical analog in-circuit test (ICT) or manufacturing defect analysis (MDA) with additional functional test capabilities on a single PXI board. Multiple embedded testers can be configured in a single system for parallel test and high throughput.Highlights Combined test system ICT, FCT Digital test using JTAG In-system programming Open and flexible platform Small footprint Combines up to 6 instruments 2xPMU, 1xDVM, 1xHVCs 4xADC, 4x DAC High Speed Test Execution Parallel Test with max 16 modules Automated test sequencing Custom extension modules

  • Pressure Calibrators

    Fluke Calibration

    Wherever you need to work and whatever pressure range you need to work with, our broad selection of tools will meet your needs. From pneumatic or hydraulic deadweight testers and test pumps to electronic deadweight testers, bench controllers, and precise analog pressure gauges, we have you covered at the bench. Going into the field? Fluke’s portable pressure calibrators – with or without pumps and intrinsically safe or not – work with gases or liquids, source and measure, power transmitters, and cover a wide range. With individually available pressure modules, our portable and bench solutions cover pressures from vacuum to 10,000 psi.

  • Video Analyzer / Generator for HDMI 8K Testing

    M41h - Teledyne LeCroy quantumdata

    The Teledyne LeCroy quantumdata M41h 48G Video Analyzer/Generator for HDMI 8K Testing is a compact versatile test instrument offering entry level functional testing that can be extended through software licenses to a full compliance tester with sophisticated analysis and diagnostic capabilities. The M41h enables design and test engineers to validate their products for interoperability and reliability for the HDMI 2.1 video interface. The M41h is a flexible test instrument that can be upgraded from a functional tester for sources and sinks to a sophisticated analyzer and, if desired, can test full standards compliance, enabling developers to pre-test or self-test independently, reducing delays and costs during the product development cycle.

  • Home Inspector Kit

    MO280-KH - Extech Instruments Corporation

    Specifically designed for home inspection professionals—aids in identification of moisture, HVAC, electrical and hot water system issues. Kit includes a Pinless Moisture Meter for non-invasive measurement with a depth of 0.75" (22mm) below the surface, Mini InfraRed Thermometer that’s ideal for testing HVAC supply and return applications, an GFCI Receptacle Tester that detects 5 wiring faults in 3-wire receptacles and tests GFCI circuits, and a Waterproof Stem Thermometer with 2.75" (70mm) stainless steel stem that’s ideal for testing hot water heaters. Supplied in an attractive storage case that provides protection and organization for the testers whenever they are needed.

Get Help