Showing recent results 571 - 585 of 1616 products found.
-
Mensor Corp.
Hand-helds are portable calibration instruments for mobile use for the accurate measurement and recording of pressure profiles. There are interchangeable pressure sensors with measuring ranges of up to 8,000 bar available for the instruments. Through this, hand-helds are particularly suitable as test instruments for a large variety of applications in the widest range of industries. Data recorded in the hand-held can be evaluated via PC software. Some instruments document calibrations in the internal memory, which can later be read on a PC. Optionally, a calibration certificate can be generated with our calibration software WIKA-CAL.
-
N8330 Series - Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8330 is a programmable battery simulator with low-power, multi-channel and high-accuracy, supporting Max. 24 channels. Users can set the voltage and current for each channel by programming software, which is flexible, easy to operate and can meet the needs of multi-channel, multi-parameter and complex test environments. Each channel is isolated, which is convenient for series connection. N8330 software supports multi-channel batch operation. Data and curve for each channel can also be displayed. At the same time, data analysis and report functions are supported.
-
N8330D/E - Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8330D/E is a programmable battery simulator with low-power, multi-channel and high-accuracy, supporting Max. 4 channels. Users can set the voltage and current for each channel by programming software, which is flexible, easy to operate and can meet the needs of multi-channel, multi-parameter and complex test environments. Each channel is isolated, which is convenient for series connection. N8330D/E software supports multi-channel batch operation. Data and curve for each channel can also be displayed. At the same time, data analysis and report functions are supported.
-
OCD Commander - Macraigor Systems LLC
The OCD Commander is our free debugger software, which allows you to connect to your supported target type chip via the On-Chip Debug port (BDM or JTAG) using a Macraigor hardware device. You will be able to test the connection, memory access, modify memory and registers, run code and more using this product. This debugger is not designed to be used to program flash devices connected to your target. If you desire this functionality, please see our Flash Programmer software.
-
IOL INTACT® - UNH IOL
To meet the needs of its higher layer protocol based conformance testing, we have developed a custom software test tool and API, named IOL INTACT® (Improving Networks Through Automated Conformance Testing). A modular and cross-platform API with built in packet generating, scheduling, triggering, and filtering capabilities offering fully automated protocol analysis and testing, the IOL INTACT software is used in a number of our Testing Services including IPv6, Routing, and Home Networking.
-
Eastern-Optx
Eastern OptX now offers System Integration for all of our equipment along with other instruments including: RF, microwave, and Optical test equipment, power conditioning, distribution, and back-up, system controllers, and data recording devices. We also offer test solution development including mechanical design, rack layout, and custom control software. Eastern-OptX will help you to design and develop your test solution and deliver a completely assembled and tested system.
-
RT2 - ETAS GmbH
ETAS RT2 is a powerful test tool for testing of functional models (MiL) and software (SiL). It contains the following parts of the testing lifecycle: modeling, execution, assessment, and reporting. ETAS RT2 is specialized for testing of embedded systems with inputs and outputs of continuous or discrete signals. A model based test design approach enables intuitive realization of complex test strategies. Thanks to its capabilities ETAS RT2 enables comprehensive testing activities in the early phases of the development.
-
AWTS - Eclypse International
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
CommFront Communications
A data network does not consist only of hardware products; there are different types of software and protocols, and to make things even more complicated, many manufacturers have incorporated proprietary protocols for their devices. Integrating different devices and protocols within a data network is always the most challenging task for system integrators, firmware / software developers, and site engineers. With our powerful 232Anlayzer tools, controlling, monitoring, and debugging serial devices and high-level protocols have never been easier. The applications for our 232Analyzer tools range from the simplest loopback tests for both devices and serial data networks, to complicated protocol analysis and to sophisticated firmware and GUI software development. CommFront’s Serial-TCP software product (freeware) offers another ideal solution for merging serial communication protocols with modern TCP/IP communication, yielding benefits such as widely available infrastructures and greater distance, reliability, and speed.
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ Semi-automatic intelligent Digital Rockwell Hardness tester, you can automatically test the Rockwell hardness and surface Rockwell hardness measurement；◆ Automatic variable load, automatic loading, automatic unloading, automatic conversion, automatic measurement；◆ Friendly human-computer interaction，5.2“colorful LCD screen direct display test force,loading time,conversion value and indenter type etc； ◆ Automatically calculate and display the measured value, the maximum value, the minimum value, the average value and the hardness value deviation, the display shows the resolution 0.1HR；◆ There are functions such as hardness upper and lower limit settings, tolerance alarms, data graph analysis, average and (single point) batch measurement modes；◆ Software compensation function, the machine can be ± 3HR software compensation, no need to open the top cover for mechanical adjustment;◆ With automatic hardness conversion function, according to ASTM E140 conversion, no need to check the complex hardness of the table；◆ Multi-language features, can switch Chinese, English, German, Portuguese, Turkish, Czech, Korean and other languages；◆ Built-in 2000 single data storage function and 1000 group packet data storage function, can view a single data and data analysis；◆ Optional Bluetooth wireless printer to print the measurement data, no need to manually record and write test data；◆ Optional Softhard data analysis software and Bluetooth receiver on the test data for the computer into and analysis；◆ Support FexQMS measurement of large data analysis and control software to enhance the whole plant process control, reduce material loss.
-
IBEKO Power AB
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
Keysight Technologies
The wide range of available models and advanced measurement features provides a variety of price-performance points for parametric measurement and analysis. Modular product family members enable customization now and provide for future expansion as requirements change, while 2-channel units provide cost-effective solutions for simple test needs. The E5270B is targeted at precision semiconductor device characterization, and the E5260 Series (E5260A, E5262A, and E5263A) is targeted at high-speed production test. For all members of this product family, a number of innovative design elements -- such as expanded program memory -- help to improve the efficiency of complex testing. Cost-of-test is also lowered through superior measurement throughput, often several times faster than earlier instruments (such as the 4142B). The new 4.0 version of Keysight Desktop EasyEXPERT software can control the product family by using sample application tests on Desktop EasyEXPERT. The product family also gives you the option of using your own software.
-
MultiTest 0.5-i - Mecmesin Limited
he MultiTest 0.5-i provides a powerful and comprehensive tensile testing system for force measurements up to 0.5kN. With full programming capability and a large selection of analysis options, through the power of Emperor™ software, the MultiTest 1-i offers unparalleled tensile test versatility.
-
VIS 400 - Optical Design Manufacturing, Inc.
The VIS 400-HDP inspection scope allows test technicians to inspect and grade fiber endfaces by offering the most detailed image possible. When used in conjunction with ODM’s proprietary InSpec™ software the VIS 400 ensures compliance with the IEC 61300-3-35 standard.
-
Plottergeist - Aphena Ltd
Plottergeist "the phantom plotter" emulates all the common HPGL plotters. It runs on a standard PC equipped with a GPIB card or using RS-232, and connects to test equipment or another computer. The software behaves like a real plotter, with the exception that the PC screen is the paper.
