-
product
Keysight Triple 1x2 SPDT Unterminated Microwave Switch Module for 34980A
34947A
The Keysight 34947A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as three independent 1x2 (SPDT) unterminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 510 Ohm - SPST
40-294-114
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-02
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
19" Enclosures for 6U VME VPX Boards
R4U8S
The R4U8S is a 4U height 19'' Rack Mount Industrial Chassis featuring 8 slots of either VME or cPCI 6U size boards. The R4U8S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications.
-
product
PXI Analog Output
Our range of flexible PXI Analog Output modules features high accuracy & high resolution voltage and current sources that satisfy a wide variety of applications in Automated Test, including sensor and transducer simulation. Each product has a number of variants with differing channel counts to closely match a user’s specific requirements.
-
product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
product
Plus Super Phosphor Oscilloscopes
SDS2000X
The SDS2000X Plus series employs SIGLENT’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search a...show more -
product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 472Ω
40-253-020
The 40-253-020 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
FPGA PXI High-Performance Digital I/O Card
GX3702
The GX3702 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3702 is supplied with an integral expansion board providing access to the FPGA's 160 I/Os and is pin for pin compatible with the N...show more -
product
New Battery Conductance Tester
Hangzhou Xun Anda Electrical Co., Ltd.
1. Test application: 12V/6V batteries test and 12V Starting /Charging system test.2. Test battery type: regular liquid, AGM battery, GEL battery,VRLA battery3. CCA test range: 40~2000CCA (SAE).4. Voltage test range: 1.5-15V.5. Display SOH (state of health), SOC(state of charge).6. Test for multiple battery standards: SAE, DIN, EN, IEC, CA.7. Graphic LCD display with back light, LCD brightness adjustable.8. Multigle language operation: English, Chinese, Germany, French, Spanish. 9.internal resistance
-
product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x
MIL-STD-1553 Test and Simulation Module for PCI Express with 1, 2 or 4 Dual Redundant channels (APE1553-1, APE1553-2, APE1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APE1553-x module is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
product
PXI 3A Power MUX BRIC, 32-Channel, 6-Pole
40-571-404
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Decade Box, Calibrated W/Data, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL D
The 72-7265 CAL D from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 11.4MΩ
50-297-153
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 3A Power MUX BRIC, 3-Channel, 48-Pole
40-571-003
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXIe-2575, 196‐Channel, 1-Wire PXI Multiplexer Switch Module
780587-75
196‐Channel, 1-Wire PXI Multiplexer Switch Module —The PXIe‑2575 is a high‐density PXI multiplexer switch module that is ideal for high‑channel‑count automated test applications. It uses electromechanical relays and can route hundreds of signals to measurement devices or from source units. The PXIe‑2575 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Anite Development Toolset
Benefit from a comprehensive suite of tools that support all phases of wireless terminal development, from pre-silicon protocol module development through to systems integration and verificationGain easy access to parameters at lower layers to re-create tests in the very early stages of chipset and device developmentAccess an extensive LTE/LTE-Advanced technology roadmap including early 5G specificationsRemain in control of test designs through accessing Layer 1 and Layer 2 using Application Programming Interfaces (APIs)Benefit from a high level of flexibility and control in terms of test creation
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 5.82MΩ
50-297-152
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Downconverters
This high performance down converter is intended for use in professional applications in C band such as satellite earth stations. BMCD100 unit is suitable for outdoor C band transmission tests.
-
product
PXI-6281, 16 AI (18-Bit, 625 kS/s), 2 AO, 24 DIO, PXI Hybrid, Multifunction I/O Module
779121-01
16 AI (18-Bit, 625 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXI‑6281 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
Aerospace
AcQ can perform custom developments compliant with ED12/DO-178B and ED80/DO-254 in various design assurance levels (DALs) for safety critical applications, using the ED14/DO160 for the environmental requirements. AcQ also offers standard products for various open standards like VMEbus, CPCI, PCI and other bus standards for test applications and other applications like GPS, display, actuators, data logging and -storage.
-
product
Test Executive for Visual Development, Database Storage, and Run-Time Execution of Test Strategies
TestBase
TYX TestBase is a test executive that supports the visual development, database storage and run-time execution of test strategies (also known as test plans or test sequences).TestBase integrates third-party applications such as: test programming languages, document viewers, report generators, database engines, Configuration Management systems and diagnostic tools.Its modular and open architecture enables system integrators and end-users to customize and extend the product and to integrate additional third-party applications.
-
product
150 Amps, 10 MHz BW Current Probe - AC/DC , 500 Amp Peak Pulse
CP150
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Electromechanical Transfer Switches up to 40 GHz
Fairview Microwave’s line of electromechanical relay transfer switches can be utilized for numerous applications to increase system level capabilities and can help simplify the overall design approach. With two input and two output ports, transfer switches can connect two different instruments with two devices under test. Additionally, they can be used as drop-out switches, for signal reversal or to bypass a component under test. These products are typically used in military communications and broadcast systems, SATCOM, test & measurement, instrumentation applications and are suitable for aircraft use.
-
product
PXI-6233, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779620-01
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6233 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements...show more -
product
Mobility Assurance Service
Mobile testing ensures the quality of applications and other digital properties running on mobile devices. The dynamism, complexity and competitive nature of the mobile application space makes it imperative that publishers choose a highly responsive and well-equipped test partner to ensure the greatest user experience of their digital properties across all types of mobile devices.- Mobile testing involves all testing types (functional, performance, etc).- Mobile application testing involves thou...show more -
product
PXI Precision Resistor Module 6-Channel, 2.5 to 773k
40-297-043
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
In-Circuit Fixtures
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
product
Ultrasonic Leak Detector
7635
Peaceful Thriving Enterprise Co Ltd
Ultrasonic leak detector utilizes ultrasonic sensor to check the air-tightness of pipeline. The operation is easy and accurate. The instrument can identify the gas leakage of various pressure or vacuum system. The transmitter will generate 40kHz ultrasonic signal, and it is used in conjunction with the detector to detect the leaking location of the object. For example, the detector will detect signal leaking from the hole of the pipeline and as user moves the detector, the hole can be located correctly. The main application is the tightness test of any kinds, for example, doors, windows, plumbing, container, car windows, refrigerators … etc.
